9814737
Beschreibung
Quiz von Kessi Silva, aktualisiert more than 1 year ago
|
Erstellt von Kessi Silva
vor fast 7 Jahre
|
|
Frage 1
Frage
1. In the accompanying graphic, what is the name for the section of the MAC address marked as unknown?
Antworten
-
IOS
-
OSI
-
ISO
-
OUI
Frage 2
Frage
__________on an Ethernet network is the retransmission delay that’s enforced when a collision occurs.
Antworten
-
Backoff
-
Carrier sense
-
Forward delay
-
Jamming
Frage 3
Frage
On which type of device could the situation shown in the diagram occur?
Antworten
-
Hub
-
Switch
-
Router
-
Bridge
Frage 4
Frage
In the Ethernet II frame shown here, what is the function of the section labeled “FCS”?
Antworten
-
Allows the receiving devices to lock the incoming bit stream.
-
Error detection
-
Identifies the upper-layer protocol
-
Identifies the transmitting device
Frage 5
Frage
A network interface port has collision detection and carrier sensing enabled on a shared twisted-pair network. From this statement, what is known about the network interface port?
Antworten
-
This is a 10 Mbps switch port.
-
This is a 100 Mb/s switch port.
-
This is an Ethernet port operating at half-duplex.
-
This is an Ethernet port operating at full-duplex.
-
This is a port on a network interface card in a PC.
Frage 6
Frage
For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)
Antworten
-
To uniquely identify devices at layer 2
-
To allow communication with devices on a different network
-
To differentiate a layer 2 frame from a layer 3 packet
-
To establish a priority system to determine which device gets to transmit first
-
To allow communication between different devices on the same network
-
To allow detection of a remote device when its physical address is unknown
Frage 7
Frage
Between which systems could you use a cable that uses the pinout pattern shown here?
Antworten
-
With a connection from a switch to a switch
-
With a connection from a router to a router
-
With a connection from a host to a host
-
With a connection from a host to a switch
Frage 8
Frage
In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)
Antworten
-
When they receive a special token
-
When there is a carrier
-
When they detect that no other devices are sending
-
When the medium is idle
-
When the server grants access
Frage 9
Antworten
-
Fiber optic
-
Crossover Gigabit Ethernet cable
-
Straight-through Fast Ethernet
-
Coaxial
Frage 10
Frage
When configuring a terminal emulation program, which of the following is an incorrect setting?
Antworten
-
Bit rate: 9600
-
Parity: None
-
Flow control: None
-
Data bits: 1
Frage 11
Frage
Which part of a MAC address indicates whether the address is a locally or globally administered address?
Antworten
-
FCS
-
I/G bit
-
OUI
-
U/L bit
Frage 12
Frage
What cable type uses the pinout arrangement shown below?
Antworten
-
Fiber optic
-
Rolled
-
Straight-through
-
Crossover
Frage 13
Frage
Which of the following is not one of the actions taken in the operation of CSMA/CD when a collision occurs?
Antworten
-
A jam signal informs all devices that a collision occurred.
-
The collision invokes a random backoff algorithm on the systems involved in the collision.
-
Each device on the Ethernet segment stops transmitting for a short time until its backoff timer expires.
-
All hosts have equal priority to transmit after the timers have expired.
Frage 14
Frage
Which of the following statements is false with regard to Ethernet?
Antworten
-
There are very few collisions in full-duplex mode.
-
A dedicated switch port is required for each full-duplex node.
-
The host network card and the switch port must be capable of operating in full-duplex mode to use full-duplex.
-
The default behavior of 10Base-T and 100Base-T hosts is 10 Mbps half-duplex if the autodetect mechanism fails.
Frage 15
Frage
In the following diagram, identify the cable types required for connections A and B.
Antworten
-
A= crossover, B= crossover
-
A= crossover, B= straight-through
-
A= straight-through, B= straight-through
-
A= straight-through, B= crossover
Frage 16
Frage
In the following image, match the cable type to the standard with which it goes.
1000Base-T ::::: IEEE 802.3u
1000Base-SX ::: IEEE 802.3
10Base-T ::::::::: IEEE 802.3ab
100Base-TX ::::: IEEE 802.3z
Antworten
-
IEEE 802.3u ::::::: 100Base-Tx IEEE 802.3 ::::::::: 10Base-T IEEE 802.3ab ::::: 1000Base-T IEEE 802.3z ::::::: 1000Base-SX
-
IEEE 802.3u :::::::1000Base-T IEEE 802.3 ::::::::: 10Base-T IEEE 802.3ab ::::: 100Base-Tx IEEE 802.3z ::::::: 1000Base-SX
-
IEEE 802.3u ::::::: 1000Base-SX IEEE 802.3 ::::::::: 10Base-T IEEE 802.3ab ::::: 1000Base-T IEEE 802.3z ::::::: 100Base-Tx
-
IEEE 802.3u ::::::: 1000Base-SX IEEE 802.3 ::::::::: 1000Base-T IEEE 802.3ab ::::: 10Base-T IEEE 802.3z ::::::: 100Base-Tx
Frage 17
Frage
The cable used to connect to the console port on a router or switch is called a _________cable.
Antworten
-
Crossover
-
Rollover
-
Straight-through
-
Full-duplex
Frage 18
Frage
Which of the following items does a socket comprise?
Antworten
-
IP address and MAC address
-
IP address and port number
-
Port number and MAC address
-
MAC address and DLCI
Frage 19
Frage
Which of the following hexadecimal numbers converts to 28 in decimal?
Antworten
-
1c
-
12
-
15
-
ab
Frage 20
Antworten
-
Fiber optic
-
Rollover
-
Coaxial
-
Full-duplex
Möchten Sie mit GoConqr kostenlos Ihre eigenen Quiz erstellen? eigenen Mehr erfahren.