Copiar y Editar

The NRCA Roofing Manual: Membrane Roof Systems - September RRO

Descripción

The NRCA Roofing Manual: Membrane Roof Systems - September RRO
Tommaso Costanzo
Test por Tommaso Costanzo, actualizado hace más de 1 año
Tommaso Costanzo
Creado por Tommaso Costanzo hace más de 10 años
74
0
0

Resumen del Recurso

Pregunta 1

Pregunta
The following types of roof decks are addressed in this manual:
Respuesta
  • Cementitious wood-fiber panels
  • Lightweight insulating concrete
  • Steel
  • Structural concrete (cast-in-place, post-tensioned and precast/prestressed)
  • Wood panels (plywood, oriented strand board/OSB)
  • Wood planks and wood boards
  • All of the listed are deck types addressed in the manual.

Pregunta 2

Pregunta
The International Building Code, 2009 Edition indicates a design minimum slope of _______________ is required for membrane roof systems, except for coal tar built-up roof system where a design minimum of _______________ is permitted.
Respuesta
  • 1/8:12 and 1/4:12
  • 1⁄4:12 and 1⁄8:12
  • 1⁄4:12 and 1⁄2:12
  • 1⁄4:12 and 1⁄2:24

Pregunta 3

Pregunta
Roof decks should be sloped to provide positive drainage for a finished roof system. The criterion for judging proper slope for drainage is that there be no ponding water on the roof __________ hours after a rain during conditions conducive to drying.
Respuesta
  • 4
  • 8
  • 24
  • 48

Pregunta 4

Pregunta
Following are the generic types of rigid roof insulation that are referencedin this manual and are currently among those most commonly used or found in low-slope membrane roof systems in North America:
Respuesta
  • Cellular glass and Expanded polystyrene (EPS)
  • Extruded polystyrene (XPS) and Faced gypsum
  • Fiber-reinforced gypsum and mineral fiber
  • Perlite and Polyisocyanurate (ISO)
  • High-density polyisocyanruate and Wood fiberboard
  • All of the listed are types of rigid roof insulation.

Pregunta 5

Pregunta
“Thermal Evaluation of the Effects of Gaps Between Adjacent Roof Insulation Panels” from the Proceedings of the DOE-ORNL Workshop on Mathematical Modeling of Roofs have shown that a minimum of two layers of rigid insulation can provide the following benefits to low-slope roof systems:
Respuesta
  • Increased roof system thermal performance.
  • Reduced thermal loss.
  • Reduced thermal bridging.
  • Reduced potential for membrane buckling, ridging and splitting.
  • All of the choices are correct - it is important to understand each one.

Pregunta 6

Pregunta
Most manufacturers of polyisocyanurate insulation report an R-value of 6.0 per inch of thickness based on the (LTTR) method of determination. LTTR method is defined by ASTM C1303 as the:
Respuesta
  • “Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation.”
  • “Standard Test Method for Predicting Long-Term Thermal Reflectance of Closed-Cell Foam Insulation.”
  • “Standard Test Method for Predicting Long-Term Thermal Reflectivity of Closed-Cell Foam Insulation.”
  • “Standard Test Method for Predicting Long-Term Technical Resistance of Closed-Cell Foam Insulation.”

Pregunta 7

Pregunta
Nailable Roof Decks: Mechanical fastening is a common method for attaching the first layer of high-density polyisocyanurate insulation to certain types of nailable roof decks. If a base sheet first is mechanically fastened to the deck, hot bitumen or adhesive may be used to adhere the insulation.
Respuesta
  • True
  • False

Pregunta 8

Pregunta
Non-nailable Roof Decks: Over dry, nonnailable roof decks, NRCA recommends applying high-density polyisocyanurate insulation in manufacturer-approved sealant over the properly prepared deck.
Respuesta
  • True
  • False

Pregunta 9

Pregunta
Review the image and select the correct answer:
Image:
ABC (image/jpg)
Respuesta
  • A = Side Lap, B = Exposure Lap, C = End Lap
  • A = Side Lap, B = End Lap, C = Bottom Lap
  • A = Side Lap, B = Head Lap, C = End Lap

Pregunta 10

Pregunta
Review the drawing and select the best answer about Letter A:
Image:
Presentation1 (image/jpg)
Respuesta
  • Letter A is a 2 ply configuration with a 12" or 12 9/6" exposure
  • Letter A is a 3 ply configuration with a 12" or 14 9/6" exposure
  • Letter A is a 3 ply configuration with a 17" or 18 9/16" exposure
  • Letter A is a 2 ply configuration with a 17" or 18 9/16" exposure

Pregunta 11

Pregunta
Review the drawing and select the best answer about Letter B
Image:
Presentation1 (image/jpg)
Respuesta
  • Letter B is a 2 ply configuration with a 17" or 18 9/16" exposure
  • Letter B is a 3 ply configuration with a 17" or 18 9/16" exposure
  • Letter B is a 3 ply configuration with a 11 1/3" or 12 7/16" exposure
  • Letter B is a 4 ply configuration with a 11 1/3" or 12 7/16" exposure

Pregunta 12

Pregunta
Review the drawing and select the best answer about Letter C
Image:
Presentation1 (image/jpg)
Respuesta
  • Letter C is a 4 ply configuration with a 8 1/2" or 9 5/16" exposure
  • Letter C is a 3 ply configuration with a 8 1/2" or 9 5/16" exposure
  • Letter C is a 3 ply configuration with a 9" or 12" exposure
  • Letter C is a 4 ply configuration with a 9" or 12" exposure

