CCNA2 Final Exam 2013 - reeks 1

Bitte warte - es wird geladen…

Frage 1 von 50

Which of the following are required when adding a network to the OSPF routing process configuration?

Wähle eine oder mehr der folgenden:

network address
loopback address
autonomous system number
subnet mask
wildcard mask
area ID

Erklärung

Frage 2 von 50

Which of the following are primary functions of a router? (Choose two.)

Wähle eine oder mehr der folgenden:

packet switching
microsegmentation
domain name resolution
path selection
flow control

Erklärung

Frage 3 von 50

Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)

Wähle eine oder mehr der folgenden:

The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.

Erklärung

Frage 4 von 50

Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)

Wähle eine oder mehr der folgenden:

10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
192.168.2.0/24

Erklärung

Frage 5 von 50

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?
when there is a low bandwidth connection

Wähle eine oder mehr der folgenden:

when there is a low bandwidth connection
when the connection is on a shared medium
when the connection is serial instead of Ethernet
when the link is always busy

Erklärung

Frage 6 von 50

Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?

Wähle eine oder mehr der folgenden:

C-B-E-D
C-B-A-D
C-F-E-D
C-F-B-A-D
C-F-E-A-D

Erklärung

Frage 7 von 50

What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks?

Wähle eine oder mehr der folgenden:

hello
LSU
LSR
DBD
LSAck

Erklärung

Frage 8 von 50

Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?

Wähle eine oder mehr der folgenden:

the IP address of the Fa0/0 interface at R1
the IP address of the S0/0/1 interface at R2
the IP address of the S0/0/0 interface at R1
the subnet mask of the S0/0/1 interface at R2

Erklärung

Frage 9 von 50

Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?

Wähle eine oder mehr der folgenden:

192.168.1.0/24
192.168.0.0/24
192.168.0.0/22
192.168.1.0/22

Erklärung

Frage 10 von 50

Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)

Wähle eine oder mehr der folgenden:

R 172.16.1.0/24 [120/1] via 192.168.3.0, 00:00:24, Serial0/0/0
R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1
R 192.168.9.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0
R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0
R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0

Erklärung

Frage 11 von 50

A router boots and enters setup mode. What is the reason for this?

Wähle eine oder mehr der folgenden:

The IOS image is corrupt.
Cisco IOS is missing from flash memory.
The configuration file is missing from NVRAM.
The POST process has detected hardware failure.

Erklärung

Frage 12 von 50

Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?

Wähle eine oder mehr der folgenden:

Compared to RIP, EIGRP has a lower administrative distance.
Compared to EIGRP, RIP has a higher metric value for the route.
Compared to RIP, the EIGRP route has fewer hops.
Compared to RIP, EIGRP has a faster update timer.

Erklärung

Frage 13 von 50

All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID?

Wähle eine oder mehr der folgenden:

The highest MAC address among the active interfaces of the network will be used.
There will be no router ID until a loopback interface is configured.
The highest IP address among the active FastEthernet interfaces that are running OSPF will be used.
The highest IP address among the active interfaces will be used.

Erklärung

Frage 14 von 50

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. What action should be taken to solve this problem?

Wähle eine oder mehr der folgenden:

Enable the serial interfaces of both routers.
Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
Configure both routers with the same EIGRP process ID.

Erklärung

Frage 15 von 50

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Wähle eine oder mehr der folgenden:

Check if the interfaces of the routers are enabled.
Check the hello and dead intervals between the routers.
Check the process ID of both routers.
Check if CDP is enabled on all the routers.

Erklärung

Frage 16 von 50

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Wähle eine oder mehr der folgenden:

Configure the router ID on both routers.
Configure the R2 router interfaces for area 0.
Configure a loopback interface on both routers.
Configure the proper subnet masks on the router interfaces.

Erklärung

Frage 17 von 50

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Wähle eine oder mehr der folgenden:

A static route will be updated in the routing table.
The traffic from the Internet will be directed to R2.
The traffic from the source network 172.16.0.0/22 will be blocked.
The route will be specified as the default route for all networks not defined in the routing table.
All the broadcasts will be forwarded via the S0/0/0 interface of R2.

Erklärung

Frage 18 von 50

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.Which path will be used to transmit the data?

