12284989
Description
Mind Map by Kieran Lancaster, updated more than 1 year ago
|
Created by Kieran Lancaster
almost 7 years ago
|
|
CHP 9 - Energy, Power and Resistance Pt1
- Circuit symbols
- A battery is two or more cells put together.
The longer end represents the positive
terminal, the short represents negative
- A battery is two or more cells put together.
The longer end represents the positive
terminal, the short represents negative
- P.d and E.M.F
- One Volt is the p.d across a component when 1J of
energy is transferred per unit charge
- 1V=1JC^-1
- P.d is work done by the charge carriers per unit of charge. The difference in
energy before and after a point. Electrical energy transferred into other forms.
- 1V=1JC^-1
- E.m.f is work done on the charge carriers per unit charge, by
a cell or battery. The charge carriers gain electrical energy
- The formula is
the same as the
one above
- The formula is
the same as the
one above
- One Volt is the p.d across a component when 1J of
energy is transferred per unit charge
- The electron gun
- A small metal filament is heated until some elctrons get
enough kinetic energy to escape the surface of the metal,
in a process called thermionic emission.
- This is placed in a vacuum, with a high, accelerating
p.d between the cathode and anode
- The freed electrons are accelerated towards the anode, gaining
- If there is a small hole in the anode, a fine beam of electrons is created.
- If there is a small hole in the anode, a fine beam of electrons is created.
- The freed electrons are accelerated towards the anode, gaining
- This is placed in a vacuum, with a high, accelerating
p.d between the cathode and anode
- As electrons accelerate, they gain kinetic energy.
P.d=eV, V being the accelerating p.d.
- Work done on electron = gain in kinetic energy
- eV=1/2mv^2
- eV=1/2mv^2
- Work done on electron = gain in kinetic energy
- A small metal filament is heated until some elctrons get
enough kinetic energy to escape the surface of the metal,
in a process called thermionic emission.
- Resistance
- Resistance is the ratio of p.d
Across a component/current
in a component
- The unit is the ohm, were 1Ω=1VA⁻¹
- The unit is the ohm, were 1Ω=1VA⁻¹
- Ohms law states: For a conductor kept at a
constant temperature, current in the wire is
proportional to the p.d across it
- When a wire gets hotter, resistance increases and therefore current
decreases. This is because positive ions vibrate with a greater
amplitude, increasing the frequency of the collisions. The electrons
transfer more energy, which is given off as heat.
- When a wire gets hotter, resistance increases and therefore current
decreases. This is because positive ions vibrate with a greater
amplitude, increasing the frequency of the collisions. The electrons
transfer more energy, which is given off as heat.
- Resistance is the ratio of p.d
Across a component/current
in a component
- I-V characteristics
- The circuit shown left is used to
collect data for an I/V graph, but the
fixed resistor can be any component
- A filament lamp is non ohmic, since p/d
isnt proportional to Current. The
resistance of the lamp is also not constant
- Resistance increases as the p.d across it increases, since
the wire increases with temperature until it glows.
- Resistance increases as the p.d across it increases, since
the wire increases with temperature until it glows.
- A filament lamp is non ohmic, since p/d
isnt proportional to Current. The
resistance of the lamp is also not constant
- Fixed resistors have constant resistance, regardless
of temperature. Voltage is proportional to
temperature, therefore they follow ohms law
- Shallower line = higher resistance, since
R=Inverse of gradient (R=V/I, not I/V)
- Shallower line = higher resistance, since
R=Inverse of gradient (R=V/I, not I/V)
- The circuit shown left is used to
collect data for an I/V graph, but the
fixed resistor can be any component
- Diodes
- A diode only allows current to flow in one particular
direction (shown by the way the 'arrow' faces)
- Some diodes are light emitting diodes, shown
by two arrows. They function the same way as
normal diodes, but light up when current flows
- A diode is non ohmic, and it's behaviour depends on the polarity
- A diode is non ohmic, and it's behaviour depends on the polarity
- Some diodes are light emitting diodes, shown
by two arrows. They function the same way as
normal diodes, but light up when current flows
- The I/V graph for a diode is shown left. When p.d
is negative, resistance is almost infinite. No
current can flow the wrong way through a diode
- When positive, current doesn't flow initially. A
threshold p.d has to be reached (this is the point
and L.E.D starts emitting light, the threshold p.d
determines the colour/frequency of light)
- From this point, for every small increase in p.d,
resistance drops sharply.
- From this point, for every small increase in p.d,
resistance drops sharply.
- When positive, current doesn't flow initially. A
threshold p.d has to be reached (this is the point
and L.E.D starts emitting light, the threshold p.d
determines the colour/frequency of light)
- A diode only allows current to flow in one particular
direction (shown by the way the 'arrow' faces)
Media attachments
Want to create your own Mind Maps for free with GoConqr? Learn more.