CCNA 3 Practice Quiz

Frage 1 von 63

1

Which technology is required when switched networks are designed to include redundant links?

Wähle eine der folgenden:

Spanning Tree Protocol
virtual LANs
link aggregation
virtual private networks

Erklärung

Frage 2 von 63

1

Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?

Wähle eine der folgenden:

STP
Rapid PVST+
PVST+
MST

Erklärung

Frage 3 von 63

1

Which statement describes a characteristic of Cisco Meraki switches?

Wähle eine der folgenden:

They are service provider switches that aggregate traffic at the edge of the network.
They are cloud-managed access switches that enable virtual stacking of switches.
They are campus LAN switches that perform the same functions as Cisco 2960 switches.
They promote infrastructure scalability, operational continuity, and transport flexibility.

Erklärung

Frage 4 von 63

1

If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?

Wähle eine der folgenden:

highest IP address
lowest MAC address
lowest IP address
highest MAC address

Erklärung

Frage 5 von 63

1

What is a characteristic of a Layer 2 loop?

Wähle eine der folgenden:

A switch is continually forwarding the same unicast frame.
Broadcast frames are forwarded back to the sending switch.
Routers continually forward packets to other routers.
The Time-to-Live attribute of a frame is set to infinity.

Erklärung

Frage 6 von 63

1

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Wähle eine oder mehr der folgenden:

redundant links between Layer 2 switches
removing single points of failure with multiple Layer 2 switches
link-state dynamic routing that provides redundant routes
static default routes
implementing VLANs to contain broadcasts

Erklärung

Frage 7 von 63

1

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Wähle eine oder mehr der folgenden:

listening
learning
forwarding
disabled
blocking

Erklärung

Frage 8 von 63

1

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Wähle eine der folgenden:

root port
disabled port
alternate
designated port

Erklärung

Frage 9 von 63

1

What is an advantage of using LACP?

Wähle eine der folgenden:

decreases the chance of a spanning-tree loop
provides a simulated environment for testing link aggregation
allows automatic formation of EtherChannel links
decreases the amount of configuration that is needed on a switch for EtherChannel
increases redundancy to Layer 3 devices

Erklärung

Frage 10 von 63

1

Which command will initiate EtherChannel interface configuration mode?

Wähle eine der folgenden:

interface port-channel interface-identifier
interface interface-identifier
interface range interface-identifier
channel-group group-identifier

Erklärung

Frage 11 von 63

1

Which PAgP mode combination will establish an EtherChannel?

Wähle eine der folgenden:

switch 1 set to desirable; switch 2 set to desirable.
switch 1 set to on; switch 2 set to desirable.
switch 1 set to auto; switch 2 set to auto.
switch 1 set to auto; switch 2 set to on.

Erklärung

Frage 12 von 63

1

When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?

Wähle eine der folgenden:

active
desirable
auto
passive

Erklärung

Frage 13 von 63

1

When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?

Wähle eine der folgenden:

desirable
auto
active
passive

Erklärung

Frage 14 von 63

1

What type of wireless antenna is best suited for providing coverage in large open spaces, such as hallways or large conference rooms?

Wähle eine der folgenden:

Yagi
omnidirectional
directional
dish

Erklärung

Frage 15 von 63

1

During which stage of establishing connectivity between a WLAN client and an AP does the client learn the MAC address of the AP?

Wähle eine der folgenden:

encryption
authentication
discovery
association
probing

Erklärung

Frage 16 von 63

1

A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?

Wähle eine der folgenden:

Issue the clear ip ospf process privileged mode command.
Configure the network statements.
Change the OSPFv2 process ID.
Change the interface priority.

Erklärung

Frage 17 von 63

1

Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

Wähle eine oder mehr der folgenden:

The DR can be reached through the GigabitEthernet 0/0 interface.
There have been 9 seconds since the last hello packet sent.
The router ID on the DR router is 3.3.3.3
The BDR has three neighbors.
The router ID values were not the criteria used to select the DR and the BDR.
This interface is using the default priority.