Wähle eine oder mehr der folgenden:

The data will be transmitted via R3-R2.
The data will be transmitted via R3-R1-R2.
The traffic will be load-balanced between two paths — one via R3-R2, and the other via R3-R1-R2.
The data will be transmitted via R3-R2, and the other path via R3-R1-R2 will be retained as the backup path.

Erklärung

Frage 19 von 50

Refer to the exhibit. What is the meaning of the highlighted value 120?

Wähle eine oder mehr der folgenden:

It is the metric that is calculated by the routing protocol.
It is the value that is used by the DUAL algorithm to determine the bandwidth for the link.
It is the administrative distance of the routing protocol.
It is the hold-down time, measured in seconds, before the next update.

Erklärung

Frage 20 von 50

In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?

Wähle eine oder mehr der folgenden:

R 192.168.1.0/24 [120/3] via 192.168.110.1, 00:00:17, Serial0/1/0
R 192.168.1.0/24 [120/2] via 192.168.200.1, 00:00:17, Serial0/0/0
R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial0/0/1
R 192.168.1.0/24 [120/4] via 192.168.101.1, 00:00:17, Serial0/1/1

Erklärung

Frage 21 von 50

Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?

Wähle eine oder mehr der folgenden:

An incorrect IP address is configured between the two routers.
No static route is configured on Router2.
A routing loop has occurred.
No routing protocol is configured on either of the two routers.

Erklärung

Frage 22 von 50

How does route poisoning prevent routing loops?

Wähle eine oder mehr der folgenden:

New routing updates are ignored until the network has converged.
Failed routes are advertised with a metric of infinity.
A route is marked as unavailable when its Time to Live is exceeded.
The unreachable route is cleared from the routing table after the invalid timer expires.

Erklärung

Frage 23 von 50

Which statement is true about the metrics used by routing protocols?

Wähle eine oder mehr der folgenden:

A metric is a value used by a particular routing protocol to compare paths to remote networks.
A common metric is used by all routing protocols.
The metric with the highest value is installed in the routing table.
The router may use only one parameter at a time to calculate the metric.

Erklärung

Frage 24 von 50

Which statement correctly describes a feature of RIP?

Wähle eine oder mehr der folgenden:

RIP is a link-state routing protocol.
RIP uses only one metric—hop count— for path selection.
Advertised routes with hop counts greater than 10 are unreachable.
Messages are broadcast every 10 seconds.

Erklärung

Frage 25 von 50

Refer to the exhibit. OSPF is used for the routing protocol and all interfaces are configured with the correct IP addresses and subnet masks. During testing, it is found that router R1 is unable to form an adjacency with R2. What is the cause of this problem?

Wähle eine oder mehr der folgenden:

Both routers have been configured with incorrect router IDs.
Both routers have been configured in different OSPF areas.
Both routers have been configured with an incorrect network type.
Both routers have been configured with different hello and dead intervals.

Erklärung

Frage 26 von 50

A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?

Wähle eine oder mehr der folgenden:

hub
router
access point
Ethernet switch

Erklärung

Frage 27 von 50

Which network and mask combination requires the use of a classless addressing solution?

Wähle eine oder mehr der folgenden:

10.32.0.0/11
172.16.0.0/12
192.168.0.0/24
192.168.128.32/27

Erklärung

Frage 28 von 50

A company is using static routes that are configured with an administrative distance of “1” on all routers in the network. The network administrator decides to introduce a dynamic routing protocol to reduce the manual configurations for the static routes. Which option identifies the correct procedure for the dynamic routing to take place in the network?

Wähle eine oder mehr der folgenden:

The static routes and the dynamic routes will have the traffic alternate between them.
The static routes will be automatically removed once the dynamic routing is configured.
The static routes will be automatically updated with the next hop IP address once the dynamic routing is configured.
The static routes must be manually removed from all routers in order for the dynamic routes to be installed in the routing table.

Erklärung

Frage 29 von 50

Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?
The login command was not entered on the console line.

Wähle eine oder mehr der folgenden:

The login command was not entered on the console line.
The enable password should be an enable secret password.
No username and password combination has been configured.
Console connections cannot be configured to require users to provide passwords.

Erklärung

Frage 30 von 50

Refer to the exhibit. When a static IP address is being configured on the host, what address should be used for the default gateway?

