SB&W: Exam CH 1 & 2

Which statement describes a characteristic of Cisco Meraki switches?

Which design feature will limit the size of a failure domain in an enterprise network?

Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration. From privileged EXEC mode, which of the following commands can the administrator use for this purpose? (Choose two.)

What is the function of PoE pass-through?

A network administrator is planning redundant devices and cabling in a switched network to support high availability. Which benefit will implementing the Spanning Tree Protocol provide to this design?

What are two ways to access a Cisco switch for out-of-band management? (Choose two.)

What are two functions of a router? (Choose two.)

In which situation would a network administrator install a Cisco Nexus Series or Cisco Catalyst 6500 Series switch to promote infrastructure scalability?

What are two benefits of extending access layer connectivity to users through a wireless medium? (Choose two.)

What network design would contain the scope of disruptions on a network should a failure occur?

Which two requirements must always be met to use in-band management to configure a network device? (Choose two.)

What term is used to express the thickness or height of a switch?

In the Cisco Enterprise Architecture, which two functional parts of the network are combined to form a collapsed core design? (Choose two.)

How can an enterprise network be designed to optimize bandwidth?

Which statement describes a characteristic of Cisco Catalyst 2960 switches?

A network engineer is reviewing a network design that uses a fixed configuration enterprise router that supports both LAN and WAN connections. However, the engineer realizes that the router does not have enough interfaces to support growth and network expansion. Which type of device should be used as a replacement?

What is the function of ASICs in a multilayer switch?

Refer to the exhibit. Which devices exist in the failure domain when switch S3 loses power?

Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent up-time? (Choose two.)

As the network administrator you have been asked to implement EtherChannel on the corporate network. What does this configuration consist of?

Fill in the blank. Use a number. The default hello timer value for STP BPDU frames is [blank_start]2[blank_end] seconds.

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?

Refer to the exhibit. Which protocol information is being displayed in the output?

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

Which three components are combined to form a bridge ID?

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Which two concepts relate to a switch port that is intended to have only end devices attached and intended never to be used to connect to another switch? (Choose two.)

What is an advantage of PVST+?

To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

Fill in the blank. Do not abbreviate. To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode [blank_start]rapid-pvst[blank_end] global configuration mode command is required

Which is the default STP operation mode on Cisco Catalyst switches?

What additional information is contained in the 12-bit extended system ID of a BPDU?

What value determines the root bridge when all switches connected by trunk links have default STP configurations?

Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?

What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths?

Which STP priority configuration would ensure that a switch would always be the root switch?

Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?

Fill in the blank. In FHRP operation, two or more routers are represented as a single [blank_start]virtual[blank_end] router.