mrk nthny
Quiz by , created more than 1 year ago

competency Quiz on c09, created by mrk nthny on 15/08/2016.

140
1
0
mrk nthny
Created by mrk nthny over 8 years ago
Close

c09

Question 1 of 92

1

For proper air temperature control in an air conditioning system using chilled water circulation, which condition should remain constant regardless of load changes ______.

Select one of the following:

  • chilled water system supply temperature

  • compressor discharge temperature

  • squirrel cage fans are used

  • compressor suction pressure

Explanation

Question 2 of 92

1

Before doing any work on a hydraulic system equipped with accumulators, you should_______.

Select one of the following:

  • bleed off all stored energy from the accumulators

  • drain the accumulators and purge with oxygen

  • completely charge the accumulators to prevent system energy loss

  • pump the hydraulic fluid into the accumulators to prevent fluid loss

Explanation

Question 3 of 92

1

The first step when beginning to set the slide valves on a duplex reciprocating pump is to_________.

Select one of the following:

  • center the steam pistons in the cylinders

  • open the relief valve to prevent accidental starting

  • ensure the balance piston is on the downstroke

  • measure the present port openings to ensure reassembly will be the same

Explanation

Question 4 of 92

1

To safely remove the piston rod packing from the steam end of a reciprocating pump, you should_________.

Select one of the following:

  • use a packing hook

  • open the throttle valve and "blow" the old packing out

  • do nothing, as this type of pump utilizes O-rings in lieu of packing

  • open the steam chest and pry the packing loose with a scraper

Explanation

Question 5 of 92

1

In order to properly remove air from the casing of a centrifugal pump when starting, the pump should have a ______.

Select one of the following:

  • vent valve attached to the casing at the top of the volute

  • positive head

  • negative suction head

  • mechanical seal

Explanation

Question 6 of 92

1

When fire safe or fire resistant fluid is to be used in a hydraulic system, it is important that _______.

Select one of the following:

  • the fluid be compatible with all seal materials used

  • separate lube oil supply be furnished for the hydraulic pump

  • the resultant pressure, due to the increase in fluid viscosity, is not excessive

  • the fluid does not dissipate too much heat

Explanation

Question 7 of 92

1

To properly remove packing from a valve stuffing box, you should use a ________.

Select one of the following:

  • packing puller

  • sharpened rod of silver solder

  • chisel and hammer

  • screw driver

Explanation

Question 8 of 92

1

When replacing ball bearings on an electric motor shaft, you should ________.

Select one of the following:

  • apply even force to the inner race

  • tap the outer race with a mallet

  • apply even pressure to the outer race

  • apply pressure evenly to both the inner and outer races

Explanation

Question 9 of 92

1

To remove a hand held right-handed straight cut reamer after it has gone all the way through a hole, you should _____.

Select one of the following:

  • turn the tap wrench clockwise, simultaneously raising the reamer

  • tap the reamer out with a softfaced hammer

  • turn the tap wrench counterclockwise, simultaneously raising the reamer

  • work the reamer side to side to dislodge it

Explanation

Question 10 of 92

1

An acetylene pressure regulator should never be adjusted to maintain pressures exceeding (15psig) 103.4 kPa because_____.

Select one of the following:

  • this gas become extremely unstable under this condition

  • the relief valve will lift

  • the fusible plug will blowout

  • rapid depletion of acetylene is hazardous

Explanation

Question 11 of 92

1

When securing a flash-type evaporator for an extended period of time, you should______.

Select one of the following:

  • completely drain the unit

  • tightly seal the unit to exclude air

  • fill the unit with saltwater

  • fill the unit with descaling compound

Explanation

Question 12 of 92

1

Why should a person performing maintenance on an air compressor wire and tag the system valves closed?

Select one of the following:

  • To protect the operator and the equipment.

  • To prevent escape of air

  • To protect the valves

  • To prevent escape of water

Explanation

Question 13 of 92

1

Which of the following conditions can contribute to accidents?

Select one of the following:

  • Unsafe conditions

  • Good housekeeping

  • Inspections

  • Intelligent work habits

Explanation

Question 14 of 92

1

Fire doors are released by a/an__________.