Wähle eine oder mehr der folgenden:

10.1.1.1
10.1.1.2
172.16.1.1
192.168.1.1

Erklärung

Frage 31 von 50

Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of addresses and prefixes could be used to create an addressing solution with a minimum waste of IP addresses?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 32 von 50

Refer to the exhibit. The network is configured for OSPF routing with default settings. The bandwidths have been configured correctly for each link. If the T1 link between router A and router E fails, what path will a packet from router A take to reach the LAN attached to router F when the network has converged?

Wähle eine oder mehr der folgenden:

A, B, C, F
A, B, C, E, F
A, D, G, E, F
A, D, G, H, F

Erklärung

Frage 33 von 50

Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?

Wähle eine oder mehr der folgenden:

10.30.0.0/16
10.30.15.0/23
10.30.16.0/24
10.30.16.32/27
10.30.16.32/30

Erklärung

Frage 34 von 50

Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?

Wähle eine oder mehr der folgenden:

Disable the load balancing feature of RIPv2.
Issue the no auto-summary command for RIPv2.
Replace RIPv2 with EIGRP which supports VLSM.
Make sure that the network statements include the correct subnet mask.

Erklärung

Frage 35 von 50

Which multicast address does EIGRP use to send hello and updates packets?

Wähle eine oder mehr der folgenden:

224.0.0.5
224.0.0.6
224.0.0.9
224.0.0.10

Erklärung

Frage 36 von 50

Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down?

Wähle eine oder mehr der folgenden:

An IP address has not been configured on the interface.
The WIC was installed into the incorrect slot on the router.
The default encapsulation on the interface has been modified.
The no shutdown command has not been executed on the interface.

Erklärung

Frage 37 von 50

Refer to the exhibit. How was the OSPF default gateway entry for R2 determined?

Wähle eine oder mehr der folgenden:

Default routes are automatically injected by OSPF into all advertisements.
A static default gateway route is defined in the configuration of R2.
The default-information originate command is applied on R1.
The ISP defines the gateway of last resort and automatically passes it to R1 and R2.
The ip default-gateway command is applied on R2.

Erklärung

Frage 38 von 50

Refer to the exhibit. RIPv1 has been properly configured on all routers in the network. However, users on LAN2 have intermittent connectivity with the users on LAN1 and LAN3. What is the cause of the problem?

Wähle eine oder mehr der folgenden:

Both LAN networks are separated from router R2 with a variably subnetted Class C network 209.165.200.0/30.
Neither router R1 nor router R3 has a static route configured that points to the variably subnetted 172.16.0.0/24 networks.
Both routers R1 and R3 are sending the summarized 172.16.0.0/16 network to R2 in their RIPv1 routing updates.
Both networks 172.16.1.0/24 and 172.16.100.0/24 are configured with a subnet mask different from the default classful mask

Erklärung

Frage 39 von 50

Which default EIGRP configuration must be modified to allow an EIGRP router to advertise subnets that are configured with VLSM?

Wähle eine oder mehr der folgenden:

split horizon
metric K values
autosummarization
hello and dead intervals

Erklärung

Frage 40 von 50

What is a successor for a destination network in an EIGRP network?

Wähle eine oder mehr der folgenden:

the next hop on a backup route with the largest feasible distance to the destination
the next hop on a backup route with the smallest feasible distance to the destination
the next hop on the primary route with the largest feasible distance to the destination
the next hop on the primary route with the smallest feasible distance to the destination

Erklärung

Frage 41 von 50

Refer to the exhibit. Which route will be removed from the routing table if manual EIGRP summarization is disabled on the Serial0/0/0 interface of Router3?

Wähle eine oder mehr der folgenden:

0.0.0.0/0
172.16.0.0/16
172.16.1.0/24
172.16.3.0/30

Erklärung

Frage 42 von 50

Which port can be used for initial router configuration?

Wähle eine oder mehr der folgenden:

AUX
vty 0
s0/0/0
console

Erklärung

Frage 43 von 50

Which two link-state routing protocol challenges does OSPF resolve through the election of a DR? (Choose two.)

