Electronics Ch. 4

Description

Flashcards for Chapter 4
Matthew Kendall
Flashcards by Matthew Kendall, updated more than 1 year ago
Matthew Kendall
Created by Matthew Kendall over 6 years ago
660
0

Resource summary

Question Answer
If N1/N2=4 and the primary voltage is 120 V, what is the secondary voltage? B. 30 V
In a step down transformer, which is larger? A. Primary Voltage
A transformer has a turns ratio of 2:1. What is the peak secondary voltage if 115 Vrms is applied to the primary winding? B. 81.3 V
With a half-wave rectified voltage across the load resistor, load current flows for what part of a cycle? C. 180 Degrees
Suppose line voltage may be as low as 105 Vrms or as high as 125 Vrms in a half-wave rectifier. With a 5:1 step-down transformer, the minimum peak load voltage is closest to C. 29.7 V
The voltage out of a bridge rectifier is a: D. Sine wave
If the line voltage is 115 Vrms, a turns ratio of 5:1 means the rms secondary voltage is closest to: D. 35 V
What is the peak load voltage in a full-wave rectifier if the secondary voltage is 20 Vrms? C. 14.1 V
We want a peak load voltage of 40 V out of a bridge rectifier. What is the approximate rms value of the secondary voltage? C. 28.3 V
With a full-wave rectified voltage across the load resistor, load current flows for what part of a cycle? D. 360 degrees
What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 Vrms? (Use second approximation) B. 16.4 V
If line frequency is 60 Hz, the output frequency of a half-wave rectifier is B. 60 Hz
If line frequency is 60 Hz, the output frequency of a bridge rectifier is C. 120 Hz
With the same secondary voltage and filter, which has the most ripple? A. Half-wave rectifier
With the same secondary voltage and filter, which produces the least load voltage? B. Full-wave rectifier
If the filtered load current is 10 mA, which of the following has a diode current of 10 mA? A. Half-wave rectifier
If the load current is 5 mA and the filter capacitance is 1000 uF, what is the peak to pear ripple out of a bridge rectifier? D. 41.7 mV
The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. This means the dc load current can have a maximum value of C. 4 A
What is the PIV across each diode of a bridge rectifier with a secondary voltage of 20 Vrms? C. 28.3 V
If the secondary voltage increases in a bridge rectifier with a capacitor-input filter, the load voltage will C. Increase
If the filter capacitance is increased, the ripple will A. Decrease
A circuit that removes positive or negative parts of a waveform is called a B. Clipper
A circuit that adds a positive or negative dc voltage to an input sine wave is called a A. Clamper
For a clamper circuit to operate properly, its RLC time constant should be C. >100 times the period T of the signal
Voltage multipliers are circuits best used to produce C. High Voltage and low Current
Show full summary Hide full summary

Similar

Plant Structure and Photosynthesis
mckenziedev
Food Vocabulary Quiz
Liz Bartik
Physics GCSE AQA Unit 1 quiz
Adorkable_dreamer
A-level Maths: Key Differention Formulae
humayun.rana
GCSE History – The early years and the Weimar Republic 1918-1923
Ben C
Matematica para concursos
Luiz Ricardo Oliveira
TItrations (how to do the experiment) (concentrations)
janey.efen
CCNA Security 210-260 IINS - Exam 2
Mike M
Macbeth Key Quotes
Draco Malfoy
Mapa Conceptual
Julio Perez