Select one of the following:

  • method that automatically releases the door in the event of a disruption of control system power

  • hydraulic directional valve that automatically releases the door in the door in the event of a disruption to the control power system

  • spring-loaded catch that automatically lifts to release the door in the event of the presence of a fire

  • pneumatic heat sensor

Explanation

Question 15 of 92

1

Which of the following is an example of biological hazards?
I. Exposure to high temperatures, too high levels of relative humidity
II. Zoonotic diseases
III. Fungal diseases

Select one of the following:

  • II and III

  • I and II

  • I and III

  • I, II and III

Explanation

Question 16 of 92

1

How can ergonomics improve health and safety to the work place?
I. reduces the potential for accidents
II. reduces the potential for injury and ill health
III. improves performance and productivity

Select one of the following:

  • I, II, and III

  • I and II

  • I and III

  • II and III

Explanation

Question 17 of 92

1

Which of the following aspects that ergonomist should consider to assess the fit between person and their work?
I. the job being done and the demands on the worker
II. the equipment used
III. the senses, especially vision, hearing and touch

Select one of the following:

  • I and II

  • I and III

  • II and III

  • I, II and III

Explanation

Question 18 of 92

1

Which of the following is/are the typical ergonomics problems found in the workplace like display screen equipment?
I. The screen is poorly positioned - it is too high/low/close/far from the worker, or is offset to one side.
II. The mouse is placed too far away and requires stretching to use.
III. Chairs are properly adjusted to fit the person, forcing awkward and comfortable postures.

Select one of the following:

  • I and II

  • I and III

  • II and III

  • I, II, and III

Explanation

Question 19 of 92

1

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________.
I. they are properly grounded
II. Eye shields and gloves are worn
III. Loose clothing and jewelry are not worn

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 20 of 92

1

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________.
I. inspect the hoses for cracks and other defects
II. Remove jewelry and loose clothing
III. Bleed air pressure from the lines before breaking the connections

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 21 of 92

1

Fire prevention during welding or burning aboard any vessel should include_______.
I. Posting a fire watch in the immediate area
II. Providing an extinguisher which is ready for immediate use
III. Requiring the fire watch to remain on post for an adequate cool down period after the completion of welding of burning

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 22 of 92

1

A fire and boat drill on a tank vessel shall, by regulation, include which of the following?
I. starting the fire pumps
II. Checking fireman's outfits and other personel resuce equipment
III. Checking relevant communications equipment

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 23 of 92

1

Regulations require gears, coupling, flywheels, and all rotating machinery capable of injuring personnel to be__________.

Select one of the following:

  • Protected with adequate covers or guards

  • identified by yellow and black warning signs

  • conspicuously identified as to their particular hazard

  • located where they may not be easily contacted

Explanation

Question 24 of 92

1

Why is it that a good housekeeping on a vessel prevents fires?

Select one of the following:

  • It eliminates potential fuel sources

  • It allows better access in an emergency

  • It eliminates trip hazards

  • It improves personnel qualifications

Explanation

Question 25 of 92

1

When working around deck machinery it is a good safety practice to avoid standing in a ‘bright’ of a rope because_________.

Select one of the following:

  • a sudden yank on the line may trap your leg

  • it doesn’t allow for proper faking of the line

  • the coil may become tangled and difficult to manage

  • your work shoes may cause damage to the rope

Explanation

Question 26 of 92

1

To safeguard the operator and other personnel working on or near a hoisting operation, which of the following precautions should be observed?

Select one of the following:

  • Ensure that the lifting gear capacity is not exceeded

  • Keep a load on the hoist until all personnel are finished working

  • Set the load on a movable dolly when transportation may be needed

  • Have one man keep a hand on the load to steady it.

Explanation

Question 27 of 92

1

To prevent oily rags from spontaneously igniting, what should you do?

Select one of the following:

  • Kept in well-ventilated area and discarded as soon as possible

  • Kept in a non-metal container

  • Cleaned thoroughly for reuse

  • kept in paint locker

Explanation

Question 28 of 92

1

The knife edges and gaskets of watertight doors should be _________.

Select one of the following:

  • clean and uncoated

  • lightly coated with tallow

  • coated with petroleum jelly

  • painted to prevent weathering

Explanation

Question 29 of 92

1

Before the seas get rough, it is good safety practice to_________.

Select one of the following:

  • make a visual inspection of all engine spaces and secure loose gear

  • move quickly about the ship

  • increase all engine space lighting

  • shutdown auxiliary equipment

Explanation

Question 30 of 92

1

When a ship is expected to encounter rough seas, it is a good safety practice to ____________.

Select one of the following:

  • check for items which may become adrift and secure loose gear

  • move quickly about the ship

  • make available extra survival gear

  • maintain a negative trim on the vessel

Explanation

Question 31 of 92

1

Which of the following must be eliminated to prevent accidents?

