TEST

Question 1 of 199

1

You want to gather as much detail as possible during a network audit, to include data time
stamping across a large number of interfaces, customized according to interface, with a minimal
impact on the network devices themselves. Which tool would you use to meet these
requirements?

Select one of the following:

RMON
SNMPv3
NetFlow
Cisco Discovery Protocol

Explanation

Question 2 of 199

1

You want to gather as much detail as possible during a network audit with a minimal impact on the
network devices themselves. Which tool would you use to include data time stamping across a
large number of interfaces while being customized according to each interface?

Select one of the following:

RMON
SNMPv3
NetFlow
Cisco Discovery Protocol

Explanation

Question 3 of 199

1

In which phase of PPDIOO are the network requirements identified?

Select one of the following:

Design
Plan
Prepare
Implement
Operate
Optimize

Explanation

Question 4 of 199

1

Which is part of the Prepare phase of PPDIOO?

Select one of the following:

Obtain site contact information
Perform network audit
Identify customer requirements
Perform gap analysis

Explanation

Question 5 of 199

1

When designing the identity and access control portions for the enterprise campus network, which
of these solutions would be the most appropriate solution to consider?

Select one of the following:

802.1X
ACLs in the core layer
Cisco Security MARS
NetFlow

Explanation

Question 6 of 199

1

Which is the purpose of the Cisco NAC Profiler?

Select one of the following:

Automates discovery and inventory of all LAN attached devices
Generates a profile based on username and group
Learns and creates a database of virus definitions based on LAN traffic
A database used to map user VPN accounts

Explanation

Question 7 of 199

1

Cisco Identity-Based Networking Services relies heavily on the 802.1X protocol. Which other
authentication solution is used hand-in-hand with 802.1X to authenticate users for network
access?

Select one of the following:

RADIUS
LEAP
IPsec
TACACS
SAKMP

Explanation

Question 8 of 199

1

Which protocol is used for voice bearer traffic?

Select one of the following:

MGCP
RTP
SCCP
CDP
CMP

Explanation

Question 9 of 199

1

Which protocol is used to reserve bandwidth for the transport of a particular application data flow
across the network?

Select one of the following:

cRTP
IEEE 802.1P
RSVP
LFI
Auto QOS

Explanation

Question 10 of 199

1

Which two features are supported by single wireless controller deployments? (Choose two.)

Select one or more of the following:

automatic detection and configuration of LWAPPs
LWAPP support across multiple floors and buildings
automatic detection and configuration of RF parameters
Layer 2 and Layer 3 roaming
controller redundancy
mobility groups

Explanation

Question 11 of 199

1

Which four services does the architecture for Media Services contain? (Choose four.)

Select one or more of the following:

access services
transport services
storage services
forwarding services
session control services
security services
filtering services
remote access services

Explanation

Question 12 of 199

1

Refer to the exhibit.

Which layer is the distribution layer?

Select one of the following:

Layer A
Layer B
Layer C
Layers A and B form a consolidated core and distribution layer

Explanation

Question 13 of 199

1

Which IPv6 feature enables routing to distribute connection requests to the nearest content
server?

Select one of the following:

Link-local
Site-local
Anycast
Multicast
Global aggregatable

Explanation

Question 14 of 199

1

What is the recommended spanning tree protocol to use for all Layer 2 deployments in a branch
office environment?

Select one of the following:

CST
RSPT
PVST
MISTP
Rapid PVST +

Explanation

Question 15 of 199

1

Refer to the exhibit.

A standard, Layer 2 campus network design is pictured. Which numbered box represents the
distribution layer?

Select one of the following:

#1
#2
#3
#4

Explanation

Question 16 of 199

1

Which two are types of network virtualization? (Choose two.)

Select one or more of the following:

VSS: Virtual Switching System
VRF: virtual routing and forwarding
VCI: virtual channel identifier
VLSM: variable length subnet masking
VM: virtual machine
VMP: Virtual Memory Pool

Explanation

Question 17 of 199

1

You are tasked with designing a new branch office that will support 75 users with possible
expansion in the future and will need a highly available network. Which of the branch design
profiles should be implemented?

Select one of the following:

large branch design
medium branch design
teleworker design
small branch design

Explanation

Question 18 of 199

1

Which two can be used as a branch office WAN solution? (Choose two.)

Select one or more of the following:

frame relay
MPLS
Metro Ethernet
GPRS
dial-up modem
3G USB modems

Explanation

Question 19 of 199

1

What is the acceptable amount of one-way network delay for voice and video applications?

Select one of the following:

300 bytes
1 sec
150 ms
500 ms

Explanation

Question 20 of 199

1

Which mode is used to exclusively look for unauthorized access points?

Select one of the following:

monitor mode
sniffer mode
rogue detector mode
local mode

Explanation

Question 21 of 199

1

Which of the following three options represents the components of the Teleworker Solution?
(Choose three.)

Select one or more of the following:

Cisco Unified IP Phone
Cisco 880 Series Router
Aironet Office Extend Access Point
Catalyst 3560 Series Switch
Cisco 2900 Series Router
MPLS Layer 3 VPN
Leased lines

Explanation

Question 22 of 199

1

Which three types of WAN topologies can be deployed in the Service Provider Module? (Choose
three.)

Select one or more of the following:

ring
star
full mesh
core/edge
collapsed core
partial mesh

Explanation

Question 23 of 199

1

Drag.

Drag an answer into the correct orange point.

Redundant Links

Internet Deployment model

Redundant devices

Private WAN deployment

Redundant Links and Devices

MPLS Deployment Model

Explanation

Question 24 of 199

1

Which statement describes the recommended deployment of DNS and DHCP servers in the Cisco
Network Architecture for the Enterprise?

Select one of the following:

Place the DHCP and DNS servers in the Enterprise Campus Access layer and Enterprise
branch.
Place the DHCP and DNS servers in the Enterprise Campus Server Farm layer and Enterprise
branch.
Place the DHCP server in the Enterprise Campus Core layer and Remote Access_VPN module
with the DNS server in the Internet Connectivity module.
Place the DHCP server in the Enterprise Campus Distribution layer with the DNS server in the
Internet Connectivity module.

Explanation

Question 25 of 199

1

Your company's Cisco routers are operating with EIGRP. You need to join networks with an
acquisition's heterogeneous routers at 3 sites, operating with EIGRP and OSPF. Which describes
the best practice for routing protocol deployment?

Select one of the following:

Apply OSPF throughout both networks
Apply one-way redistribution exclusively at each location
Apply two-way redistribution exclusively at each location
Apply two-way redistribution at each location with a route filter at only one location
Apply two-way redistribution at each location with a route filter at each location
Apply EIGRP with the same autonomous system throughout both networks

Explanation

Question 26 of 199

1

Which two routing protocols converge most quickly? (Choose two.)

Select one or more of the following:

RIPv1
RIPv2
BGP
OSPF
EIGRP

Explanation

Question 27 of 199

1

Which of these is the equation used to derive a 64 Kbps bit rate?

Select one of the following:

2 x 8 kHz x 4-bit code words
8 kHz x 8-bit code words
2 x 4-bit code words x 8 kHz
2 x 4 kHz x 8-bit code words

Explanation

Question 28 of 199

1

Which one of these statements is an example of how trust and identity management solutions
should be deployed in the enterprise campus network?

Select one of the following:

Authentication validation should be deployed as close to the data center as possible.
Use the principle of top-down privilege, which means that each subject should have the
privileges that are necessary to perform their defined tasks, as well as all the tasks for those roles
below them.
Mixed ACL rules, using combinations of specific sources and destinations, should be applied as
close to the source as possible.
For ease of management, practice defense in isolation - security mechanisms should be in
place one time, in one place.

Explanation

Question 29 of 199

1

With deterministic Wireless LAN Controller redundancy design, the different options available to
the designer have their own strengths. Which one of these statements is an example of such a
strength?

