Frage 1
Frage
Which two protocol choices do you have you are implementing an etherChannel bundle? (Choose two).
Antworten
-
A_ PAgP
-
B_ PAgD
-
C_ LACP
-
D_ LAPD
Frage 2
Frage
Which two criteria does EIGRP use, by default to calculate its metric? (Chose two).
Antworten
-
Bandwidth
-
Reliability
-
Load
-
MTU
-
Delay
Frage 3
Frage
All of these tables are maintained by a link-state routing protocol, except which table?
Antworten
-
Routing
-
Topology
-
Update
-
neighbor
Frage 4
Frage
Which OSFP packet helps form neighbor adjacencies?
Frage 5
Frage
Which criterion does SFT use to determine the bets path?
Frage 6
Frage
What is the purpose of LCP?
Antworten
-
to perform authentication
-
to negotiate control options
-
to encapsulate multiple protocols
-
to specify asynchronous versus synchronous
Frage 7
Frage
What are two types of VPNs? (Choose two)
Antworten
-
Remote-access
-
remote-to-site
-
remote-to-remote
-
Site-to-site
Frage 8
Frage
Which two commands could you use to verify that a GRE tunnel is UP (Choose two)
Antworten
-
show ip interface brief
-
show interface tunnel
-
show gre tunnel
-
show tunnel interface
Frage 9
Frage
Witch Cisco router components is used primary to store the startup-config file?
Antworten
-
RAM
-
ROM
-
FLASH MEMORY
-
CONFIGURATION REGISTER
-
NVRAM
Frage 10
Frage
Which port marks the lowest-cost path from the non-root bridge to the root bridge?
Antworten
-
Root
-
blocking
-
designated
-
no designated
Frage 11
Frage
Which switch provides the spanning-tree designated port role the network segment that services the printers?
Antworten
-
switch 1
-
switch 2
-
switch 3
-
switch 4
Frage 12
Frage
Given the output shown from this Cisco 2950, what is the reason that interface FastEthernet 0/10 is not root port for VLAN 2?
Antworten
-
this switch has more than one interface connected to the root network segment in VLAN 2.
-
this switch is running RSTP while the elected designated switch is running 802 1d Spanning Tree.
-
this switch interface has a higher path cost to the root bridge than another in the topology
-
this switch has a lower bridge ID for VLAN 2 than the elected designated switch.
Frage 13
Frage
Which two these statements regarding RSTP are correct? (choose two)
Antworten
-
RSTP cannot operate with PVST
-
RSTP defines new port roles
-
RSTP defines no new port states
-
RSTP is a proprietary implementation of IEEE 802 1D STP
-
RSTP is compatible witch the original IEEE 802 1D STP
Frage 14
Frage
Which port state is introduced by Rapid-PVST?
Antworten
-
learning
-
listening
-
discarding
-
forwarding
Frage 15
Frage
Which two states are the port states when RSTP has converged? (choose two)
Antworten
-
discarding
-
listening
-
learning
-
forwarding
-
disabled
Frage 16
Frage
disabled16. Al which layer of the OSI model is RSTP used to prevent loops?
Antworten
-
physical
-
data link
-
network
-
transport
Frage 17
Frage
What is one benefit of PVST + ?
Antworten
-
PVST + supports Layer 3 load balancing without loops.
-
PVST + reduces the CPU cycles for all the switches in the network.
-
PVST + allows the root switch location to be optimized per VLAN.
-
PVST + automatically selects the root bridge location, to provide optimized bandwidth usage.
Frage 18
Frage
18. Which three statements are typical characteristics of VLAN arrangements? (choose three)
Antworten
-
A new switch has no VLANs configured.
-
Connectivity between VLANs requires a layer 3 device
-
VLANs typically decrease the number of collision domains
-
Each VLAN uses a separate address space
-
A switch maintains a separate bridging table for each VLAN
-
VLANs Cannot span multiples switches
Frage 19
Frage
Refer to the exhibit.
