PDD Quiz XII

Question 1 of 20

1

Which of the following are the advantages of using plastic pipes in plumbing systems? 𝗖𝗵𝗼𝗼𝘀𝗲 𝘁𝗵𝗲 𝗳𝗼𝘂𝗿 𝘁𝗵𝗮𝘁 𝗮𝗽𝗽𝗹𝘆.

Select one or more of the following:

Plastic pipes can be easily joined.
Plastic pipes can be used exposed due to their resistance to ultraviolet radiation.
Plastic pipes cost less compared to copper piping.
Plastic pipes produce low friction.
All plastic pipes are suitable for delivering drinking water.
Plastic pipes don't have the risk of corrosion.

Explanation

Question 2 of 20

1

Which of the following lumber thickness below is more likely to be a 𝘥𝘪𝘮𝘦𝘯𝘴𝘪𝘰𝘯𝘢𝘭 𝘭𝘶𝘮𝘣𝘦𝘳?

Select one of the following:

1"
3"
5"
8"

Explanation

Question 3 of 20

1

What is the maximum recommended cavity space width in a typical brick veneer wall?

Select one of the following:

2"
3"
3 1/2"
4 1/2"

Explanation

Question 4 of 20

1

What are the required hours of fire separation in a floor assembly between a 2300 square foot fully sprinklered food processing facility on the second floor and a fully sprinklered private garage on the first floor of a 2-story building?

https://codes.iccsafe.org/content/IBC2021P2

Select one of the following:

No separation required
Not permitted
1 Hour
2 Hours

Explanation

Question 5 of 20

1

Drag and drop the given components of the schematic door elevation across the highlighted letters given below accordingly. Not all of the given components are relevant to the given elevation detail.

Drag an answer into the correct orange point.

Top Rail

Lock Stile

Hinge Stile

Lock Rail

Cross Rail

Raised Panel

Muntin

Bottom Rail

Explanation

Question 6 of 20

1

An architect is red-lining the revised furniture plan of the building amenities floor of a residential apartment. He notices that the interior designer missed updating GL-FURN-1 as GL-FURN1A in new plans and elevations. Which of the following elevations should be revised as well as the plan itself to show the new furniture? 𝘾𝙝𝙚𝙘𝙠 𝙖𝙡𝙡 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

1/D615
2/D615
3/D615
4/D615
5/D615
6/D615
1/D619
2/D619
3/D619
4/D619

Explanation

Question 7 of 20

1

What is the total U value of a 40′ x 60′ foot building with two 8′ x 4′ windows on each 60 feet wall if the height of the walls is 11 feet tall? (R-value of windows = 2, and R-value of the walls = 8.)

https://www.ncarb.org/sites/default/files/ARE5-Handbook.pdf

Select one of the following:

0.132
0.147
0.154
0.167

Explanation

Question 8 of 20

1

An architect is comparing the life-cycle costs of incandescent and CFL lamps for accent lighting in a retail project. Based on the table given below, what is the cost difference per lamp between the two lamp types if the use per lamp is expected to be 60,000 hours during the project's lifetime? (Ignore the long-term energy cost increase)

Select one of the following:

$358.00
$272.00
$325.00
$448.00

Explanation

Question 9 of 20

1

An architect is working on the cost of a retaining wall. She already established the cost of excavation and the 12" tall footing required for this wall as $3,000. She is now calculating the above-ground cost of the retaining wall based on the $20 per square foot unit cost. If the pressure applied by the earth on the given retaining wall below is 25 pounds per cubic foot and the total lateral force applied on the retaining wall is 3200 #-ft, what is the total cost of this 25-foot-long retaining wall?

Select one of the following:

$8,000
$10,050
$10,500
$11,000

Explanation

Question 10 of 20

1

Which of the following door hinge is more likely to be specified for a storage room door where large equipment is moved in and out?

Select one of the following:

Swing Clear
Detention Hinge
Spring Hinges
Anchor Hinges

Explanation

Question 11 of 20

1

Which of the low-slope roofing insulation materials below is superior to the rest regarding; thermal properties, moisture protection, and compatibility with roofing membranes?