Select one of the following:

Dynamic load balancing, or salt-and-pepper access point design, avoids the potential impact of
oversubscription on aggregate network performance.
N+N redundancy configuration allows logically grouping access points on controllers to
minimize intercontroller roaming events.
N+N+1 redundancy configuration has the least impact to system management because all of
the controllers are colocated in an NOC or data center.
N+1 redundancy configuration uses Layer 3 intercontroller roaming, maintaining traffic on the
same subnet for more efficiency.

Explanation

Question 30 of 199

1

When designing the threat detection and mitigation portion for the enterprise data center network,
which of the following would be the most appropriate solution to consider?

Select one of the following:

802.1X
ACLs in the core layer
Cisco Security MARS
Cisco Firewall Services Module

Explanation

Question 31 of 199

1

You have a campus network that consists of only Cisco devices. You have been tasked to
discover the device platforms, the IOS versions, and an IP address of each device to map the
network. Which proprietary protocol will assist you with this task?

Select one of the following:

SNMP
TCP
CDP
ICMP
LLDP

Explanation

Question 32 of 199

1

Which three technologies are recommended to be used for WAN connectivity in today's Enterprise
Edge designs? (Choose three.)

Select one or more of the following:

DWDM
Metro Ethernet
Frame Relay
MPLS VPN
ISDN
DSL
Wireless

Explanation

Question 33 of 199

1

WAN backup over the Internet is often used to provide primary connection redundancy. Which is
the most important consideration when passing corporate traffic over the public Internet?

Select one of the following:

security
static versus dynamic routing
bandwidth
QoS
latency

Explanation

Question 34 of 199

1

To provide Layer 2 connectivity between the primary and remote data centers, given that the two
data centers are using Layer 3 routed DCIs, which NX-OS technology can be used to facilitate this
requirement?

Select one of the following:

VRF
OTV
MPLS
SPT
VPC

Explanation

Question 35 of 199

1

Which WLC interface is dedicated for WLAN client data?

Select one of the following:

virtual interface
dynamic interface
management interface
AP manager interface
service port interface

Explanation

Question 36 of 199

1

According to Cisco, which four improvements are the main benefits of the PPDIOO lifecycle
approach to network design? (Choose four.)

Select one or more of the following:

faster ROI
improved business agility
increased network availability
faster access to applications and services
lower total cost of network ownership
better implementation team engagement

Explanation

Question 37 of 199

1

Drag

Drag an answer into the correct orange point.

Email and HTTP

IP telephony and video

Budget

Security

Application compatibility

Explanation

Question 38 of 199

1

During which phase of the PPDIOO model would you conduct interviews with supporting staff to
develop and propose a viable solution?

Select one of the following:

Prepare
Plan
Design
Implement
Operate
Optimize

Explanation

Question 39 of 199

1

Which three are considered as technical constraints when identifying network requirements?
(Choose three.)

Select one or more of the following:

support for legacy applications
bandwidth support for new applications
limited budget allocation
policy limitations
limited support staff to complete assessment
support for existing legacy equipment
limited timeframe to implement

Explanation

Question 40 of 199

1

Drag

Drag an answer into the correct orange point.

Define how information is exchanged.....

provides complete network visibility....

runs iver the data link layer using a...

processes large ACLs efficiently for ...

Explanation

Question 41 of 199

1

Drag

Drag an answer into the correct orange point.

Prepare

Plan

Desing

Implement

Operate

Optimize

Explanation

Question 42 of 199

1

Characterizing an existing network requires gathering as much information about the network as
possible. Which of these choices describes the preferred order for the information-gathering
process?

Select one of the following:

site and network audits, traffic analysis, existing documentation and organizational input
existing documentation and organizational input, site and network audits, traffic analysis
traffic analysis, existing documentation and organizational input, site and network audits
site and network audits, existing documentation and organizational input, traffic analysis

Explanation

Question 43 of 199

1

QUESTION NO: 43
Which three terms describe the primary functions of the distribution layer of the campus network
design hierarchy? (Choose three.)

Select one or more of the following:

provides end-user connectivity
provides high speed transport
provides QoS services
enforces security policies
provides WAN connections
connects access devices to the core backbone

Explanation

Question 44 of 199

1

QUESTION NO: 44
Refer to the exhibit.

Which statement accurately represents the characteristics of the core layer in this design?

Select one of the following:

QoS should only be performed only in the core.
Load balancing should never be implemented or used.
Access lists should be used in the core to perform packet manipulation.
Partial mesh should be used as long as it is connected to each device by multiple paths.
Policy-based traffic control should be implemented to enable prioritization and ensure the best
performance for all time-critical applications.

Explanation

Question 45 of 199

1

QUESTION NO: 45
Which two of the following are benefits of using a modular approach to network design? (Choose
two.)

Select one or more of the following:

improves flexibility
facilitates implementation
lowers implementation costs
improves customer participation in the design process

Explanation

Question 46 of 199

1

QUESTION NO: 46
Which three modular components are part of the Cisco Enterprise Edge Architecture? (Choose
three.)

Select one or more of the following:

e-commerce module
Internet connectivity module
server farm module
remote access and VPN module
PSTN services module
enterprise branch module
building distribution module

Explanation

Question 47 of 199

1

QUESTION NO: 47
Which of the following is a component within the Cisco Enterprise Campus module?

Select one of the following:

Teleworker
E-Commerce
Internet Connectivity
Building Distribution
WAN/MAN Site-to-Site VPN

Explanation

Question 48 of 199

1

QUESTION NO: 48
What are the three primary functions of the distribution layer of the campus network design
hierarchy? (Choose three.)

Select one or more of the following:

provide end-user connectivity
provide high speed transport
provide QoS services
enforce security policies
provide WAN connections
connect access devices to the core backbone

Explanation

Question 49 of 199

1

QUESTION NO: 49 DRAG DROP

Drag an answer into the correct orange point.

The most feature-rich part of the campus

Provides security. QoS, and IP Multicast

Routing boundary (Dynamic, sumarization

Enforce Policy within the network

High leve of availability, scalability..

Provides a limited set of services

Explanation

Question 50 of 199

1

QUESTION NO: 50 DRAG DROP

Drag an answer into the correct orange point.

enables intelligent route and switch....

aggregates connectivity to voice, video.

supports application traffic througth th

provides internal users with external HT

terminates traffic that us forwarded by.

enables services-oriented architectures

Explanation

Question 51 of 199

1

QUESTION NO: 51
Where in the Cisco Enterprise Architecture model does network management reside?

Select one of the following:

Enterprise data center module
Enterprise campus module
Enterprise edge module
Service Provider edge module
Service Provider data center module

Explanation

Question 52 of 199

1

QUESTION NO: 52 DRAG DROP

Drag an answer into the correct orange point.

Protect network services including DHCP,

Protect against inadvertent loops

Protect the endpoints using network-base

Protect the infrastructure using NFP bes

Does not perform security functions to m

Filter and rate-limit control plane traf

Explanation

Question 53 of 199

1

QUESTION NO: 53
Which three solutions are part of the Borderless Network Services? (Choose three.)

Select one or more of the following:

Wireless
Routing
TrustSec
MediaNet
Switching
EnergyWise
Next-Gen WAN

Explanation

Question 54 of 199

1

QUESTION NO: 54
Refer to the exhibit.

Which two statements correctly identify the layers of the Enterprise Campus module? (Choose
two.)

Select one or more of the following:

A is the Data Center Module and C is the Campus Core layer.
A is the Data Center Module and D is the Building Access layer.
B is the Campus Core layer and C is the Building Distribution layer.
B is the Building Distribution layer and C is the Campus Core layer.
A is the Internet Connectivity layer and B is the Campus Core layer.
B is the Building Distribution layer and D is the Building Access layer.

