1995 State

1

What combination of switches may be used to control a light from four locations?

1

Which of the following is the standard length of electrical metallic tubing?

1

According to the National Electric Code, which of the following colors are acceptable for the grounded conductor in a circuit?

1

Which of the following is a cable type that would be appropriate to use in a barn where the conditions will be moist?

1

An "ampere" is the measurement of the?

1

The major purpose of a ground-fault interrupter is?

1

When connecting the branch circuit wires within a panel board (circuit breaker box), it is common practice to place the white wire?

1

According to the National Electric Code, when securing electrical cable to a wooden surface (ie. a stud), it is a safe practice to place ?

1

Which of the following overcurrent devices are designed to handle a "surge" of power that would occur when a large electrical load is energized?

1

The largest breaker than can be used to safely protect a 12 gauge wire is?

1

According to the National Electric Code, wall switches should be placed how many inches off the floor?

1

Electrical wiring systems are properly grounded by attaching?

1

The purpose of a transformer is to change the amount of ________ from one value to another.

1

Three phase electrical power refers to a system with?

1

The electrical device that registers the electrical energy used is the?

1

An individual circuit is one that is?

1

The NEC states that all current interrupting devices must be installed in the?

1

During the planting season, a farmer decides to recheck the plant population of his/her corn. The farmer has a 6 row-30 inch row width planter. When examining how many seeds he is planting he learns that there are 470 total seeds for the 6 rows after planting 60 feet. How many seeds per acre is the farmer supplying?

1

Operating a PTO driven air planter with underinflated tires will cause?

1

A farmer is operating his/her 12 row-30 inch planter at 6.5 mph at 85% field efficiency. How many acres will the farmer cover in a 10 hour workday?

1

How many tons per hour would a farmer bale if he/she is baling a 24' windrow that yields 2 tons/acre? Assume he/she is driving 4 mph and operating at 80% efficiency.

1

The servicing of any machine should be done?

1

Before unplugging the baler, the operator should?

1

When a safety decal becomes destroyed or lost, the operator should?

1

1000 RPM power take-off shafts are usually equipped with?

1

A common pressure range for farm field sprayer applications is?

1

Assume you are plowing a field with a 12 foot chisel plow. Your ground speed is 6 MPH. Assuming 90% efficiency, how many acres can you plow in a 10 hour day?

1

The tailings auger on a combine?

1

Timeliness losses result from a machine that is?

1

Calculate the width of a field sprayer that is able to spray 15 acres per hour while traveling at 5 mph and operating at 50% efficiency.

1

Penetration of a shovel on a row-crop cultivator is determined by?

1

The outer end of a mower cutter bar should?

1

A combine operator notices an excessive amount of threshed grain behind the straw chopper of a combine. The source of this problem could be?

1

Which of the following is not a cause of weld porosity?

1

An E6013 rod should be stored at?

1

When using reverse polarity, the electrode is?

1

When welding a thick plate in the vertical position, you should?

1

The first pass when butt welding is called?

1

Which of the following materials is safe to wear when arc welding?

1

When MIG welding, the lens shade number that should be adequate to protect your eye while welding is?

1

Which shielding gas gas allows the greatest penetration when "MIG" welding?

1

Which of the following is the primary way to adjust the amperage of a MIG welder?

1

Which type of electrical current best controls the problem of arc blow?

1

Which of the following causes the problem of undercutting when arc welding?

1

A common wire size when MIG welding is?

1

The type of current most commonly used when MIG welding is (on 95% of all applications)?

...

1995 State

What combination of switches may be used to control a light from four locations?

Which of the following is the standard length of electrical metallic tubing?

According to the National Electric Code, which of the following colors are acceptable for the grounded conductor in a circuit?

Which of the following is a cable type that would be appropriate to use in a barn where the conditions will be moist?

An "ampere" is the measurement of the?

The major purpose of a ground-fault interrupter is?

When connecting the branch circuit wires within a panel board (circuit breaker box), it is common practice to place the white wire?

According to the National Electric Code, when securing electrical cable to a wooden surface (ie. a stud), it is a safe practice to place ?

Which of the following overcurrent devices are designed to handle a "surge" of power that would occur when a large electrical load is energized?

The largest breaker than can be used to safely protect a 12 gauge wire is?

According to the National Electric Code, wall switches should be placed how many inches off the floor?

Electrical wiring systems are properly grounded by attaching?

The purpose of a transformer is to change the amount of ________ from one value to another.

Three phase electrical power refers to a system with?

The electrical device that registers the electrical energy used is the?

An individual circuit is one that is?

The NEC states that all current interrupting devices must be installed in the?

Operating a PTO driven air planter with underinflated tires will cause?

A farmer is operating his/her 12 row-30 inch planter at 6.5 mph at 85% field efficiency. How many acres will the farmer cover in a 10 hour workday?