Erklärung

Frage 18 von 63

1

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

Wähle eine der folgenden:

show ipv6 ospf interface serial 0/0/0
show ip ospf neighbor
show ip ospf interface serial 0/0/0
show ip ospf interface fastethernet 0/1

Erklärung

Frage 19 von 63

1

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

Wähle eine der folgenden:

The R1 dead timer expires between hello packets from R2.
The neighbor adjacency has formed.
R1 automatically adjusts its own timers to match the R2 timers.
The hello timer on R2 expires every ten seconds.

Erklärung

Frage 20 von 63

1

A network engineer is troubleshooting convergence and adjacency issues in an OSPFv2 network and has noted that some expected network route entries are not displayed in the routing table. Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)

Wähle eine oder mehr der folgenden:

show running-configuration
show ip ospf neighbor
show ip ospf interface
show ip route ospf
show ip protocols

Erklärung

Frage 21 von 63

1

A network engineer is troubleshooting an OSPFv2 network and discovers that two routers connected by a point-to-point WAN serial link are not establishing an adjacency. The OSPF routing process, network commands and area ID are all confirmed as correct, and the interfaces are not passive. Testing shows that the cabling is correct, that the link is up, and pings between the interfaces are successful. What is most likely the problem?

Wähle eine der folgenden:

A clock rate has not been set on the DCE interface of the serial link.
The OSPFv2 process IDs on each router do not match.
A DR election has not taken place.
The subnet masks on the two connected serial interfaces do not match.

Erklärung

Frage 22 von 63

1

A network engineer is troubleshooting OSPFv2 routing issues on two connected routers. Which two requirements to form an adjacency need to be verified? (Choose two.)

Wähle eine oder mehr der folgenden:

Verify that the interfaces that connect the two routers are in the same area.
Verify that one of the routers is the DR or BDR and the other router a DRother.
Verify that one of the interfaces that connects the two routers is active and the other passive.
Verify that the interfaces that connect the two routers are in the same subnet.
Verify that both routers are using the same OSPFv2 process ID.

Erklärung

Frage 23 von 63

1

Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?

Wähle eine der folgenden:

show ip protocols
show ip ospf interface
show ip interface brief
show ip route ospf

Erklärung

Frage 24 von 63

1

Refer to the exhibit. Four routers are connected to an Ethernet LAN segment and are configured to run OSPFv3. However, none of the routers are receiving routing updates. What is the cause of the problem?

Wähle eine der folgenden:

The routers are using IPv6 link local addresses to communicate.
The network type has been set to BROADCAST instead of NBMA.
The routers are using IPv4 addresses for router IDs.
All of the routers have an OSPFv3 interface priority of 0.

Erklärung

Frage 25 von 63

1

Refer to the exhibit. These two routers are configured to run OSPFv3 but they are not forming a neighbor adjacency. What is the cause of the problem?

Wähle eine der folgenden:

The routers do not have global IPv6 addresses that are configured on the Fa0/0 interfaces.
The routers have both been elected as the DR.
The routers are configured with the same router ID.
The routers have the same priority.

Erklärung

Frage 26 von 63

1

What is a recommended method of authentication for OSPFv3?

Wähle eine der folgenden:

MD5 authentication
IPsec to secure routing updates
the passive-interface command
a VPN tunnel between each OSPF neighbor adjacency

Erklärung

Frage 27 von 63

1

During verification or troubleshooting of the OPSFv3 configuration on a router, which three parameters are displayed by the show ipv6 ospf interface command? (Choose three.)

Wähle eine oder mehr der folgenden:

the hello and dead intervals
the metric of the route that is attached to the interface
the global unicast IPv6 address of the interface
the number of interfaces in the area
the OSPFv3 area that the interface is in
the process ID that is assigned to the interface

Erklärung

Frage 28 von 63

1

Refer to the exhibit. What can be concluded about network 192.168.4.0 in the R2 routing table?

Wähle eine der folgenden:

This network should be used to forward traffic toward external networks.
The network was learned from a router within the same area as R2.
The network was learned through summary LSAs from an ABR.
The network can be reached through the GigabitEthernet0/0 interface.

Erklärung

Frage 29 von 63

1

Refer to the exhibit. What is indicated by the O IA in the router output?

Wähle eine der folgenden:

The route was learned from within the area.
The route was learned from outside the internetwork.
The route was manually configured.
The route was learned from another area.

Erklärung

Frage 30 von 63

1

Which statement describes a multiarea OSPF network?