Explanation

Question 55 of 199

1

QUESTION NO: 55
The evolution of the Data Center is best represented by the 3.0 architecture component of
virtualization. Which of the following is not an example of the virtualization taking place in the Data
Center?

Select one of the following:

Virtualized media access utilizing Fiber Channel over Ethernet
VLANs and virtual storage area networks (VSANs) provide for virtualized LAN and SAN
connectivity, separating physical networks and equipment into virtual entities
Virtual Machines that run an application within the client operating system, which is further
virtualized and running on common hardware
Storage devices virtualized into storage pools, and network devices are virtualized using device
contexts

Explanation

Question 56 of 199

1

QUESTION NO: 56
When there is a need for immunity to EMI for connecting locations that are greater than 100
meters apart, which two solutions can be utilized? (Choose two.)

Select one or more of the following:

multimode fiber
Fiber Channel
HVDC transmission lines
single-mode fiber
serial RS-232
Gigabit Ethernet 1000BASE-CX

Explanation

Question 57 of 199

1

QUESTION NO: 57
Which layer of the OSI model does Cisco recommend to place the enterprise network core layer,
when designing a network based on its switched hierarchical design?

Select one of the following:

Layer 1
Layer 2
Layer 3
Layer 4

Explanation

Question 58 of 199

1

QUESTION NO: 58
OSPF will be used as the IGP within a campus network. Which two things should you consider
before deployment? (Choose two.)

Select one or more of the following:

All areas need to connect back to area 0.
The OSPF process number on each router should match.
NSSA areas should be used when an area cannot connect directly to area 0.
Stub areas should be connected together using virtual links.
ECMP may cause undesired results depending on the environment.

Explanation

Question 59 of 199

1

QUESTION NO: 59
Which Cisco technology using Nexus NX-OS infrastructure allows the network architect to create
up to four separate control and data plane instances of the Nexus chassis?

Select one of the following:

virtual port-channel
virtual routing and forwarding
virtual switching system
virtual device context

Explanation

Question 60 of 199

1

QUESTION NO: 60
Which three options are valid Cisco STP tools used to ensure best-practice access layer design
for the enterprise campus? (Choose three.)

Select one or more of the following:

Port fast
UDLD
Root Guard
BPDU Guard
Flex Links
SPAN
Ether Channel

Explanation

Question 61 of 199

1

QUESTION NO: 61
Spanning Layer 2 across geographically separate data centers is a key consideration for current
data center designs. Which is the name of the NX-OS technology that facilitates MAC in IP
transport for Layer 2 VLANs across any IP network?

Select one of the following:

Overlay Transport Virtualization
Virtual Private LAN Services
Generic Routing Encapsulation
QinQ tunneling

Explanation

Question 62 of 199

1

QUESTION NO: 62
Which two statements about designing the Data Center Access layer are correct? (Choose two.)

Select one or more of the following:

Multiport NIC servers should each have their own IP address.
Layer 3 connectivity should never be used in the access layer.
Layer 2 connectivity is primarily implemented in the access layer.
Multiport NIC servers should never be used in the access layer.
Layer 2 clustering implementation requires servers to be Layer 2 adjacent.

Explanation

Question 63 of 199

1

QUESTION NO: 63
What is the primary consideration when choosing a routed network design over a traditional
campus network design?

Select one of the following:

Layer 3 service support at the network edge
the routing protocol choice: open (OSPF) or proprietary (EIGRP)
the routing abilities of the host devices
the need to control the broadcast domains within the campus core

Explanation

Question 64 of 199

1

QUESTION NO: 64
When selecting which hardware switches to use throughout an enterprise campus switched
network, which consideration is not relevant?

Select one of the following:

whether data link layer switching based upon the MAC address is required
the number of shared media segments
which infrastructure service capabilities are required
whether to support Layer 3 services at the network edge

Explanation

Question 65 of 199

1

QUESTION NO: 65
Which two of these practices are considered to be best practices when designing the access layer
for the enterprise campus? (Choose two.)

Select one of the following:

Implement all of the services (QoS, security, STP, and so on) in the access layer, offloading the
work from the distribution and core layers.
Always use a Spanning Tree Protocol; preferred is Rapid PVST+.
Use automatic VLAN pruning to prune unused VLANs from trunked interfaces to avoid
broadcast propagation.
Avoid wasted processing by disabling STP where loops are not possible.
Use VTP transparent mode to decrease the potential for operational error.

Explanation

Question 66 of 199

1

QUESTION NO: 66
The enterprise campus core layer has requirements that are unique from the distribution and
access layers. Which of the following is true about the core layer?

Select one of the following:

The core layer provides convergence using Layer 2 and Layer 3 services and features.
The core layer provides high availability to support the distribution layer connections to the
enterprise edge.
The campus core layer is optional.
The core layer requires high performance to manage the traffic policing across the backbone.

Explanation

Question 67 of 199

1

QUESTION NO: 67
Which of these statements is true concerning the data center access layer design?

Select one of the following:

The access layer in the data center is typically built at Layer 3, which allows for better sharing
of services across multiple servers.
With Layer 2 access, the default gateway for the servers can be configured at the access or
aggregation layer.
A dual-homing NIC requires a VLAN or trunk between the two access switches to support the
dual IP addresses on the two server links to two separate switches.
The access layer is normally not required, as dual homing is standard from the servers to the aggregation layer.

Explanation

Question 68 of 199

1

QUESTION NO: 68
Which one of these statements is true concerning the data center distribution (aggregation) layer
design?

Select one of the following:

With Layer 3 at the aggregation layer, the physical loops in the topology must still be managed
by STP.
The boundary between Layer 2 and Layer 3 must reside in the multilayer switches, independent
of any other devices such as firewalls or content switching devices.
A mix of both Layer 2 and Layer 3 access is sometimes the most optimal.
In a small data center, the aggregation layer can connect directly to the campus core,
exchanging IP routes and MAC address tables.

Explanation

Question 69 of 199

1

QUESTION NO: 69 DRAG DROP

Drag an answer into the correct orange point.

vPC

VLAN

VRF

Asa Firewall context

IPS

VDC

Explanation

Question 70 of 199

1

QUESTION NO: 70
Refer to the exhibit.

Which statement is true concerning enterprise edge distribution switches?

Select one of the following:

The speed of switching is the most critical feature.
Security requirements are offloaded to the other modules for performance reasons.
Edge distribution switches are only required when using a collapsed core backbone.
Enterprise edge distribution switches are similar to the building distribution layer.

Explanation

Question 71 of 199

1

An enterprise campus module is typically made up of four sub modules, as described by the Cisco
Enterprise Architecture Model. Which two sub modules are part of this module?

Select one or more of the following:

DMZ
enterprise branch
building distribution
server farm/data center
MAN

Explanation

Question 72 of 199

1

QUESTION NO: 72
Which is a factor in enterprise campus design decisions?

Select one of the following:

network application characteristics
routing protocol characteristics
switching latency characteristics
packet filtering characteristics

Explanation

Question 73 of 199

1

QUESTION NO: 73
Which network virtualization technology involves creating virtual routers with its own individual
routing tables on a physical router?

Select one of the following:

VSS
vPC
VRF
VLAN

Explanation

Question 74 of 199

1

QUESTION NO: 74
Which protocol is the recommended first-hop redundancy protocol for an existing infrastructure
that contains multiple vendors and platforms?

Select one of the following:

HSRP
VRRP
IGRP
OSPF

Explanation

Question 75 of 199

1

QUESTION NO: 75
Which IGP provides the fastest convergence by default?

Select one of the following:

EIGRP
OSPF
IS-IS
RSTP
BGP

Explanation

Question 76 of 199

1

QUESTION NO: 76
Which three are valid Layer 2 access designs? (Choose three.)