Pregunta 13

Pregunta
The following general recommendation for recovering over an existing roof system with a new built-up, polymer-modified bitumen, single-ply or liquid-applied membrane roof system should be considered:
Respuesta
  • The existing roof system and new re-cover roof system must be compatible or appropriately separated.
  • The roof deck should be secured to the structure of the building, support the design live load and dead load required for the building, and provide the necessary pullout resistance for fasteners used with a new mechanically attached re-cover roof system.
  • If the new roof system is fully adhered to the existing roof system, the existing roof membrane and insulation, if any, should be secured to the roof deck according to appropriate wind uplift resistance requirements. The surface of the existing roof system may require preparation and/or may need to be primed with a compatible primer to enhance adhesion before application of the new adhered roof system.
  • The existing roof system should be inspected and tested, if necessary, to determine whether excess moisture is present within the roof assembly. Wet insulation must be removed and replaced with compatible materials.
  • The existing roof system should be inspected for shrinkage, ridging, splitting and cracking and then repaired appropriately. Portions that may present problems should be secured or removed.
  • All of these are general recommendations that should be considered.

Pregunta 14

Pregunta
Review the image and choose the correct answer:
Image:
FLASH (image/jpg)
Respuesta
  • A = 6", B = 12" and C = 12
  • A = 6", B = 6" and C = 12"
  • A = 12", B = 12" and C = 24"
  • A = 12", B = 24" and C = 24"

Pregunta 15

Pregunta
Review the image and choose the correct answer:
Image:
8_Red (image/jpg)
Respuesta
  • A = 8", B = 8", C = 8"
  • A = 12", B = 8", C = 8"
  • A = 12", B = 12", C = 8"
  • A = 8", B = 8", C = 4"

Pregunta 16

Pregunta
Review the image and choose the correct answer about A
Image:
Presentation1 (image/jpg)
Respuesta
  • 2 1/2 LB. lead or 16 oz. soft copper
  • 20" square minimum, 2 1/2 LB. lead or 16 oz. soft copper
  • 30" square minimum, 2 1/2 LB. lead or 12 oz. soft copper
  • 30" square minimum, 2 1/2 LB. lead or 16 oz. soft copper

Pregunta 17

Pregunta
Review the image. Letter A should say:
Image:
Presentation1 (image/jpg)
Respuesta
  • Sheet metal gutter - The front of the gutter should be a min. 1/2" lower than the back to allow for overflow. Refer to the architectural metal flashing section of the NRCA roofing manual: Architectural Metal Flashing, Condensation Control and Re-Roofing - 2010 for other shapes.
  • Sheet metal gutter - The front of the gutter should be a min. 1" lower than the back to allow for overflow. Refer to the architectural metal flashing section of the NRCA roofing manual: Architectural Metal Flashing, Condensation Control and Re-Roofing - 2010 for other shapes.
  • Sheet metal gutter - The front of the gutter should be a min. 2" lower than the back to allow for overflow. Refer to the architectural metal flashing section of the NRCA roofing manual: Architectural Metal Flashing, Condensation Control and Re-Roofing - 2010 for other shapes.
  • Sheet metal gutter - The front of the gutter should be a min. 3" lower than the back to allow for overflow. Refer to the architectural metal flashing section of the NRCA roofing manual: Architectural Metal Flashing, Condensation Control and Re-Roofing - 2010 for other shapes.

Pregunta 18

Pregunta
Base Sheets and Ply Sheets include all of the following EXCEPT:
Respuesta
  • Asphalt-coated Fiberglass-mat Base Sheet:
  • Asphalt-coated Fiberglass Venting Base Sheets:
  • Asphalt Fiberglass Ply Sheets:
  • Coal Tar Impregnated Fiberglass Ply Sheet:
  • Asphalt-coated Fiberglass Cap Sheet Surfaced With Mineral Granules:

Pregunta 19

Pregunta
Membrane flashings typically consist of a base or backer layer or layers and a cap sheet. The following are types of modified bitumen membranes - EXCEPT:
Respuesta
  • SBS Polymer-modified Bitumen Base Sheets
  • SBS Polymer-modified Bitumen Cap Sheets
  • Ethylene Propylene Diene Monomer Sheets
  • APP Polymer-modified Bitumen Sheets

Pregunta 20

Pregunta
There are two broad types of single-ply membranes based on their chemistry: thermoset single-ply membranes and thermoplastic single-ply membranes.
Respuesta
  • True
  • False
Mostrar resumen completo Ocultar resumen completo

¿Quieres crear tus propios Tests gratis con GoConqr? Más información.

Similar

La narrativa hispanoamericana
ignaciobll
CUESTIONARIO DE FÍSICA
amam3105
Test Primera Guerra Mundial
juanmadj
METABOLISMO DE LOS LÍPIDOS
Diego Santos
20 preguntas sobre sistemas operativos
esmeraldameza100
VOCALES. Diptongo o Hiato...
JL Cadenas
Contabilidad de Costos
leodavidpb
Alemán Básico
Virginia León
Consecuencias de la Expansión Europea (siglo XV-XVI)
María Fernanda Arona Cabrera
2o Parcial.- 1er Simulador de Anatomía del 1er año de Medicina
Mario Alberto Solis Villanueva
FASES PROCEDIMIENTO ADMTVO
Lauriña Gomez Martin
Explorar la Librería