Unit 203 Revision: Installation Technology Question Bank No.1

1

A BS3036 protective device is a

1

A circuit supplying kitchen appliances would be identified as

1

A circuit to supply hot water would be identified as

1

A common method of providing protection by fault protection

1

A method of protection against electric shock is provided in a cable by

1

A work plan for new installations provides:

1

A requirement for safety that all installations should have is

1

A short circuit occurs

1

A single pole switch breaks

1

A typical system application for fibre optic cable is:

1

A voltage of 400kV represents the following voltage

1

Aluminium may be used as a conductor in preference to copper as it is

1

Aluminium spiral fixings are used to fix items on

1

An Earthing system that uses a separate conductor as a return path for any fault current is called

1

An example of overload is

1

An RCD is a device used to protect circuits against

1

Automatic disconnection of supply and special locations are found in

1

Best location for a solar panel

1

BS 3036 Fuses

1

Circuit breakers are frequently installed in preference to fuses because

1

Circuit breakers use two forms of operation

1

Define the term for a Circuit Protective Conductor (CPC)

1

Determine the size of conduit required for a run of 2.7m, if you are installing 3 x 1.5mm² and 6 x 6mm² conductors (all stranded).

1

Determine the size of conduit required for a run of 2.9m, if you are installing 9 x 2.5mm² and 3 x 6mm² conductors (all stranded).

1

Equipment identified in BS 7671 by an EN number must comply with the relevant requirements of:

1

ES lamp holders, the outer casing must be connected to

1

Excess current, flowing in a circuit which is electrically sound, is defined as

1

From BS 7671 the disconnection time for circuits supplying equipment and circuits up to 32A is :

1

What does Ze represent from the following formula Zs = Ze + (R1 + R2)?

1

What does R1 represent from the following formula Zs = Ze + (R1 + R2)?

1

From the On-site-Guide the maximum external earth loop impedance for a TN-C-S system is?

1

From the On-site-Guide the maximum external earth loop impedance for a TN-S system is?

1

Holes between joists must be of a minimum distance from top or bottom fixing surface of

1

Identify the distribution voltage for a large story building with a private transformer

1

IET Wiring regulations give directives on electrical installations in hazardous environments, however the statutory governing these situations are covered in the:

1

IET Wiring regulations apply particularly to:

1

IET Wiring regulations recommend inspection of temporary construction site installation every:

1

If a 20mm steel conduit was to be installed horizontally what would be the maximum spacing of supports

1

If a 30A fuse has a tripping characteristic of 5 x In, what would be the instantaneous tripping current?

1

A cable has resistance of 0.12 ohms and a current of 30A. The volt drop due to resistance is

C&G 2365 Level 2 Unit 203 Revision OB

Unit 203 Revision: Installation Technology Question Bank No.1

Unit 203 Revision: Installation Technology Question Bank No.1

A BS3036 protective device is a

A circuit supplying kitchen appliances would be identified as

A circuit to supply hot water would be identified as

A common method of providing protection by fault protection

A method of protection against electric shock is provided in a cable by

A work plan for new installations provides:

A requirement for safety that all installations should have is

A short circuit occurs

A single pole switch breaks

A typical system application for fibre optic cable is:

A voltage of 400kV represents the following voltage

Aluminium may be used as a conductor in preference to copper as it is

Aluminium spiral fixings are used to fix items on

An Earthing system that uses a separate conductor as a return path for any fault current is called

An example of overload is

An RCD is a device used to protect circuits against

Automatic disconnection of supply and special locations are found in

Best location for a solar panel

BS 3036 Fuses