Select one of the following:

  • Unsafe actions

  • Orderliness

  • Frequent inspections

  • Good work habit/practices

Explanation

Question 32 of 92

1

You are replacing a section of heavy piping on deck and using a chain fall to lift the pipe. Which of the following precautions should be taken to prevent personal injury?

Select one of the following:

  • Attach lines to the ends of the pipe and have your helpers steady the load

  • Position several men under the pipe so they can catch it if it falls

  • Place an old mattress under the hoist to prevent the load from hitting the deck.

  • have a first aid kit at the job site

Explanation

Question 33 of 92

1

Which of the listed conditions can be considered as the single greatest cause of accidents?

Select one of the following:

  • Human error

  • Speed

  • Excessive knowledge or skill

  • Excitement

Explanation

Question 34 of 92

1

Safety is dependent on orderliness and cleanliness. Order may be maintained by __________.

Select one of the following:

  • storing items in their assigned place

  • storing all items in a common storage container except those ready-for-sea

  • tagging all items according to their age and then storing them together

  • disposing of used items

Explanation

Question 35 of 92

1

Which of the following actions is required to be carried out during a fire drill on board?

Select one of the following:

  • Each fire pump is to be started.

  • The lifeboat is to be launched and operated

  • An inventory of rescue and fire equipment is to be taken.

  • An inspection and inventory of fire hoses is to be made

Explanation

Question 36 of 92

1

What do all portable electric tools require a ground connection?

Select one of the following:

  • To prevent electric shock if the tool is shortened

  • To prevent burning the motor from an overload

  • To prevent overloading the motor

  • To prevent grounding the plastic case through a short

Explanation

Question 37 of 92

1

Which of the following statements represents the FIRST precaution to be taken prior to working in any installed electrical component?

Select one of the following:

  • Open the supply circuits and tag the switches.

  • Water rubber gloves and boots

  • Use only approved nonconducting tools

  • Groups the case of the machine before beginning any repairs

Explanation

Question 38 of 92

1

Which practices should be followed at all times when using an electric bench grinding machine?

Select one of the following:

  • Wear google, keep support rest clearance properly adjusted to the wheel and replace grinding wheels that are chipped or unbalanced

  • Wear goggles or face shield

  • Replace grinding wheels that are chipped or unbalanced.

  • Keep the support rest clearance properly adjusted to the wheel.

Explanation

Question 39 of 92

1

Which practices should be followed at all times when using an electric grinding machine?

Select one of the following:

  • Each of the above practices

  • Wear goggles or face shield.

  • Be certain that the frame is properly grounded.

  • Be properly trained in the use of this tool

Explanation

Question 40 of 92

1

Approved buoyant work vests may be carried aboard tank vessels and shall be worn by crew members’ ____________.

Select one of the following:

  • under the supervision and control of designated ship's officers

  • when working near or over the water under unfavorable working conditions

  • as substitutes for the approved life preservers during routine drills, weather permitting, when a vessel is moored pierside

  • all of the above

Explanation

Question 41 of 92

1

When should you wear safety glasses aside from when using a hand portable grinder and scraping paint with a hand scraper?

Select one of the following:

  • Using a hammer and a chisel

  • While in port

  • During port state inspection

Explanation

Question 42 of 92

1

Machinery driving fuel oil transfer and fuel oil service pumps must be fitted with a remote means of stopping the machinery. Where is its location?

Select one of the following:

  • Outside the space concerned

  • Within the space concerned

  • The throttle station

  • Within the fireroom

Explanation

Question 43 of 92

1

What is the purpose of injury report?

Select one of the following:

  • Any of the above

  • To give the National Insurance authorities the basis for evaluating whether the personal injury or illness in question can be recognized as an occupational injury or occupational disease

  • To give the public authorities information which may be of help in the evaluation of safety issues and safety measures etc. at the workplace

  • To enable the compilation of injury/accident statistics.

Explanation

Question 44 of 92

1

What is an occupational injury?