Select one or more of the following:

Looped Triangle
Looped Square
Looped U
Loop-Free Triangle
Loop-Free Square
Loop-Free U

Explanation

Question 77 of 199

1

QUESTION NO: 77
Which Gigabit Ethernet media type provides the longest reach without a repeater?

Select one of the following:

1000Base-CX
1000Base-LX
1000Base-SX
1000Base-T

Explanation

Question 78 of 199

1

QUESTION NO: 78 DRAG DROP

Drag an answer into the correct orange point.

Support Layer 2 VLANs spanning multiple

FHRP for convergence, no VLANs span betw

Convergence (FHRP) is not an issue

Explanation

Question 79 of 199

1

QUESTION NO: 79
Which three are associated with the distribution layer within the campus design? (Choose three.)

Select one or more of the following:

access layer aggregation
route summarization
network trust boundary
next-hop redundancy
layer 2 switching
port security
broadcast suppression

Explanation

Question 80 of 199

1

QUESTION NO: 80
High availability is a key design consideration in the enterprise campus network. In a fully
redundant topology, which is likely to provide faster IGP convergence during a failure?

Select one of the following:

redundant supervisors
redundant supervisors with Cisco Nonstop Forwarding (NSF) and Stateful Switchover (SSO)
single supervisors with tuned IGP timers
single supervisors

Explanation

Question 81 of 199

1

QUESTION NO: 81
Which two enterprise campus layers are combined in a medium-sized LAN? (Choose two.)

Select one or more of the following:

core
distribution
access
backbone
aggregation

Explanation

Question 82 of 199

1

QUESTION NO: 82
What is a characteristic of campus core designs?

Select one of the following:

fast transport
security
summarization
redistribution

Explanation

Question 83 of 199

1

QUESTION NO: 83
In the enterprise data center, which are the three main components? (Choose three.)

Select one or more of the following:

Network Infrastructure
Interactive services
Data Center Management
Internet services
WAN services
VPN and remote access

Explanation

Question 84 of 199

1

QUESTION NO: 84
Which two common cable management strategies are used in high-density server deployments in
the data center? (Choose two.)

Select one or more of the following:

top-of-rack
middle-of-rack
bottom-of-rack
beginning-of-row
middle-of-row
end-of-row

Explanation

Question 85 of 199

1

QUESTION NO: 85
Which servers that reside in the data center require direct links to all other enterprise modules?

Select one of the following:

network management servers
DHCP servers
Active Directory servers
IP SLA servers
web servers

Explanation

Question 86 of 199

1

QUESTION NO: 86 DRAG DROP

Drag an answer into the correct orange point.

Cisco VN-Link techologies, including the

VSAN, virtual devices contents and unifi

Cisco Unifien Computing System

VLANs and VSANs

Explanation

Question 87 of 199

1

QUESTION NO: 87
When designing using the Cisco Enterprise Architecture, in which Enterprise Campus layer does the Remote Access and VPN module establish its connection?

Select one of the following:

Building Access
Campus Core
Enterprise Branch
Enterprise Data Center

Explanation

Question 88 of 199

1

QUESTION NO: 88 DRAG DROP

Drag an answer into the correct orange point.

TDM

SONET

Frame Relay

MPLS

Explanation

Question 89 of 199

1

QUESTION NO: 89
Which three describe challenges that are faced when deploying an environment for teleworkers?
(Choose three.)

Select one or more of the following:

supporting a mix of technically knowledgeable and nontechnical users
simplifying router installation and configuration
verifying available power at employee's house for necessary equipment
avoiding situations where employees might use nonstandard hardware or configurations
reducing daily commuting time to main office location
providing access to FTP servers located in main office location
implementing leased line connectivity between main office and employee's home location

Explanation

Question 90 of 199

1

QUESTION NO: 90
You need to connect to a remote branch office via an Internet connection. The remote office does
not use Cisco equipment. This connection must be secure and must support OSPF. Which of the
following can be used to transport data to the branch office?

Select one of the following:

GRE over IPsec
IPsec
GRE
IPsec VTI

Explanation

Question 91 of 199

1

QUESTION NO: 91
Which two are characteristics of a Lightweight Access Point? (Choose two.)

Select one or more of the following:

managed via a central wireless LAN controller
code upgrade performed via a TFTP server
CAPWAP tunnels
managed directly via CLI or web interface
facilitates the creation of its own WLANs and port mappings

Explanation

Question 92 of 199

1

QUESTION NO: 92
Which one of these statements describes why, from a design perspective, a managed VPN
approach for enterprise teleworkers is most effective?

Select one of the following:

A managed VPN solution uses a cost-effective, on-demand VPN tunnel back to the enterprise.
This solution supports all teleworkers who do not require voice or video.
This architecture provides centralized management where the enterprise can apply security
policies and push configurations.
It provides complete flexibility for remote access through a wireless hotspot or a guest network
at a hotel, in addition to a home office.

Explanation

Question 93 of 199

1

QUESTION NO: 93
What are three key areas that need to be considered when designing a remote data center? (Choose three.)

Select one or more of the following:

power diversity
active directory services
Cisco IOS versions
data storage
applications
user access
packet routing

Explanation

Question 94 of 199

1

QUESTION NO: 94
If a teleworker is required to access the branch office via a secure IPSEC VPN connection, which
technology is recommended to provide the underlying transport?

Select one of the following:

ISDN
Metro Ethernet
Frame Relay
ADSL
ATM

Explanation

Question 95 of 199

1

QUESTION NO: 95
Which model of ISR is utilized for the teleworker design profile?

Select one of the following:

Cisco 1900 Series
Cisco 1800 Series
Cisco 800 Series
Cisco 500 Series

Explanation

Question 96 of 199

1

QUESTION NO: 96
When designing a WAN backup for voice and video applications, what three types of connections
should be used? (Choose three.)

Select one or more of the following:

Private WAN
internet
ISDN
MPLS
dial-up
ATM
DSL

Explanation

Question 97 of 199

1

QUESTION NO: 97
Which three options represents the components of the Teleworker Solution? (Choose three.)

Select one or more of the following:

Cisco Unified IP Phone
Cisco 880 Series Router
Aironet Office Extend Access Point
Catalyst 3560 Series Switch
Cisco 2900 Series Router
MPLS Layer 3 VPN
Leased lines

Explanation

Question 98 of 199

1

QUESTION NO: 98
Which three service categories are supported by an ISR? (Choose three.)

Select one or more of the following:

voice
security
data
Internet
storage
satellite

Explanation

Question 99 of 199

1

QUESTION NO: 99
When designing for a remote worker, which two are typical requirements? (Choose two.)

Select one or more of the following:

best-effort interactive and low-volume traffic patterns
connections to the enterprise edge using Layer 2 WAN technologies
always-on connection with SLA from ISP
voice and IPsec VPN support
high-end security devices with stateful firewall filtering
dual or multihoming to ISPs

Explanation

Question 100 of 199

1

QUESTION NO: 100
What is the maximum number of groups that is supported by GLBP?

Select one of the following:

64
256
512
1024

Explanation

Question 101 of 199

1

QUESTION NO: 101 DRAG DROP

Drag an answer into the correct orange point.

window size

data compression

queuing

traffic policing

Explanation

Question 102 of 199

1

QUESTION NO: 102
Which two routing protocols usually converge most quickly? (Choose two.)

Select one or more of the following:

RIPv1
RIPv2
BGP
OSPF
EIGRP

Explanation

Question 103 of 199

1

QUESTION NO: 103
Which two routing protocols operate over NBMA point-to-multipoint networks without the use of
point-to-point sub interfaces? (Choose two.)

Select one or more of the following:

RIPv1
RIPv2
IS-IS
EIGRP
OSPF

Explanation

Question 104 of 199

1

QUESTION NO: 104
Refer to the exhibit.

Which three modules would typically utilize public IPv4 addressing? (Choose three.)