Select one of the following:

Extruded polystyrene foam
Expanded polystyrene board
Polyisocyanurate foam
Perlite board

Explanation

Question 12 of 20

1

Which of the following option gives the sections given below in the correct order, from best to worst, based on their resistance to the exterior airborne sound transmission?

Select one of the following:

Section I > Section II > Section III
Section II > Section I > Section III
Section I > Section III > Section II
Section II > Section III > Section I

Explanation

Question 13 of 20

1

Select the functions of "kerf" in wall assemblies. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙬𝙤 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

To create a capillary break at the bottom edge of an exterior surface.
To create room in stone panels to anchor them to the backup wall.
To increase the R-value of the wall assemblies.
To provide room for sealants in wall openings like windows and doors.

Explanation

Question 14 of 20

1

An architect is reviewing some coating options for her new school project with concrete floor finishes. Which of the following coating is more likely to provide a nonskid, waterproof finish for the project?

Select one of the following:

Epoxy coal-tar based coating
Coal-tar-modified epoxy resin coating
Cementitious acrylic polymeric coating
Vinyl-ester based coating

Explanation

Question 15 of 20

1

Select the correct methods to attach the ISO board and cover board to the roofing membrane with a single-ply membrane roofing. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙝𝙧𝙚𝙚 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Fully adhered
Mopping
Mechanically fastened
Ballasted
Torched

Explanation

Question 16 of 20

1

Select the correct statements regarding parapet details. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙛𝙤𝙪𝙧 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

As a coping material, brick is more water-resistant compared to sheet metal copings and works better to shed water away from the parapet wall.
Sheet metal copings are more water-resistant compared to brick copings, so their use is much more common.
In a typical roof parapet detail, metal cleats are used to secure roof flashing and to provide wind resistance.
The coping over a roof parapet is generally sloped away from the roof.
Stone copings over brick parapet walls are secured via steel dowels.
When through-the-wall or surface-mounted counter flashing options are not available, a reglet on the wall can be a solution to secure the counter flashing.
Counter flashings are typically installed under the base flashings to prevent water infiltration.

Explanation

Question 17 of 20

1

Which of the following component is used to transfer shear forces from the diaphragm to beams and shear walls?

Select one of the following:

Hold downs
Drag struts
Post Caps
Mending Plates

Explanation

Question 18 of 20

1

An architect is working on a large high-school project with a complex and unique facade design, so she is considering GFRC panels rather than precast concrete panels on the facade. Which of the following are probably the reasons to justify this choice? 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙝𝙧𝙚𝙚 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

GFRC panels are much lighter, so they are more convenient, especially when complex facade design can bring total building loads to critical levels.
Although precast concrete panels are much more effective in creating complex designs, GFRC is preferred due to its low cost.
GFRC panels have higher resistance to impact compared to precast concrete panels.
Compared to precast panels, GFRC panels are more durable and have a higher tensile strength.
Installation of precast concrete panels is less labor intensive and faster however, GFRC panels are preferred due to their lower material cost.
Since sustainability is not a concern of this project, the architect selected GFRC panels rather than precast panels.

Explanation

Question 19 of 20

1

Which of the following options are typically included in Project Documents? 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙛𝙤𝙪𝙧 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Bidding Requirements
Contract forms, conditions and modifications
Product warranties
Drawing and Specifications
Addendum
Zoning Requirements

Explanation

Question 20 of 20

1

An architect works on a residential project and wants to achieve the highest R-value possible. Which of the following window materials provides a better R-value compared to the rest? 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙬𝙤 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Wood
Vinyl
Steel
Aluminum

	Created by a a 27 days ago

ARCH PDD Quiz on PDD Quiz XII, created by a a on 29/06/2024.

