13655799
Descripción
Test por Jarmo Tossavainen, actualizado hace más de 1 año
|
Creado por Jarmo Tossavainen
hace más de 6 años
|
|
Pregunta 1
Pregunta
1/ Which part of the Building Regulations deals with the energy efficient
installation of central heating systems in domestic properties?
Respuesta
-
a) Part G
-
b) Part L1
-
c) Part L2
-
d) Part M
Pregunta 2
Pregunta
2/ Details of the heat output requirement for a particular radiator can be found in
which of the following documents?
Respuesta
-
a) British Standards
-
b) Water Regulations
-
c) Building Regulations
-
d) Manufacturer’s brochure
Pregunta 3
Pregunta
3/ What is the likely outcome of rigidly fixing central heating pipework to the
notched sections in timber first floor joists?
Respuesta
-
a) Rupture of the pipework
-
b) A reduction in energy efficiency
-
c) Corrosion of the pipework
-
d) Expansion and contraction noise
Pregunta 4
Pregunta
4/ The main disadvantage of using a one pipe circuit to the radiators in a central
heating system is that –
Respuesta
-
a) The last radiator on the circuit will be fed with water at a lower temperature than the first
-
b) The first radiator on the circuit will be fed with water at a lower temperature than the last
-
c) Pipework feeding all radiators must be 22mm in diameter
-
d) The circuit cannot be pumped, gravity circulation must be used
Pregunta 5
Pregunta
5/ Which fully pumped central heating system control component is missing from
` the following diagram?
Respuesta
-
a) Pump
-
b) Cylinder thermostat
-
c) Room thermostat
-
d) Mid-position valve
Pregunta 6
Pregunta
6/ What is the minimum size of open vent pipe to a fully pumped central heating
system in a small domestic property?
Respuesta
-
a) 10mm
-
b) 15mm
-
c) 22mm
-
d) 28mm
Pregunta 7
Pregunta
7/ Which one of the following additional components will require to be installed
when replacing a single feed indirect cylinder with a double feed indirect
cylinder?
Respuesta
-
a) Frost thermostat
-
b) Feed and expansion cistern
-
c) Cold water storage cistern
-
d) Automatic bypass valve
Pregunta 8
Pregunta
What would be the main effect on the central heating system
if the circulator was installed in the position shown in this diagram?
Respuesta
-
a. The system would be under negative pressure
-
b. The system would be mostly under negative pressure
-
c. The system would be pumping over the open vent
-
d. The neutral position would be at the base of the open vent.
Pregunta 9
Pregunta
The feed and expansion cistern in an open vented central heating system
should be capable of receiving what percentage volume of water from the
heating system when heated –
Respuesta
-
a) 2%
-
b) 4%
-
c) 8%
-
d) 16%
Pregunta 10
Pregunta
The recommended vertical height from floor level to the position of a room
thermostat is –
Respuesta
-
a) 1.0m
-
b) 1.5m
-
c) 2.0m
-
d) 2.5m
Pregunta 11
Pregunta
Which air separator port in the following diagram is the flow pipe from the
boiler connected to?
Respuesta
-
a) Port 1
-
b) Port 2
-
c) Port 3
-
d) Port 4
Pregunta 12
Pregunta
Which of the following statements is correct in relation to the installation of
thermostatic radiator valves?
Respuesta
-
a) Thermostatic radiator valves may only be fitted to ground floor radiators in a property
-
b) Thermostatic radiator valves may only be fitted to first floor radiators in a property
-
c) All radiators in a property should be fitted with thermostatic radiator valves
-
d) At least one radiator in a property should be fitted without a thermostatic radiator valve
Pregunta 13
Pregunta
Which pipe connects to the AB port of the mid-position valve in the following
diagram?
Respuesta
-
a) Open vent pipe
-
b) Flow pipe to the cylinder
-
c) Return pipe from the cylinder
-
d) Flow pipe from the pump
Pregunta 14
Pregunta
Which of the following components is fitted at the high points in pipework in
central heating systems?
Respuesta
-
a) Automatic air vent
-
b) Non-return valve
-
c) Automatic bypass valve
-
d) Drain valve
Pregunta 15
Pregunta
Central heating systems with metallic pipework materials are normally
soundness tested to what test pressure?
Respuesta
-
a) 0.5 times the maximum operating pressure
-
b) The maximum operating pressure
-
c) 1.5 times the maximum operating pressure
-
d) Twice the maximum operating pressure
Pregunta 16
Pregunta
Which of the following is part of the commissioning procedure for a new
central heating system?
Respuesta
-
a) Hot flushing to assist with flux removal
-
b) Disinfecting the system with chlorine
-
c) Removing the feed & expansion cistern during filling
-
d) Lubricating the circulating pump with oil
Pregunta 17
Pregunta
When replacing a radiator and its associated valves sited on the first floor of a
property which is the most efficient way of draining the water to undertake the
work?
Respuesta
-
a) Turn off the valves and drain down the radiator
-
b) Completely drain the whole system
-
c) Drain the system to below the first floor
-
d) Isolate the cistern and empty its contents
Pregunta 18
Pregunta
The safest method of ensuring that the electrical controls in a central heating
system cannot be re-activated during temporary decommissioning work is to –
Respuesta
-
a) Isolate the system from the supply at the consumer unit and get on with the work
-
b) Switch off the supply to the system at the fused spur, retain the fuse and check for safe isolation
-
c) Switch off the supply to the system at the fused spur and check for safe isolation
-
d) Switch off the fused spur remove the wires from its outlet and tape up the ends
Pregunta 19
Pregunta
What is the likely problem arising from a bypass not being fitted to an open
vented close-coupled fully pumped heating system controlled by 2 x two port
valves on the heating and hot water circuits?
Respuesta
-
a) ‘Sucking down’ and ‘pumping over’ the open vent pipe
-
b) Blockage occurring in the cold feed pipe
-
c) Rapid pinhole corrosion of the radiators
-
d) No cool water from the f & e cistern if the system overheats
Pregunta 20
Pregunta
Which of the following central heating components may contain a replaceable
packing gland?
Respuesta
-
a) Circulating pump
-
b) Automatic air vent
-
c) Thermostatic radiator valve
-
d) Room thermostat
¿Quieres crear tus propios Tests gratis con GoConqr? Más información.