Select one or more of the following:

Access
Distribution
Core
Data Center
E-Commerce
Internet Connectivity
Remote Access/VPN
WAN/MAN
Branch
Branch Data Center

Explanation

Question 105 of 199

1

QUESTION NO: 105
With respect to IPv6 addressing, from a design perspective, which of these statements is it
important to keep in mind?

Select one of the following:

IPv6 addressing provides convenience of anycast addressing without any configuration
requirements.
IPv6 does not use multicast addressing.
An IPv6 router will not forward packets from one link to other links if the packet has either a linklocal
source or a link-local destination address.
Dynamic address assignment requires DHCPv6.

Explanation

Question 106 of 199

1

QUESTION NO: 106
Which consideration is the most important for the network designer when considering IP routing?

Select one of the following:

convergence
scalability
on-demand routing
redistribution

Explanation

Question 107 of 199

1

QUESTION NO: 107
Your supervisor has asked you to deploy a routing protocol within the lab environment that will
allow for unequal cost multipath routing. Which should you choose?

Select one of the following:

EIGRP
OSPF
IS-IS
RIP

Explanation

Question 108 of 199

1

QUESTION NO: 108
Which two methods are used to reduce the mesh links required between iBGP peers in the same
AS? (Choose two.)

Select one or more of the following:

community
router reflectors
local preference
confederations
atomic aggregate
MED

Explanation

Question 109 of 199

1

QUESTION NO: 109
A company wants to use private IP addresses for all its internal hosts. Which technology can the
company use to provide access to the Internet using a single public IP address?

Select one of the following:

static NAT
source routing
ACL
PAT

Explanation

Question 110 of 199

1

QUESTION NO: 110
At which layer of the network is route summarization recommended?

Select one of the following:

data link layer
core layer
distribution layer
access layer

Explanation

Question 111 of 199

1

QUESTION NO: 111
Which two link state routing protocols support IPv6 routing? (Choose two.)

Select one or more of the following:

BGP4+
OSPF
RIPng
EIGRP
IS-IS

Explanation

Question 112 of 199

1

QUESTION NO: 112
Which is the North American RIR for IPv4 addresses?

Select one of the following:

RIPE
ARIN
IEEE
APNIC

Explanation

Question 113 of 199

1

QUESTION NO: 113
What is the most compact representation of the following IPv6 address?
2001:db8:0000:0000:cafe:0000:0000:1234

Select one of the following:

2001:db8::cafe::1234
2001:db8::cafe:0000:0000:1234
2001:db8:0:0:cafe::1234
2001:db8::cafe:0:1234

Explanation

Question 114 of 199

1

QUESTION NO: 114
Which type of area should you use in an enterprise OSPF deployment if you want to prevent
propagation of type 5 LSAs but still allow the redistribution of external routes?

Select one of the following:

stub
totally stubby
backbone
NSSA
virtual link

Explanation

Question 115 of 199

1

QUESTION NO: 115
Which is usually used to connect to an upstream ISP?

Select one of the following:

EIGRP
OSPF
BGP
IS-IS
RIPv2

Explanation

Question 116 of 199

1

QUESTION NO: 116
You are designing a network that requires a routing protocol that will use minimal network
bandwidth. Which would satisfy this requirement?

Select one of the following:

RIPv2
RIPng
OSPF
ARP
EGP

Explanation

Question 117 of 199

1

QUESTION NO: 117
Which two statements best describe an OSPF deployment? (Choose two.)

Select one or more of the following:

ABR provides automatic classful network boundary summarization.
ABR requires manual configuration for classful network summarization.
External routes are propagated into the autonomous system from stub areas via ASBR.
External routes are propagated into the autonomous system from regular areas or NSSA via
ASBR.
External routes are propagated into the autonomous system from regular areas or NSSA via
ABR.

Explanation

Question 118 of 199

1

QUESTION NO: 118
Which three items pertain to EIGRP? (Choose three.)

Select one or more of the following:

Can use multiple unequal paths.
Routes are redistributed as type 2 by default.
ASN and K values must match to form neighbors.
Uses multicast address 224.0.0.9 for updates.
Exchanges full routing table every 30 seconds.
Summary routes have AD of 90.
External routes have AD of 170.

Explanation

Question 119 of 199

1

QUESTION NO: 119
A hierarchical design of the EIGRP domain facilitates which two of the following? (Choose two.)

Select one or more of the following:

route summarization
faster convergence
unequal cost load balancing
redistribution
virtual links

Explanation

Question 120 of 199

1

QUESTION NO: 120
Which three protocols support VLSM? (Choose three.)

Select one or more of the following:

RIPv2
RIPv1
EIGRP
OSPF
IGRP

Explanation

Question 121 of 199

1

QUESTION NO: 121
Which statement should the designer keep in mind when considering the advanced routing
features?

Select one or more of the following:

One-way route redistribution avoids the requirement for static or default routes.
Redistribution, summarization, and filtering are most often applied between the campus core
and enterprise edge.
Filtering only occurs on the routing domain boundary using redistribution.
Summarize routes at the core toward the distribution layer.
The hierarchical flexibility of IPv6 addressing avoids the requirement for routing traffic reduction
using aggregation.

Explanation

Question 122 of 199

1

QUESTION NO: 122
When designing an EIGRP network, which two things should you take into consideration?
(Choose two.)

Select one or more of the following:

ASN and K values must match.
The neighbor command can be used to enable unicast communication.
The neighbor diameter cannot exceed a 15-hops limit.
NSSA areas can be used to redistribute external routes.
Neighbor relationship can be established with non-Cisco routers.

Explanation

Question 123 of 199

1

QUESTION NO: 123
Which statement describes a unique advantage of EIGRP?

Select one of the following:

It enables unequal-cost load balancing.
It enables equal-cost load balancing.
It enables source-based load balancing.
It enables port-based load balancing.

Explanation

Question 124 of 199

1

QUESTION NO: 124
ACME corporation is implementing dynamic routing on the LAN at its corporate headquarters. The
interior gateway protocol that they select must support these requirements: multivendor
environment, efficient subnetting, high scalability, and fast convergence. Which interior gateway
protocol should they implement?

Select one of the following:

EIGRP
OSPF
RIPng
BGP

Explanation

Question 125 of 199

1

QUESTION NO: 125
Which routing protocol classification should you use when full topology information is needed?

Select one of the following:

link-state
distance vector
stateful
path vector

Explanation

Question 126 of 199

1

QUESTION NO: 126
When you are designing a large IPv6 multivendor network, which IGP does Cisco recommend that
you use?

Select one of the following:

OSPFv3
EIGRP for IPv6
BGP
RIPng

Explanation

Question 127 of 199

1

QUESTION NO: 127
When designing the infrastructure protection portion for the enterprise edge, which solution would
be the most appropriate solution to consider?

Select one of the following:

802.1X
ACLs in the core layer
Cisco Security MARS
AAA

Explanation

Question 128 of 199

1

QUESTION NO: 128
Which two design approaches provide management of enterprise network devices? (Choose two.)

Select one or more of the following:

in-band
out-of-line
out-of-band
in-line

Explanation

Question 129 of 199

1

QUESTION NO: 129
You are asked to design a new branch office that will need to support 25 users. These users will
be using an ISP connection and will need to connect to the main office for network services. Which
two Cisco devices are the most appropriate to fulfill all of these requirements? (Choose two.)

Select one or more of the following:

Cisco IPS
Cisco ISR G2
Cisco ASA
Cisco 2960
Cisco CRS-1
Cisco ACS

Explanation

Question 130 of 199

1

QUESTION NO: 130
What are the three modes of unicast reverse path forwarding? (Choose three.)

Select one or more of the following:

strict
loose
VRF
global
PIM
local

Explanation

Question 131 of 199

1

QUESTION NO: 131
Which network access control technology is recommended to use with Layer 2 access layer
switches?

