kc1352A851N Edit 1

1

What structural areas allow maintenance to inspect or service aircraft components?

1

Which major structural area provides support for the engines?

1

Which is not a major aircraft structural area?

1

Which component guards against accidental firing of ejection seats?

1

How do independent positioning determine subsystem function?

1

which is not an avionics system?

1

which is not part of an engine indicating system

1

what is normally considered a minimum safe distance from the intake of an operating jet engine?

1

When approaching overheated aircraft wheels, always approach the wheel

1

initially what happens when RF energy is absorbed in the tissue of your body

1

what is the minimum safe distance from an UHF antenna when the associated transmitter is radiating power?

1

the minimum safe distance from an HF antenna when the associated transmitter is radiating power is

1

which condition is usually not caused by an over exposure to noise?

1

the greatest noise levels around an operating jet aircraft engine is to rear of the engine through an angle of

1

which physical symptom is least likely to indicate a person is suffering from over exposure to noise?

1

which is a condition that results from frequent exposure to small overdoses of noise

1

which is not an Air Force inspection concept

1

which units fall under the programmed depot maintenance inspection concept

1

which inspection is designed to detect defects that might have developed during ground operations of the aircraft

1

when is the thruflight inspection perfromed

1

which inspection is more extensive than the hourly postflight or basic postflight inspections and covers certain parts, areas, and systems of the aircraft that require less frequent inspections

1

when the HSC inspection becomes due during a long-range mission, it is completed at the base

1

which inspection includes a review of the forms for current status, a visual inspection of equipment for defects, and adequate servicing

1

malfunctions documented on an AFTO form 244 are the responsibility of

1

Part V of the AFTO form 244 is used to document

1

the AFTO form 781 series would not be used to document aircraft

1

except for battle damage, each discrepancy discovered is documented on AFTO form 781

1

at what point do you erase symbols you entered on the AFTO form 781A

1

who ensures the job control number (when assigned) is entered on the AFTO form 781 A

1

which information is required in the corrective action block of the AFTO form 781 A

1

who is responsible for the validity and legibility of all comsec required entries

1

which AFTO form is used to document maintenance status and servicing information

1

which AFTO form is used to document aerospace vehicle time and engine data including operating time

1

Which AFTO form allows you to record essential inspection and delayed maintenance data

1

Block C of the AFTO form 781K is used to document

1

to "flag" a condition on an aircraft that could cause damage or injury of ignored, use

1

What portion of the tag is used to provide a "cross-check" with the aircraft forms and is inserted through the aircraft forms binder

1

what helps to dissipate and lessen the effects of electronic discharge

1

an example of an ESDS devise is a

1

what type of failure associated with ESD is the most difficult to detect

1

which is not a flight line precaution used to protect ESDS components?

1

when working on ESDS devices in the shop area, you must use

1

what type of ground do you need to provide for soldering irons in an ESD protected area

1

which action could pose a safety hazard to personnel in an ESD protected area

1

which type of cable carries RF power from one point to another with a known rate of loss

1

which is not a type of connector coupling

1

all of the following are rf connectors precautions except

1

twisting of the fiber optic cable during installation or maintenance results in

1

what is not an advantage of fiber optic cables over wire cables?

1

optoelectric transducer detectors perform what functions in a fiber optic transmission

1

utilizing exact dimensions for stripping wire ensures

1

flux is designed to

1

proper care of an electric soldiering iron involves

1

which is not a type of solderless connector

1

what type of solderless connector permits easy and efficient connections to electrical equipment

1

one purpose of crimper positioner is to

1

the colored end of an insertion and extraction is used for contact

1

one way of pressure and moisture sealing the back of a connector is to use

1

the MIL-STD that governs heat tool operation in a potentially explosive environment is

1

the heat and air pressure required for proper installation of heat shrink products is controlled by the

1

as a flight line technician, you can repair up to

1

Before performing any type of wire repair, you must consult the procedures in TO

1

what precaution must you adhere to prior to heat shrink to a wire repair job

1

what is the purpose of prewaxing cotton or linen tape when used for wire bundling

1

which of the following is not considered a general precaution when lacing or tying wire groups or bundles

1

the circuit used in an AM trasmitter to bring the oscillator frequency up to the designated frequency required for carrier wave operation is

1

to achieve AM, what device is used to ensure the output signal contains frequencies not present in the input signals

1

the frequencies created by the heterodyning process in an AM transmitter modulator are the

1

which is not a basic characteristic that can vary in a modulating wave or signal?

1

in an FM signal, the amount of frequency modulation is controlled by the modulating signal's

1

in an FM transmitter, the frequency of the oscillator is controlled by the

1

in an FM transmitter, which circuit detects the output frequency changes and produce an automatic frequency control correction voltage?

1

the low pass filter in the automatic frequency control circuitry of a FM transmitter prevents

1

which is not an advantage of single sideband over double sideband

1

in a single sideband transmitter, frequency stability is controlled by

1

in a single sideband transmitter, the balanced modulator's output consists of

1

the single sideband transmitter circuit that increases the power output without introducing distortion is the

1

the ability of a radio receiver to select a particular station frequency from all other station frequencies that appear at the receiver antenna is called

1

In a typical AM superheterodyne receiver, the process used to tune two or more circuits with a single control is called

1

in a typical AM superheterodyne receiver, the heterodyning process produces four frequencies; they are the two basic input frequencies, there sum, and their difference frequency is known as the

1

the purpose of the limiter circuit in an FM receiver is to

1

FM modulation signals provide much more realistic sound reproduction than AM signals because

1

the two advantages of using a single-sideband receiver over an AM receiver are the ability to place

1

the basic difference between the single sideband receiver and a conventional superheterodyne receiver is that the single-sideband receiver uses a

1

a major drawback in using a single sideband recierver over an amplitude modulated receiver is the

1

a receiver radio antenna receives radio frequency signals by

1

the ratio of the maximum radiation intensity of a given directional radio antenna to the radiation intensity of a non directional radio antenna using the same power input is known as antenna

1

the radio frequency line that has uniform capacitance between the conductors throughout the length of the line is the

1

when the impedance of a radio frequency transmission line and load do not match, the reflected wave and the applied wave are on the line at the same time are creating a

1

what type of radio frequency transmission line losses result from the skin effect?

Volume 2 URE

kc1352A851N Edit 1

kc1352A851N Edit 1

What structural areas allow maintenance to inspect or service aircraft components?

Which major structural area provides support for the engines?

Which is not a major aircraft structural area?

Which component guards against accidental firing of ejection seats?

How do independent positioning determine subsystem function?

which is not an avionics system?

which is not part of an engine indicating system

what is normally considered a minimum safe distance from the intake of an operating jet engine?

When approaching overheated aircraft wheels, always approach the wheel

initially what happens when RF energy is absorbed in the tissue of your body

what is the minimum safe distance from an UHF antenna when the associated transmitter is radiating power?

the minimum safe distance from an HF antenna when the associated transmitter is radiating power is

which condition is usually not caused by an over exposure to noise?

the greatest noise levels around an operating jet aircraft engine is to rear of the engine through an angle of

which physical symptom is least likely to indicate a person is suffering from over exposure to noise?

which is a condition that results from frequent exposure to small overdoses of noise

which is not an Air Force inspection concept

which units fall under the programmed depot maintenance inspection concept

which inspection is designed to detect defects that might have developed during ground operations of the aircraft