Wähle eine der folgenden:

It has a core backbone area with other areas connected to the backbone area.
It has multiple routers that run multiple routing protocols simultaneously, and each protocol consists of an area.
It consists of multiple network areas that are daisy-chained together.
It requires a three-layer hierarchical network design approach.

Erklärung

Frage 31 von 63

1

A network administrator is implementing OSPF in a portion of the network and must ensure that only specific routes are advertised via OSPF. Which network statement would configure the OSPF process for networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now located in the backbone area, and inject them into the OSPF domain?

Wähle eine der folgenden:

r1(config-router)# network 192.168.0.0 0.0.0.255 area 1
r1(config-router)# network 192.168.4.0 0.0.255.255 area 0
r1(config-router)# network 192.168.4.0 0.0.15.255 area 1
r1(config-router)# network 192.168.0.0 0.0.3.255 area 0
r1(config-router)# network 192.168.4.0 0.0.3.255 area 0
r1(config-router)# network 192.168.4.0 0.0.3.255 area 1

Erklärung

Frage 32 von 63

1

Which two networks are part of the summary route 192.168.32.0/22? (Choose two.)

Wähle eine oder mehr der folgenden:

192.168.35.0/24
192.168.36.0/24
192.168.33.0/24
192.168.31.0/24
192.168.37.0/24
192.168.38.0/24

Erklärung

Frage 33 von 63

1

What routing table descriptor is used to identify OSPF summary networks that originate from an ABR?

Wähle eine der folgenden:

O E1
O E2
O
O IA

Erklärung

Frage 34 von 63

1

A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)

Wähle eine oder mehr der folgenden:

bandwidth
MTU
delay
load
reliability

Erklärung

Frage 35 von 63

1

If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?

Wähle eine der folgenden:

10 seconds
15 seconds
20 seconds
30 seconds

Erklärung

Frage 36 von 63

1

Which EIGRP route would have the preferred administrative distance?

Wähle eine der folgenden:

a summary route
an internal route
an external route that is redistributed from RIP
an external route that is redistributed from OSPF

Erklärung

Frage 37 von 63

1

When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?

Wähle eine der folgenden:

EIGRP authentication
Diffusing Update Algorithm
Reliable Transport Protocol
bounded updates
partial updates

Erklärung

Frage 38 von 63

1

Where are EIGRP successor routes stored?

Wähle eine der folgenden:

only in the routing table
in the routing table and the topology table
only in the neighbor table
in the routing table and the neighbor table

Erklärung

Frage 39 von 63

1

Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?

Wähle eine der folgenden:

show ip protocols
show interfaces
show ip interface brief
show ip route

Erklärung

Frage 40 von 63

1

What information does EIGRP maintain within the routing table?

Wähle eine der folgenden:

only feasible successors
adjacent neighbors
only successors
all routes known to the router
both successors and feasible successors

Erklärung

Frage 41 von 63

1

Which command can be issued on a router to verify that automatic summarization is enabled?

Wähle eine der folgenden:

show ip eigrp neighbors
show ip protocols
show ip interface brief
show ip eigrp interfaces

Erklärung

Frage 42 von 63

1

Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?

Wähle eine der folgenden:

Automatic summarization has been enabled only for the 172.21.100.0/24 network.
Automatic summarization is enabled on neighboring routers.
Automatic summarization is disabled on a per-interface basis.
Automatic summarization is disabled on R3.

Erklärung

Frage 43 von 63

1

Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?

Wähle eine der folgenden:

because the automatic summarization is enabled on R1
because the IPv4 address on Fa0/0 interface of R1 is incorrect
because the Fa0/0 interface of R1 is declared as passive for EIGRP
because there is no network command for the network 192.168.1.0/24 on R1

Erklärung

Frage 44 von 63

1

In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?

Wähle eine der folgenden:

router configuration mode
interface configuration mode
global configuration mode
privileged mode

Erklärung

Frage 45 von 63

1

Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be causing this problem?

Wähle eine der folgenden:

a process ID mismatch
an authentication mismatch
an access list that is blocking advertisements from other networks
automatic summarization that is disabled on both routers

Erklärung

Frage 46 von 63

1

Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?