Select one of the following:

802.1q
802.1x
802.3af
802.3q
802.11n

Explanation

Question 132 of 199

1

QUESTION NO: 132
Refer to the list of requirements. Which IP telephony design model should you implement to fulfill
these requirements? - must be a single, large location with many remote sites - must have
multisite WAN connectivity - requires SRST for call processing redundancy

Select one of the following:

centralized
distributed
clustered
decentralized

Explanation

Question 133 of 199

1

Which is the equation used to derive a 64 Kbps bit rate?

Select one of the following:

2 x 8 kHz x 4-bit code words
8 kHz x 8-bit code words
2 x 4-bit code words x 8 kHz
2 x 4 kHz x 8-bit code words

Explanation

Question 134 of 199

1

QUESTION NO: 134
Which three statements are true regarding the virtual interface on a Cisco Wireless LAN
Controller? (Choose three.)

Select one or more of the following:

supports mobility management
serves as a DHCP relay
used for all controller to AP communication
supports embedded Layer 3 security
default for out-of-band management
default for in-band management
provides connectivity to AAA servers

Explanation

Question 135 of 199

1

QUESTION NO: 135
A campus network needs end-to-end QoS tools to manage traffic and ensure voice quality. Which
three types of QoS tools are needed? (Choose three.)

Select one or more of the following:

interface queuing and scheduling
congestion management
compression and fragmentation
bandwidth provisioning
traffic classification
buffer management

Explanation

Question 136 of 199

1

QUESTION NO: 136
Which technology enables WLCs to peer with each other to enable roaming support?

Select one of the following:

WAP profiles
roaming profiles
mobility groups
peer groups

Explanation

Question 137 of 199

1

QUESTION NO: 137
Which IP telephony component supports VoIP, PoE, and QoS?

Select one of the following:

client endpoints
voice-enabled infrastructure
Cisco Unified Communications Manager
Cisco Unified Contact Center

Explanation

Question 138 of 199

1

QUESTION NO: 138
Your supervisor wants you to recommend a management protocol that will allow you to track
overall bandwidth utilization, utilization by traffic type, and utilization by source and destination.
Which is ideally suited for this function?

Select one of the following:

MRTG
NetFlow
RRD
SNMP

Explanation

Question 139 of 199

1

QUESTION NO: 139
Which factor would be most influential in choosing multimode fiber optic connections over UTP?

Select one of the following:

signal attenuation
required bandwidth
required distance
electromagnetic interference
cost

Explanation

Question 140 of 199

1

QUESTION NO: 140
Which WAN technology is a cost-effective method to deliver 100Mb of bandwidth to multiple
branch offices?

Select one of the following:

DSL
DWDM
ISDN
Metro Ethernet

Explanation

Question 141 of 199

1

QUESTION NO: 141
Which subnet address and mask would you use for all Class D multicast addresses to be matched
within an access list?

Select one of the following:

224.0.0.0/20
224.0.0.0/4
239.0.0.0/24
239.0.0.0/8
225.0.0.0/8

Explanation

Question 142 of 199

1

QUESTION NO: 142
A company is implementing an Identity Management solution with these characteristics:
1) existing AAA Server
2) Cisco Catalyst switches
3) minimal added investments
Which Cisco Trust and Identity Management solution would you recommend?

Select one of the following:

NAC Appliance
Cisco IBNS
CSM
Cisco Security MARS

Explanation

Question 143 of 199

1

QUESTION NO: 143
When considering the three VoIP design models - single site, centralized multisite, and distributed
multisite - which question below would help to eliminate one of the options?

Select one of the following:

Will the switches be required to provide inline power?
Will users need to make offsite calls, beyond the enterprise?
Will users require applications such as voice mail and interactive voice response?
Are there users whose only enterprise access is via a QoS-enabled WAN?

Explanation

Question 144 of 199

1

QUESTION NO: 144
Which two devices would you place in your DMZ to ensure enterprise edge security? (Choose
two.)

Select one or more of the following:

IPS
NAC
ASA
ACS
WCS

Explanation

Question 145 of 199

1

QUESTION NO: 145
Which three are security services offered through Cisco Router Security? (Choose three.)

Select one or more of the following:

Trust and Identity
Integrated Threat Control
Unified Wireless Network Security Solution
Secure Connectivity
Voice-Messaging Security
Endpoint Security
Virtual Security Gateway

Explanation

Question 146 of 199

1

QUESTION NO: 146
Which voice codec should you use in order to provide toll quality calls?

Select one of the following:

G.711
G.718
G.722
G.729

Explanation

Question 147 of 199

1

QUESTION NO: 147
Which three are features of LWAPP? (Choose three.)

Select one or more of the following:

firmware synchronization
local management of APs
configuration changes manually synced
encryption of control channel
configuration data only on the WLC
wireless control free operation
replaces 802.1x for authentication in wireless connections

Explanation

Question 148 of 199

1

QUESTION NO: 148
Which Cisco device has the sole function at looking at threat detection and mitigation at the
Enterprise edge?

Select one of the following:

Cisco IOS router
Cisco ASA
Cisco Catalyst FWSM
Cisco IPS

Explanation

Question 149 of 199

1

QUESTION NO: 149
Which three of these are layers in the Cisco SONA Architecture? (Choose three.)

Select one or more of the following:

Applications
Physical Infrastructure
Presentation
Integrated Transport
Core Common Services
Networked Infrastructure

Explanation

Question 150 of 199

1

QUESTION NO: 150
What business trend allows employees to use personal devices to access enterprise data and
systems?

Select one of the following:

ISE
BYOD
SAN
IOE

Explanation

Question 151 of 199

1

QUESTION NO: 151
What three customer supported details identifies network requirements based on the PPDIOO
design model? (Choose three.)

Select one or more of the following:

goals
budget
user needs
locations
policies
tasks

Explanation

Question 152 of 199

1

QUESTION NO: 152
An engineer receives a resource utilization alert on a router. What command should be used to
investigate the issue?

Select one of the following:

show processes cpu
show memory
show running-config
show version

Explanation

Question 153 of 199

1

QUESTION NO: 153
What part of the network does a top-down network design focus on for solution development?

Select one of the following:

presentation
hardware
session
application
data link
transport

Explanation

Question 154 of 199

1

QUESTION NO: 154
An engineer has configured a router to send level 7 messages to a syslog server. What severity
level are these messages?

Select one of the following:

error
warning
debug
informational
notice

Explanation

Question 155 of 199

1

QUESTION NO: 155
A network engineer must implement a design where LAN clients are to connect to various access
layer devices, while remaining on the same VLAN . What type of design would support this
requirement?

Select one of the following:

routed
switched
tunneled
virtual

Explanation

Question 156 of 199

1

QUESTION NO: 156
When evaluating network designs, what indicator demonstrates that the modular approach was
followed?

Select one of the following:

ability to scale
follows best practices
redundant connectivity
easy to deploy

Explanation

Question 157 of 199

1

QUESTION NO: 157
A network engineer is following the Cisco enterprise architecture model. To which network layer
would a branch office connect to using a private WAN?

Select one of the following:

Enterprise Campus
Enterprise Edge
SP Edge Premise
Remote Module

Explanation

Question 158 of 199

1

QUESTION NO: 158
A network engineer is following the three tiered Network Hierarchical Model. At which tier is route
summarization implemented?

Select one of the following:

core
distribution
backbone
access

Explanation

Question 159 of 199

1

QUESTION NO: 159
A network engineer is using the Cisco enterprise architecture model. In what module do network
management servers reside?

Select one of the following:

Enterprise Campus
Enterprise Edge
Remote Modules
SP Edge WAN/internet

Explanation

Question 160 of 199

1

QUESTION NO: 160
What three design requirements are key to designing a campus core? (Choose three.)