PDD Quiz XII

PDD Quiz XII

Question 1 of 20

Which of the following are the advantages of using plastic pipes in plumbing systems? 𝗖𝗵𝗼𝗼𝘀𝗲 𝘁𝗵𝗲 𝗳𝗼𝘂𝗿 𝘁𝗵𝗮𝘁 𝗮𝗽𝗽𝗹𝘆.

Select one or more of the following:

Explanation

Question 2 of 20

Which of the following lumber thickness below is more likely to be a 𝘥𝘪𝘮𝘦𝘯𝘴𝘪𝘰𝘯𝘢𝘭 𝘭𝘶𝘮𝘣𝘦𝘳?

Select one of the following:

Explanation

Question 3 of 20

What is the maximum recommended cavity space width in a typical brick veneer wall?

Select one of the following:

Explanation

Question 4 of 20

What are the required hours of fire separation in a floor assembly between a 2300 square foot fully sprinklered food processing facility on the second floor and a fully sprinklered private garage on the first floor of a 2-story building? https://codes.iccsafe.org/content/IBC2021P2

Select one of the following:

Explanation

Question 5 of 20

Drag and drop the given components of the schematic door elevation across the highlighted letters given below accordingly. Not all of the given components are relevant to the given elevation detail.

Drag an answer into the correct orange point.

Explanation

Question 6 of 20

Select one or more of the following:

Explanation

Question 7 of 20

What is the total U value of a 40′ x 60′ foot building with two 8′ x 4′ windows on each 60 feet wall if the height of the walls is 11 feet tall? (R-value of windows = 2, and R-value of the walls = 8.) https://www.ncarb.org/sites/default/files/ARE5-Handbook.pdf

Select one of the following:

Explanation

Question 8 of 20

Select one of the following:

Explanation

Question 9 of 20

Select one of the following:

Explanation

Question 10 of 20

Which of the following door hinge is more likely to be specified for a storage room door where large equipment is moved in and out?

Select one of the following:

Explanation

Question 11 of 20

Which of the low-slope roofing insulation materials below is superior to the rest regarding; thermal properties, moisture protection, and compatibility with roofing membranes?

Select one of the following:

Explanation

Question 12 of 20

Which of the following option gives the sections given below in the correct order, from best to worst, based on their resistance to the exterior airborne sound transmission?

Select one of the following:

Explanation

Question 13 of 20

Select the functions of "kerf" in wall assemblies. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙬𝙤 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Explanation

Question 14 of 20

An architect is reviewing some coating options for her new school project with concrete floor finishes. Which of the following coating is more likely to provide a nonskid, waterproof finish for the project?

Select one of the following:

Explanation

Question 15 of 20

Select the correct methods to attach the ISO board and cover board to the roofing membrane with a single-ply membrane roofing. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙝𝙧𝙚𝙚 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Explanation

Question 16 of 20

Select the correct statements regarding parapet details. 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙛𝙤𝙪𝙧 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Explanation

Question 17 of 20

Which of the following component is used to transfer shear forces from the diaphragm to beams and shear walls?

Select one of the following:

Explanation

Question 18 of 20

Select one or more of the following:

Explanation

Question 19 of 20

Which of the following options are typically included in Project Documents? 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙛𝙤𝙪𝙧 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Explanation

Question 20 of 20

An architect works on a residential project and wants to achieve the highest R-value possible. Which of the following window materials provides a better R-value compared to the rest? 𝘾𝙝𝙚𝙘𝙠 𝙩𝙝𝙚 𝙩𝙬𝙤 𝙩𝙝𝙖𝙩 𝙖𝙥𝙥𝙡𝙮.

Select one or more of the following:

Explanation

What are the required hours of fire separation in a floor assembly between a 2300 square foot fully sprinklered food processing facility on the second floor and a fully sprinklered private garage on the first floor of a 2-story building?

https://codes.iccsafe.org/content/IBC2021P2

What is the total U value of a 40′ x 60′ foot building with two 8′ x 4′ windows on each 60 feet wall if the height of the walls is 11 feet tall? (R-value of windows = 2, and R-value of the walls = 8.)

https://www.ncarb.org/sites/default/files/ARE5-Handbook.pdf