Select one of the following:

  • injury is meant bodily injury or illness which is caused by a work accident

  • injury is meant bodily injury or illness which is caused by a leisure accident

  • either A or B

  • Neither A nor B

Explanation

Question 45 of 92

1

Which of the following is an example of biological hazard
I. Exposure to high temperatures, too high levels of relative humidity
II. Zoonotic diseases
III. Fungal diseases

Select one of the following:

  • II and III

  • I and II

  • I and III

  • I, II and III

Explanation

Question 46 of 92

1

Which of the following is an example of biological hazards?
I. Exposure to raw vegetable and animal products which may cause allergic reaction
II. Risk of poisoning while tasting food ingredients and meals at various stages of cooking
III. Risk of communicable diseases transmitted by pests, vermin, rodents, insects

Select one of the following:

  • I, II and III

  • I and II

  • I and III

  • II and III

Explanation

Question 47 of 92

1

Which of the following aspects that ergonomist should consider to assess the fit between person and their work?
I. the job being done and the demands on the worker
II. the equipment used
III. the senses, especially vision, hearing and touch

Select one of the following:

  • I and II

  • I and III

  • II and III

  • I, II and III

Explanation

Question 48 of 92

1

Which of the following aspects that ergonomist should consider the psychological aspect of a person?

Select one of the following:

  • mental abilities

  • fitness and strength

  • the social environment

  • body size and shape

Explanation

Question 49 of 92

1

Which of the following aspects that ergonomist should consider the psychological aspect of a person?

Select one of the following:

  • personality

  • the physical environment

  • the senses, especially vision, hearing and touch

  • the stresses and strains on muscles, joints, nerves

Explanation

Question 50 of 92

1

How can ergonomics improve health and safety to the work place?
I. reduces the potential for accidents
II. reduces the potential for injury and ill health
III. improves performance and productivity"

Select one of the following:

  • I, II, and III

  • I and II

  • I and III

  • II and III

Explanation

Question 51 of 92

1

Which of the following is/are the typical ergonomics problems found in the workplace like display screen equipment?
I. The screen is poorly positioned - it is too high/low/close/far from the worker, or is offset to one side.
II. The mouse is placed too far away and requires stretching to use.
III. Chairs are properly adjusted to fit the person, forcing awkward and comfortable postures.

Select one of the following:

  • I and II

  • I and III

  • II and III

  • I, II, and III

Explanation

Question 52 of 92

1

What is Chapter VIII of STCW Code?

Select one of the following:

  • Standards regarding watch keeping

  • Responsibilities of companies

  • Standards governing the use of simulator

  • Revalidation of certificate

Explanation

Question 53 of 92

1

Which practices should be followed at all times when using an electric bench grinding machine

Select one of the following:

  • All of the above

  • Wear goggles or face shield

  • Replace grinding wheels that are chipped or unbalanced.

  • Keep the support rest clearance properly adjusted to the wheel.

Explanation

Question 54 of 92

1

When a ship is expected to encounter rough seas, it is a good safety practice to ____________.

Select one of the following:

  • check for items which may become adrift and secure loose gear

  • move quickly about the ship

  • make available extra survival gear

  • maintain a negative trim on the vessel

Explanation

Question 55 of 92

1

Safety is dependent on orderliness and cleanliness. Order may be maintained by __________.

Select one of the following:

  • storing items in their assigned place

  • storing all items in a common storage container except those ready-for-sea

  • tagging all items according to their age and then storing them together

  • disposing of used items

Explanation

Question 56 of 92

1

For the protection of personnel, moving parts of rotating machinery are required to be fitted with ___________.

Select one of the following:

  • cover guards

  • audible alarms

  • bright lights

  • reflective tape

Explanation

Question 57 of 92

1

Which practices should be followed at all times when using an electric grinding machine?

Select one of the following:

  • Each of the above practices

  • Wear goggles or face shield.

  • Be certain that the frame is properly grounded.

  • Be properly trained in the use of this tool

Explanation

Question 58 of 92

1

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________.
I. they are properly grounded
II. Eye shields and gloves are worn
III. Loose clothing and jewelry are not worn

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 59 of 92

1

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________.
I. inspect the hoses for cracks and other defects
II. Remove jewelry and loose clothing
III. Bleed air pressure from the lines before breaking the connections

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 60 of 92

1

All portable electric tools should have a ground connection to prevent_________.

Select one of the following:

  • electric shock if the tool is shortened

  • burning out the motor from an overload

  • overloading the motor from a short

  • grounding the plastic case through a short

Explanation

Question 61 of 92

1

Safety glasses should be worn when_________.
I. using a hand portable grinder
II. Scraping paint with a hand scraper
III. Using a hammer and a chisel

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 62 of 92

1

Before disconnecting a joint in a pipeline, you should__________.