Select one or more of the following:

low latency
access control
traffic filtering
high speed
redundant links
QoS tagging

Explanation

Question 161 of 199

1

QUESTION NO: 161
What type of device can be installed to increase a broadcast domain?

Select one of the following:

router
switch
IDS
IPS

Explanation

Question 162 of 199

1

QUESTION NO: 162
To what Layer 2 technology does VRF closely compare?

Select one of the following:

VSS
VPC
VLAN
VTP

Explanation

Question 163 of 199

1

QUESTION NO: 163
What network virtualization technology can be leveraged within the data center to reduce the
number of physical devices?

Select one of the following:

VLANs
VPLS
VDC
VSS

Explanation

Question 164 of 199

1

QUESTION NO: 164
During the design of a new campus network, the customer requests the ability to route overlapping
IP addresses. What technology can be leveraged to meet this request?

Select one of the following:

VRF
VLANs
VSS
VPC

Explanation

Question 165 of 199

1

QUESTION NO: 165
A network engineer is attempting to separate routing domains using a virtualization technology.
What protocol can be configured to perform this task?

Select one of the following:

VLAN
VSAN
VRF
VPC

Explanation

Question 166 of 199

1

QUESTION NO: 166
What device virtualization technology allows for a single point of management and a centralized
routing instance?

Select one of the following:

ACE
VSS
VDC
VM

Explanation

Question 167 of 199

1

QUESTION NO: 167
What two performance considerations must be taken into account when designing a remote
worker access solution? (Choose two.)

Select one or more of the following:

simultaneous VPN connections
port density
throughput capacity
packet size
latency

Explanation

Question 168 of 199

1

QUESTION NO: 168
In which network location should an external DNS server be placed?

Select one of the following:

campus data center
enterprise branch
internet
remote access

Explanation

Question 169 of 199

1

QUESTION NO: 169
What submodule is found within the Enterprise Edge module?

Select one of the following:

enterprise WAN
remote branch
campus IPS
building distribution

Explanation

Question 170 of 199

1

QUESTION NO: 170
A company requires a managed WAN solution that supports Layer 2 adjacency across remote
offices for applications and services. What solution should be selected?

Select one of the following:

DMVPN
MPLS
VPLS
FR

Explanation

Question 171 of 199

1

QUESTION NO: 171
A circuit order has been placed for Gigabit Ethernet and is 80KM from the carrier equipment. What
type of SFP will be required?

Select one of the following:

TX
SX
ZX
LX

Explanation

Question 172 of 199

1

QUESTION NO: 172
A company has dark fiber between headquarters and its data center. It is presently configured as
a 10GbE connection. Network utilization shows high utilization on the connection. What
technology can be implemented to increase capacity without acquiring another circuit?

Select one of the following:

MPLS
DWDM
VPLS
DMVPN

Explanation

Question 173 of 199

1

QUESTION NO: 173
A secure WAN design requires dynamic routing and IP multicast. What two VPN protocols meet
these requirements? (Choose two.)

Select one or more of the following:

Standard IPsec
P2P GRE over IPsec
DMVPN
AnyConnect
PPTP
Easy VPN
SSL/TLS

Explanation

Question 174 of 199

1

QUESTION NO: 174
What branch design supports 100 to 1000 users and integrates ASA firewalls?

Select one of the following:

small
medium
large
extra large

Explanation

Question 175 of 199

1

QUESTION NO: 175
A network engineer is designing an enterprise managed VPN solution for a large number of
remote offices that do not have on-site IT support and communicate only with the home office.
What type of VPN solution should be implemented?

Select one of the following:

VPLS
GRE
IPsec
EVPN
DMVPN
SSL client

Explanation

Question 176 of 199

1

QUESTION NO: 176
A remote office has a T1 WAN link to headquarters and a T1 Internet connection. The client
requests WAN redundancy to headquarters with similar bandwidth. What two connection types
satisfy this requirement? (Choose two.)

Select one or more of the following:

Secondary T1 WAN circuit
ISDN BRI
IPSec Tunnel over the Internet
DWDM l
POTS Line T1 WAN

Explanation

Question 177 of 199

1

QUESTION NO: 177
What two features are advantages of adding a secondary WAN link at the enterprise edge?
(Choose two.)

Select one or more of the following:

provides additional bandwidth and load balancing capabilities
acts as a backup link in event the primary link fails
reduces capital and operational costs
improves security and prevents against denial of service attacks
distributes traffic proactively based on link utilization

Explanation

Question 178 of 199

1

QUESTION NO: 178
What technology can secure data over an insecure medium and provide WAN redundancy in the
event of a primary connection failure?

Select one of the following:

virtual private network
shadow PVC
dial-up ISDN
GRE Tunnel

Explanation

Question 179 of 199

1

QUESTION NO: 179
A client wants to consolidate applications that are currently housed at multiple sites to a remote
data center. What two design requirements are unique to this scenario? (Choose two.)

Select one or more of the following:

bandwidth
security
latency
storage
availability

Explanation

Question 180 of 199

1

QUESTION NO: 180
What IPv4 addressing technique allows for the division of addresses into subnets of different sizes?

Select one of the following:

VLSM
RIR
CIDR
NAT

Explanation

Question 181 of 199

1

QUESTION NO: 181
An organization is conducting an evaluation on the migration to IPv6 within the enterprise network
and has requested clarification on recommended migration strategies. What three migration
models would accomplish the organization's goal? (Choose three.)

Select one or more of the following:

Dual Stack
Service Block
Top-Down
Hybrid
Tunneled
Fork-Lift

Explanation

Question 182 of 199

1

QUESTION NO: 182
An application uses broadcast traffic to send data to IPv4 hosts. How can the application
communicate using IPv6?

Select one of the following:

Anycast
Unicast
Broadcast
Multicast

Explanation

Question 183 of 199

1

QUESTION NO: 183
What significant advantage does EIGRP have over OSPF?

Select one of the following:

easy summarization
shorter convergence times
single area operation
low processor utilization

Explanation

Question 184 of 199

1

QUESTION NO: 184
What routing protocol requires full mesh between internal peers in an enterprise network?

Select one of the following:

OSPF
EIGRP
BGP
ISIS
RIP

Explanation

Question 185 of 199

1

QUESTION NO: 185
What three considerations should be taken into account when selecting a routing protocol?
(Choose three.)

Select one or more of the following:

classful routing
scalability
default route origination
multi vendor support
link load balancing
hop count

Explanation

Question 186 of 199

1

QUESTION NO: 186
By default, how does EIGRP's metric differ from OSPF?

Select one of the following:

hops
cost
bandwidth
delay

Explanation

Question 187 of 199

1

QUESTION NO: 187
What characteristic separates link state routing protocols from a distance vector?

Select one of the following:

creates a topological view of the entire network
path calculation utilizes a more granular metric
does not scale well for large networks
constantly shares link state updates throughout the topology

Explanation

Question 188 of 199

1

QUESTION NO: 188
A company must deploy an IGP routing protocol on an Enterprise Network. Where should route
summarization be implemented?

Select one of the following:

distribution
core
access
backbone

Explanation

Question 189 of 199

1

QUESTION NO: 189
What routing configuration can prevent routing loops between IGPs?

Select one of the following:

route filters
route reflectors
auto summarization
virtual links

Explanation

Question 190 of 199

1

QUESTION NO: 190
What is the first step when creating a network security policy?

Select one of the following:

define what should be protected
investigate how likely an attack is to occur
implement measures to protect assets
hire a security firm to perform penetration tests

Explanation

Question 191 of 199

1

QUESTION NO: 191
A customer requests a filtering design based on the need to scan all internet traffic, including
remote workers. What solution meets these requirements?