Wähle eine oder mehr der folgenden:

the extensive flooding of LSAs throughout the OSPF area
the excessive adjacencies when the number of routers increases
the requirement for link-state database updates to be propagated between OSPF areas
the heavy CPU load that is imposed because each router must compute shortest paths by using the SPF algorithm
the requirement for each router to build a topological database of the internetwork to determine the shortest paths between networks

Erklärung

Frage 44 von 50

A routing table shows an EIGRP route to 192.168.1.0/24 with a metric of 301440. What other term also describes this EIGRP metric value?

Wähle eine oder mehr der folgenden:

feasible distance
reported distance
feasible successor
feasibility condition

Erklärung

Frage 45 von 50

Refer to the exhibit. The network administrator has run the following command on R1.
R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2
What is the result of running this command?

Wähle eine oder mehr der folgenden:

Traffic for network 192.168.2.0 is forwarded to 172.16.1.2.
This route is automatically propagated throughout the entire network.
Traffic for all networks is forwarded to 172.16.1.2.
The command invokes a dynamic routing protocol for 192.168.2.0.

Erklärung

Frage 46 von 50

Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?

Wähle eine oder mehr der folgenden:

The Dijkstra algorithm will calculate the feasible successor.
DUAL will query neighbors for a route to network 192.168.1.0.
Neighbor 172.16.3.2 will be promoted to the feasible successor.
Traffic destined to the 192.168.1.0 network will be dropped immediately due to lack of a feasible successor.

Erklärung

Frage 47 von 50

Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once the administrator is connected to the router, which password should the administrator enter at the R1> prompt to access the privileged EXEC mode?

Wähle eine oder mehr der folgenden:

Cisco001
Cisco123
Cisco789
Cisco901

Erklärung

Frage 48 von 50

Refer to the exhibit. Which option will provide the configuration that is needed for router R1 to dynamically learn routes to the 192.168.100.16/28, 192.168.100.32/28, and 192.168.100.48/28 subnetworks?

Wähle eine oder mehr der folgenden:

with static routes
with a routed protocol
with a routing protocol
with directly connected routes

Erklärung

Frage 49 von 50

Refer to the exhibit. What will happen when the router reloads?

Wähle eine oder mehr der folgenden:

It will boot into ROMMON mode.
It will ignore the start-up configuration file.
It will look for the start-up configuration file on the TFTP server.
It will attempt to load the start-up configuration file that is stored in NVRAM.

Erklärung

Frage 50 von 50

On a router, which actions can be performed in user mode?

Wähle eine oder mehr der folgenden:

perform password recovery
make global configuration changes
view status of various router functions
make changes to a specified interface

Erklärung

["https://cdn.goconqr.com/uploads/checkbox_question/image/890984/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/890987/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/890990/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/890998/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891000/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891003/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891005/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891007/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891009/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891011/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891012/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891014/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891015/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891019/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891025/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891060/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891062/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891073/desktop_3.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891075/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891079/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891081/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891084/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891086/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891092/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891101/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891102/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891105/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891106/desktop_5.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/891109/desktop_5.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/1314946/desktop_1.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/1314947/desktop_2.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/1314948/desktop_3.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/1314949/desktop_4.jpg"]

	Erstellt von oliver_va vor mehr als 9 Jahre

Quiz am CCNA2 Final Exam 2013 - reeks 1, erstellt von oliver_va am 01/11/2014.

CCNA2 Final Exam 2013 - reeks 1

Frage 1 von 50

Which of the following are required when adding a network to the OSPF routing process configuration?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 2 von 50

Which of the following are primary functions of a router? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 3 von 50

Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 4 von 50

Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 5 von 50

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command? when there is a low bandwidth connection

Wähle eine oder mehr der folgenden:

Erklärung

Frage 6 von 50

Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 7 von 50

What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 8 von 50

Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 9 von 50

Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 10 von 50

Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 11 von 50

A router boots and enters setup mode. What is the reason for this?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 12 von 50

Wähle eine oder mehr der folgenden:

Erklärung

Frage 13 von 50

All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 14 von 50

Wähle eine oder mehr der folgenden:

Erklärung

Frage 15 von 50

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 16 von 50

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 17 von 50

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 18 von 50

Wähle eine oder mehr der folgenden:

Erklärung

Frage 19 von 50

Refer to the exhibit. What is the meaning of the highlighted value 120?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 20 von 50

In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?

Wähle eine oder mehr der folgenden:

Erklärung

Frage 21 von 50

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?
when there is a low bandwidth connection

Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?
The login command was not entered on the console line.