Select one of the following:

  • be sure no pressure exist in the line

  • Determine the size of the gasket

  • hung a bucket under the joint

  • have a first aid kit on hand

Explanation

Question 63 of 92

1

Which of the actions listed and instituted on your part will have the greatest lasting effect on the crew with respect to safety?

Select one of the following:

  • Incorporating safety practices in daily routine

  • Displaying posters illustrating safety practices

  • Showing video tapes of actual accidents

  • Publishing comprehensive safety rules

Explanation

Question 64 of 92

1

All watertight doors and watertight hatches on small passenger vessels of less than 100 gross tons required to be marked in letters __________.

Select one of the following:

  • of at least 1-inch, ‘watertight door-close in an emergency’ or ‘watertight hatch-close in emergency’

  • not to exceed 1-inch, ‘watertight door-close in emergency’ or ‘watertight hatch-close in emergency’

  • of at least 1-inch, ‘emergency exit, keep clear

  • not to exceed 1-inch, ‘emergency exit, keep clear’

Explanation

Question 65 of 92

1

According to the Regulations, all escape hatches and other emergency exits on small passenger vessels of less than 100 gross tons shall be marked on__________.

Select one of the following:

  • both sides, in at least 2-inch letters ‘emergency exit-keep clear’

  • exterior side, in less than 2-inch letters ‘watertight openning-keep clear’

  • exterior side only, in at least 2-inch letters ‘emergency exit-keep clear’

  • both sides, in at least 2-inch letters ‘watertight door-close emergency’

Explanation

Question 66 of 92

1

Regarding battery charging rooms, ventilation should be provided __________.

Select one of the following:

  • at the highest point of the room

  • at the lowest point of the room

  • horizontally near the batteries

  • only when charging is in progress

Explanation

Question 67 of 92

1

Which of the following statements represents the FIRST precaution to be taken prior to working in any installed electrical component?

Select one of the following:

  • Open the supply circuits and tag the switches.

  • Water rubber gloves and boots

  • Use only approved nonconducting tools

  • Groups the case of the machine before beginning any repairs

Explanation

Question 68 of 92

1

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out?

Select one of the following:

  • Secure and tag the supply circuit breaker in the open position.

  • De-energized the applicable switchboard bus.

  • Bypass the interlocks

  • Station a man at the circuit supply switch

Explanation

Question 69 of 92

1

Which of the following systems must be arranged so as to be energized by the final emergency power source as required by regulation?
I. at least one light in the steering gear room
II. Each power operated watertight door system
III. Each charging panel for temporary emergency batteries

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 70 of 92

1

Any abnormal condition or emergency occurring in the fireroom must be immediately reported to the _________.

Select one of the following:

  • engineer on watch

  • oiler on watch

  • first assistant engineer

  • Coast Guard

Explanation

Question 71 of 92

1

Any abnormal condition or emergency that occurs in the engine room must be reported immediately to the __________.

Select one of the following:

  • Engineer on watch

  • first assistant engineer

  • fireman on watch

  • Chief engineer

Explanation

Question 72 of 92

1

Before any work is done on a burner in an automatically fired auxiliary boiler, you should always ___________.

Select one of the following:

  • close all manually operated fuel valves

  • block all control valves

  • allow the boiler to cool completely

  • lock all safety interlock switches closed

Explanation

Question 73 of 92

1

Which of the following conditions can contribute to accidents?

Select one of the following:

  • Unsafe conditions

  • Good housekeeping

  • Inspections

  • Intelligent work habits

Explanation

Question 74 of 92

1

Good housekeeping on a vessel prevents fires by __________.

Select one of the following:

  • eliminating potential fuel sources

  • allowing better access in an emergency

  • eliminating trip hazards

  • improving personnel qualifications

Explanation

Question 75 of 92

1

Fire prevention during welding or burning aboard any vessel should include_______.
I. Posting a fire watch in the immediate area
II. Providing an extinguisher which is ready for immediate use
III. Requiring the fire watch to remain on post for an adequate cool down period after the completion of welding of burning

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 76 of 92

1

Fire doors are released by a/an__________.

Select one of the following:

  • method that automatically releases the door in the event of a disruption of control system power

  • hydraulic directional valve that automatically releases the door in the door in the event of a disruption to the control power system

  • spring-loaded catch that automatically lifts to release the door in the event of the presence of a fire

  • pneumatic heat sensor

Explanation

Question 77 of 92

1

Before the seas get rough, it is good safety practice to_________.