Select one of the following:

Cisco Cloud Web Security
Cisco Network Admission Control
Cisco Identity Services Engine
Cisco Adaptive Security Appliance

Explanation

Question 192 of 199

1

QUESTION NO: 192
A customer wants to support a BYOD environment. What two products allow for posture
assessment? (Choose two.)

Select one or more of the following:

ACS
NAC
ASA
ISE
WAAS
IDS

Explanation

Question 193 of 199

1

QUESTION NO: 193
What two CoS values are used by voice traffic? (Choose two.)

Select one or more of the following:

COS1
COS2
COS3
COS4
COS5

Explanation

Question 194 of 199

1

QUESTION NO: 194
A client wants to deploy a video conferencing platform in a multisite WAN environment. What two
design considerations need to be evaluated? (Choose two.)

Select one or more of the following:

CODECs supported by the video units
buffer sizes on the routers
POE capabilities of the switches
number of current calls
number of hops between sites

Explanation

Question 195 of 199

1

QUESTION NO: 195
What wireless authentication option requires a Public Key Infrastructure?

Select one of the following:

EAP-TLS
PEAP
LEAP
EAP-FAST

Explanation

Question 196 of 199

1

QUESTION NO: 196
What two access point modes support the transmission of user traffic over a LWAPP/CAPWAP
tunnel? (Choose two.)

Select one or more of the following:

local
H-REAP
rogue detector
monitor
sniffer
standalone

Explanation

Question 197 of 199

1

QUESTION NO: 197
What is the primary advantage of implementing a wireless LAN controller in a wireless LAN
design?

Select one of the following:

roaming between APs
RADIUS user authentication
radio resource management
accelerated data transfer

Explanation

Question 198 of 199

1

QUESTION NO: 198
A wireless LAN client is sending traffic to the wired LAN client. What path will the packet take to
reach the destination endpoint in a lightweight wireless deployment?

Select one of the following:

switch > controller > ap > client
controller > ap > switch > client
ap > controller > switch > client
switch > ap > controller > client

Explanation

Question 199 of 199

1

QUESTION NO: 199
What Cisco product is designed to improve the performance of Windows file and exchange
services in remote data centers?

Select one of the following:

Application Control Engine
Wide Area Application Services
Cisco Application Policy Infrastructure Controller
Cisco Prime Network Services Controller

	Created by kenmike almost 9 years ago

EMULADOR DE EXAMEN

Question 1 of 199

You want to gather as much detail as possible during a network audit, to include data time stamping across a large number of interfaces, customized according to interface, with a minimal impact on the network devices themselves. Which tool would you use to meet these requirements?

Select one of the following:

Explanation

Question 2 of 199

You want to gather as much detail as possible during a network audit with a minimal impact on the network devices themselves. Which tool would you use to include data time stamping across a large number of interfaces while being customized according to each interface?

Select one of the following:

Explanation

Question 3 of 199

In which phase of PPDIOO are the network requirements identified?

Select one of the following:

Explanation

Question 4 of 199

Which is part of the Prepare phase of PPDIOO?

Select one of the following:

Explanation

Question 5 of 199

When designing the identity and access control portions for the enterprise campus network, which of these solutions would be the most appropriate solution to consider?

Select one of the following:

Explanation

Question 6 of 199

Which is the purpose of the Cisco NAC Profiler?

Select one of the following:

Explanation

Question 7 of 199

Cisco Identity-Based Networking Services relies heavily on the 802.1X protocol. Which other authentication solution is used hand-in-hand with 802.1X to authenticate users for network access?

Select one of the following:

Explanation

Question 8 of 199

Which protocol is used for voice bearer traffic?

Select one of the following:

Explanation

Question 9 of 199

Which protocol is used to reserve bandwidth for the transport of a particular application data flow across the network?

Select one of the following:

Explanation

Question 10 of 199

Which two features are supported by single wireless controller deployments? (Choose two.)

Select one or more of the following:

Explanation

Question 11 of 199

Which four services does the architecture for Media Services contain? (Choose four.)

Select one or more of the following:

Explanation

Question 12 of 199

Refer to the exhibit. Which layer is the distribution layer?

Select one of the following:

Explanation

Question 13 of 199

Which IPv6 feature enables routing to distribute connection requests to the nearest content server?

Select one of the following:

Explanation

Question 14 of 199

What is the recommended spanning tree protocol to use for all Layer 2 deployments in a branch office environment?

Select one of the following:

Explanation

Question 15 of 199

Refer to the exhibit. A standard, Layer 2 campus network design is pictured. Which numbered box represents the distribution layer?

Select one of the following:

Explanation

Question 16 of 199

Which two are types of network virtualization? (Choose two.)

Select one or more of the following:

Explanation

Question 17 of 199

You are tasked with designing a new branch office that will support 75 users with possible expansion in the future and will need a highly available network. Which of the branch design profiles should be implemented?

Select one of the following:

Explanation

Question 18 of 199

Which two can be used as a branch office WAN solution? (Choose two.)

Select one or more of the following:

Explanation

Question 19 of 199

What is the acceptable amount of one-way network delay for voice and video applications?

Select one of the following:

Explanation

Question 20 of 199

Which mode is used to exclusively look for unauthorized access points?

You want to gather as much detail as possible during a network audit, to include data time
stamping across a large number of interfaces, customized according to interface, with a minimal
impact on the network devices themselves. Which tool would you use to meet these
requirements?

You want to gather as much detail as possible during a network audit with a minimal impact on the
network devices themselves. Which tool would you use to include data time stamping across a
large number of interfaces while being customized according to each interface?

When designing the identity and access control portions for the enterprise campus network, which
of these solutions would be the most appropriate solution to consider?

Cisco Identity-Based Networking Services relies heavily on the 802.1X protocol. Which other
authentication solution is used hand-in-hand with 802.1X to authenticate users for network
access?

Which protocol is used to reserve bandwidth for the transport of a particular application data flow
across the network?

Refer to the exhibit.

Which layer is the distribution layer?

Which IPv6 feature enables routing to distribute connection requests to the nearest content
server?

What is the recommended spanning tree protocol to use for all Layer 2 deployments in a branch
office environment?

Refer to the exhibit.

A standard, Layer 2 campus network design is pictured. Which numbered box represents the
distribution layer?

You are tasked with designing a new branch office that will support 75 users with possible
expansion in the future and will need a highly available network. Which of the branch design
profiles should be implemented?

Which of the following three options represents the components of the Teleworker Solution?
(Choose three.)

Which three types of WAN topologies can be deployed in the Service Provider Module? (Choose
three.)

Which statement describes the recommended deployment of DNS and DHCP servers in the Cisco
Network Architecture for the Enterprise?

Your company's Cisco routers are operating with EIGRP. You need to join networks with an
acquisition's heterogeneous routers at 3 sites, operating with EIGRP and OSPF. Which describes
the best practice for routing protocol deployment?

Which one of these statements is an example of how trust and identity management solutions
should be deployed in the enterprise campus network?

With deterministic Wireless LAN Controller redundancy design, the different options available to
the designer have their own strengths. Which one of these statements is an example of such a
strength?

When designing the threat detection and mitigation portion for the enterprise data center network,
which of the following would be the most appropriate solution to consider?

You have a campus network that consists of only Cisco devices. You have been tasked to
discover the device platforms, the IOS versions, and an IP address of each device to map the
network. Which proprietary protocol will assist you with this task?

Which three technologies are recommended to be used for WAN connectivity in today's Enterprise
Edge designs? (Choose three.)

WAN backup over the Internet is often used to provide primary connection redundancy. Which is
the most important consideration when passing corporate traffic over the public Internet?

To provide Layer 2 connectivity between the primary and remote data centers, given that the two
data centers are using Layer 3 routed DCIs, which NX-OS technology can be used to facilitate this
requirement?

According to Cisco, which four improvements are the main benefits of the PPDIOO lifecycle
approach to network design? (Choose four.)