Wähle eine der folgenden:

The GigabitEthernet 0/1 interface is not participating in the EIGRP process.
The hello timer has been modified on interface GigabitEthernet 0/1 of R3 and not on the neighbor, causing a neighbor adjacency not to form.
The passive-interface command is preventing neighbor relationships on interface GigabitEthernet 0/0.
The GigabitEthernet interfaces are not limiting the flow of EIGRP message information and are being flooded with EIGRP traffic.

Erklärung

Frage 47 von 63

1

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.

What action should be taken to solve this problem?

Wähle eine der folgenden:

Configure the same hello interval between the routers.
Configure EIGRP to send periodic updates.
Enable the serial interfaces of both routers.
Configure both routers with the same EIGRP process ID.

Erklärung

Frage 48 von 63

1

Refer to the exhibit. Which statement is supported by the output?

Wähle eine der folgenden:

The route to 192.168.1.1 represents the configuration of a loopback interface.
A static default route has been manually configured on this router.
A default route is being learned through an external process.
Summarization of routes has been manually configured.

Erklärung

Frage 49 von 63

1

Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?

Wähle eine der folgenden:

The same autonomous system numbers must be used in the interface configurations of each router.
The key string should be used in interface mode instead of the key chain.
The same number of key strings must be used on each router.
The same key chain name must be used on each router.
The authentication configuration is correct, issue the show ip eigrp neighbors command to troubleshoot the issue.

Erklärung

Frage 50 von 63

1

Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?

Wähle eine der folgenden:

ip bandwidth-percent eigrp 100 48
ip bandwidth-percent eigrp 100 75
ip bandwidth-percent eigrp 75 100
ip bandwidth-percent eigrp 64 48
ip bandwidth-percent eigrp 100 64

Erklärung

Frage 51 von 63

1

Which three statements are advantages of using automatic summarization? (Choose three.)

Wähle eine oder mehr der folgenden:

It decreases the number of entries in the routing table.
It reduces the frequency of routing updates.
It ensures that traffic for multiple subnets uses one path through the internetwork.
It maximizes the number of routes in the routing table.
It improves reachability in discontiguous networks.
It increases the size of routing updates.

Erklärung

Frage 52 von 63

1

Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?

Wähle eine der folgenden:

The passive-interface command should have been issued on serial 0/1/0.
The IPv4 address configured on the neighbor that is connected to R1 serial 0/1/0 is incorrect.
The hello interval has been altered on serial 0/1/0 and is preventing a neighbor relationship from forming.
The network statement used for EIGRP 55 does not enable EIGRP on interface serial 0/1/0.
The networks that are configured on serial 0/0/0 and serial 0/1/0 of router R1 are overlapping.

Erklärung

Frage 53 von 63

1

What is a characteristic of manual route summarization?

Wähle eine der folgenden:

requires high bandwidth utilization for the routing updates
has to be configured globally on the router
reduces total number of routes in routing tables
cannot include supernet routes

Erklärung

Frage 54 von 63

1

Refer to the exhibit. A network administrator has issued the shown commands. The EIGRP routing domain has completely converged and a network administrator is planning on configuring EIGRP authentication throughout the complete network. On which two interfaces should EIGRP authentication be configured between R2 and R3? (Choose two.)

Wähle eine oder mehr der folgenden:

gig 0/0 of R3
serial 0/1/0 of R4
serial 0/1/0 of R2
serial 0/0/1 of R2
serial 0/0/1 of R3

Erklärung

Frage 55 von 63

1

Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.)

Wähle eine oder mehr der folgenden:

172.16.3.0/24
172.16.0.0/16
192.168.10.0/24
192.168.10.0/30
192.168.1.0/30

Erklärung

Frage 56 von 63

1

Refer to the exhibit. Router CiscoVille has been partially configured for EIGRP authentication. What is missing that would allow successful authentication between EIGRP neighbors?

Wähle eine der folgenden:

The CiscoVille router requires a second keychain to function correctly when using two interfaces for EIGRP authentication.
The keychain for EIGRP authentication must be configured on the interfaces.
A username and password must be configured.
The interfaces that will use EIGRP authentication must be specified.

Erklärung

Frage 57 von 63

1

Beginning with the Cisco IOS Software Release 15.0, which license is a prerequisite for installing additional technology pack licenses?