Select one of the following:

  • make a visual inspection of all engine spaces and secure loose gear

  • move quickly about the ship

  • increase all engine space lighting

  • shutdown auxiliary equipment

Explanation

Question 78 of 92

1

You are replacing a section of heavy piping on deck and using a chain fall to lift the pipe. Which of the following precautions should be taken to prevent personal injury?

Select one of the following:

  • Attach lines to the ends of the pipe and have your helpers steady the load

  • Position several men under the pipe so they can catch it if it falls

  • Place an old mattress under the hoist to prevent the load from hitting the deck.

  • have a first aid kit at the job site

Explanation

Question 79 of 92

1

What safety precautions should be observed by the crew while working around machinery in an engine room?
I. They should wear safety shoes
II. They should wear ear protection
III. They should not wear jewelry

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 80 of 92

1

TO safeguard the operator and other personnel working on or near a hoisting operation, which of the following precautions should be observed?

Select one of the following:

  • Insure that the lifting gear capacity is not exceeded

  • Keep a load on the hoist until all personnel are finished working

  • Set the load on a movable dolly when transportation may be needed

  • Have one man keep a hand on the load to steady it.

Explanation

Question 81 of 92

1

All exposed and dangerous areas machinery, such as gears and rotating parts, shall be properly protected with__________.

Select one of the following:

  • any of the above

  • covers

  • guards

  • rails

Explanation

Question 82 of 92

1

Regulations require gears, coupling, flywheels, and all rotating machinery capable of injuring personnel to be__________.

Select one of the following:

  • Protected with adequate covers or guards

  • identified by yellow and black warning signs

  • conspicuously identified as to their particular hazard

  • located where they may not be easily contacted

Explanation

Question 83 of 92

1

Which of the listed conditions can be considered as the single greatest cause of accidents?

Select one of the following:

  • Human error

  • Speed

  • Excessive knowledge or skill

  • Excitement

Explanation

Question 84 of 92

1

accidents are considered as an ‘unexpected contract’ you will be able to perform a better job by observing which of the following practices?
I. Looking for unsafe practices
II. Inspecting for unsafe conditions
III. Analyzing jobs for safer methods

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 85 of 92

1

Which of the following must be eliminated to prevent accidents?

Select one of the following:

  • Unsafe actions

  • Orderliness

  • Frequent inspections

  • Good work habit/practices

Explanation

Question 86 of 92

1

When working around deck machinery it is a good safety practice to avoid standing in a ‘bright’ of a rope because_________.

Select one of the following:

  • a sudden yank on the line may trap your leg

  • it doesn’t allow for proper faking of the line

  • the coil may become tangled and difficult to manage

  • your work shoes may cause damage to the rope

Explanation

Question 87 of 92

1

Who is responsible for reporting a casualty for a mobile offshore drilling unit?

Select one of the following:

  • The owner.

  • The pilot.

  • The surveyor

  • The engineer

Explanation

Question 88 of 92

1

Which of the following actions is required to be carried out during a fire drill on board?

Select one of the following:

  • Each fire pump is to be started.

  • The lifeboat is to be launched and operated

  • An inventory of rescue and fire equipment is to be taken.

  • An inspection and inventory of fire hoses is to be made

Explanation

Question 89 of 92

1

Which of the following events shall be conducted during a fire and boat drill?

Select one of the following:

  • All watertight doors which are in use while the vessel is underway shall be operated

  • All lifeboat equipment shall be examine

  • Fire pumps shall be started and all exterior outlets opened

  • All of the above

Explanation

Question 90 of 92

1

A fire and boat drill on a tank vessel shall, by regulation, include which of the following?
I. starting the fire pumps
II. Checking fireman's outfits and other personel resuce equipment
III. Checking relevant communications equipment

Select one of the following:

  • I, II & III

  • I only

  • I & II

  • II & III

Explanation

Question 91 of 92

1

Approved buoyant work vests may be carried aboard tank vessels and shall be worn by crew members’ ____________.

Select one of the following:

  • under the supervision and control of designated ship's officers

  • when working near or over the water under unfavorable working conditions

  • as substitutes for the approved life preservers during routine drills, weather permitting, when a vessel is moored pierside

  • all of the above

Explanation

Question 92 of 92

1

The knife edges and gaskets of watertight doors should be _________.

Select one of the following:

  • clean and uncoated

  • lightly coated with tallow

  • coated with petroleum jelly

  • painted to prevent weathering

Explanation

Previous
Check answer
Next