A Technician has configured the Fast Ethernet 0/1 interface on SW11 as an access link in VLAN 1
Based on the output from the show VLAN brief command issued on SW12. What will be the result of making this change on SW11?
Antworten
-
Only the host in VLAN 1 on the two switches will be able to communicate with each other
-
The host in all VLANs on the two switches will be able to communicates witch each other
-
Only the host in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other.
-
Host will not be able to communicate between the two switches.
Frage 20
Frage
What can be done to secure the virtual terminal interfaces on a router? (choose two)
Antworten
-
Administratively shut down the interface
-
Physically secure the interface
-
create an access list and apply it to the virtual terminal with the access-group command
-
configure a virtual terminal password and login process
-
Enter an access test apply it to the virtual terminal interfaces using the access-class command.
Frage 21
Frage
What are three characteristics of the OSPF routing protocol? (choose three)
Antworten
-
It converges quickly
-
OSPF is a classfull routing protocol
-
it uses cost to determine the best route
-
it uses the DUAL algorithm to determine the best route
-
OSPF routers send the complete routing table to all directly attached routers
-
OSPF routers discover neighbors before exchanging routing information
Frage 22
Frage
Which statement is true, as relates to class or classless routing?
Antworten
-
classfull routing protocol send the subnet mask in routing updates.
-
RIPv1 and OSPF are classless routing protocols
-
automatic summarization at classful boundaries can cause problems on discontinuous subnets.
-
EIGRP and OSPF are classful routing protocols and summarize routes by default
Frage 23
Frage
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
Antworten
-
Bandwidth
-
bandwidth and delay
-
bandwidth, Delay, and MTU
-
bandwidth, MTU, Reliability, Delay, and Load
Frage 24
Frage
Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?
Antworten
-
hop count
-
administrative distance
-
link bandwidth
-
link delay
-
link cost
Frage 25
Frage
Which two are advantages of static routing when compared to dynamic routing (choose two)
Antworten
-
configuration complexity decreases as network size increases.
-
Security increases because only the network administrator may change the routing table.
-
Route summarization is computed automatically by the router.
-
Routing tables adapt automatically to topology changes.
-
an efficient algorithm is used to build routing tables, using automatic updates
-
routing updates are automatically to topology changes.
-
routing traffic load is reduced when used in stub network links
Frage 26
Frage
Which command are required to property configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (choose two)
Antworten
-
Router(config)# router ospf 0
-
Router(config)# router ospf 1
-
Router(config)# router ospf area 0
-
Router(config-router)#network 192.168.16.0 0.0.0.255 0
-
Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
-
Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Frage 27
Frage
Which command enables IPv6 forwarding on a cisco router?
Antworten
-
ipv6 local
-
ipv6 host
-
ipv6 unicast-routing
-
ipv6 neighbor
Frage 28
Frage
Which two option are valid WAN connectivity methods? (choose two)
Antworten
-
PPP
-
WAP
-
DSL
-
L2TPv3
-
Ethernet
Frage 29
Frage
What are two characteristics of frame relay point-to point sub interfaces? (choose two)
Antworten
-
they create split-horizon issues
-
they require a unique subnet within a routing domain
-
they emulate leased lines
-
they are ideal for full-mesh topologies
-
they require the use of NBMA options when using OSPF
Frage 30
Frage
Which two statements about using the CHAP authentication mechanism in a PPP link are true? (choose two)
Antworten
-
CHAP uses a two-way handshake
-
CHAP uses a three-way handshake
-
CHAP authentication periodically occurs after link establishment
-
CHAP authentication passwords are sent in plaintext
-
CHAP authentication is performed only upon link establishment
-
CHAP has no protection from playback attacks
Frage 31
Frage
Which command allows you to verify the encapsulation type (CISCO or IETF) for a frame Relay link?
Antworten
-
Show frame-relay lmi
-
Show frame-relay map
-
Show frame-relay pvc
-
Show interfaces serial