Wähle eine der folgenden:

UC
IPBase
SEC
DATA

Erklärung

Frage 58 von 63

1

What statement describes a Cisco IOS image with the “universalk9_npe” designation for Cisco ISR G2 routers?

Wähle eine der folgenden:

It is an IOS version that, at the request of some countries, removes any strong cryptographic functionality.
It is an IOS version that provides only the IPBase feature set.
It is an IOS version that offers all of the Cisco IOS Software feature sets.
It is an IOS version that can only be used in the United States of America.

Erklärung

Frage 59 von 63

1

Which command is used to configure a one-time acceptance of the EULA for all Cisco IOS software packages and features?

Wähle eine der folgenden:

license save
license accept end user agreement
show license
license boot module module-name

Erklärung

Frage 60 von 63

1

How long is the evaluation license period for Cisco IOS Release 15.0 software packages?

Wähle eine der folgenden:

30 days
15 days
60 days
180 days

Erklärung

Frage 61 von 63

1

Which IOS 12.4 software package integrates full features, including voice, security, and VPN capabilities, for all routing protocols?

Wähle eine der folgenden:

Service Provider Services
Advanced Enterprise Services
Advanced Security
Advanced IP Services

Erklärung

Frage 62 von 63

1

When a customer purchases a Cisco IOS 15.0 software package, what serves as the receipt for that customer and is used to obtain the license as well?

Wähle eine der folgenden:

Product Activation Key
Unique Device Identifier
Software Claim Certificate
End User License Agreement

Erklärung

Frage 63 von 63

1

The customer of a networking company requires VPN connectivity for workers who must travel frequently. To support the VPN server, the customer router must be upgraded to a new Cisco IOS software version with the Advanced IP Services feature set. What should the field engineer do before copying the new IOS to the router?

Wähle eine der folgenden:

Issue the show version and the show flash commands to ensure that the router has enough memory and file space to support the new IOS image.
Set the router to load the new IOS image file directly from the TFTP server on the next reboot.
Delete the currently installed IOS by using the erase flash: command, and reload the router
Issue the show running-configuration command to determine the features of the currently installed IOS image file.

	Erstellt von th1rt33n_tony vor fast 9 Jahre

CCNA Practice Quiz

CCNA 3 Practice Quiz

Frage 1 von 63

Which technology is required when switched networks are designed to include redundant links?

Wähle eine der folgenden:

Erklärung

Frage 2 von 63

Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?

Wähle eine der folgenden:

Erklärung

Frage 3 von 63

Which statement describes a characteristic of Cisco Meraki switches?

Wähle eine der folgenden:

Erklärung

Frage 4 von 63

If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?

Wähle eine der folgenden:

Erklärung

Frage 5 von 63

What is a characteristic of a Layer 2 loop?

Wähle eine der folgenden:

Erklärung

Frage 6 von 63

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 7 von 63

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 8 von 63

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Wähle eine der folgenden:

Erklärung

Frage 9 von 63

What is an advantage of using LACP?

Wähle eine der folgenden:

Erklärung

Frage 10 von 63

Which command will initiate EtherChannel interface configuration mode?

Wähle eine der folgenden:

Erklärung

Frage 11 von 63

Which PAgP mode combination will establish an EtherChannel?

Wähle eine der folgenden:

Erklärung

Frage 12 von 63

When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?

Wähle eine der folgenden:

Erklärung

Frage 13 von 63

When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?

Wähle eine der folgenden:

Erklärung

Frage 14 von 63

What type of wireless antenna is best suited for providing coverage in large open spaces, such as hallways or large conference rooms?

Wähle eine der folgenden:

Erklärung

Frage 15 von 63

During which stage of establishing connectivity between a WLAN client and an AP does the client learn the MAC address of the AP?

Wähle eine der folgenden:

Erklärung

Frage 16 von 63

A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?

Wähle eine der folgenden:

Erklärung

Frage 17 von 63

Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

Wähle eine oder mehr der folgenden:

Erklärung

Frage 18 von 63

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

Wähle eine der folgenden:

Erklärung

Frage 19 von 63

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

Wähle eine der folgenden:

Erklärung

Frage 20 von 63

Wähle eine oder mehr der folgenden: