3501362
Descripción
Test por nicilynn1981, actualizado hace más de 1 año
|
Creado por nicilynn1981
hace alrededor de 9 años
|
|
Pregunta 1
Pregunta
Risk management principles should be applied to
Respuesta
-
Only duty-related activities to enhance the safety and well-being of yourself and others.
-
On- and off-duty activities to enhance the safety and well-being of yourself and others.
-
Only duty-related activities to protect yourself and other Airmen from imminent harm.
-
On- and off-duty activities to protect yourself and other Airmen from imminent harm.
Pregunta 2
Pregunta
What situation does not warrant prompt reporting to your supervisor?
Respuesta
-
Using personal protective equipment.
-
Unsafe working conditions.
-
Known pregnancies.
-
Personal injury.
Pregunta 3
Pregunta
Before removing a component from an air compressor, you must ensure
Respuesta
-
The air compressor is grounded.
-
The air strainer is in place.
-
The battery is disconnected.
-
All air pressure is drained.
Pregunta 4
Pregunta
Why should the frame of an electrical motor be grounded?
Respuesta
-
To prevent the energized windings from touching the frame.
-
To prevent current from following the path of least resistance.
-
To prevent you from receiving an electrical shock if the energized windings touch the frame.
-
To prevent current from flowing directly to ground if the energized windings touch the frame.
Pregunta 5
Pregunta
Which type of hammer should you use to avoid damaging driving materials?
Respuesta
-
Claw
-
Sledge
-
Soft face
-
Ball-peen
Pregunta 6
Pregunta
Which type of screwdriver has blades designed to lessen the possibility of the screwdriver slipping from the screw head?
Respuesta
-
Cross-point.
-
Flat-blade.
-
Cross-tip.
-
Offset
Pregunta 7
Pregunta
Which pliers should be used to hold odd-shaped objects?
Respuesta
-
Snap ring.
-
Diagonal cutting.
-
Multiple slip-joint.
-
Combination slip-joint
Pregunta 8
Pregunta
Which pliers have a locking device to hold materials securely?
Respuesta
-
Snap ring.
-
Vice grips.
-
Water pump.
-
Diagonal cutters.
Pregunta 9
Pregunta
Diagonal cutting pliers are designed to cut
Respuesta
-
Bolts
-
Rivets
-
Hard steel
-
Small wire
Pregunta 10
Pregunta
Before operating the pneumatic impact wrench, you must
Respuesta
-
Inspect it
-
Lubricate it
-
Blow out the air hose
-
Ensure that its use is necessary
Pregunta 11
Pregunta
Replacement hardware decisions on support equipment must be governed by
Respuesta
-
Supervisor's preference
-
Serviceablility criteria
-
Cosmetic appearance
-
Availability
Pregunta 12
Pregunta
What type of bolt is typically used to connect accessories to an engine?
Respuesta
-
Stud
-
Fine thread bolt
-
Coarse thread bolt
-
General purpose bolt
Pregunta 13
Pregunta
What type of nut should never be used in areas where the temperature exceeds 250 degrees Fahrenheit?
Respuesta
-
Nonmetallic self-locking nuts
-
Metallic self-locking nuts
-
Castellated nuts
-
Plain nuts
Pregunta 14
Pregunta
What color code is used on pre-insulated terminal lugs for wire sizes 18 through 22?
Respuesta
-
Red
-
Blue
-
Green
-
Yellow
Pregunta 15
Pregunta
What are the three different types of terminal lugs?
Respuesta
-
Red, Blue & Yellow
-
Straight, Right Angle & Flat
-
Copper, Aluminum & Plastic
-
Pre-insulated, uninsulated & reinsulated
Pregunta 16
Pregunta
What does the “-4” identify in fitting part number MS20822-4D?
Respuesta
-
Military specification
-
Type of fitting
-
Air Force/Navy
-
Fitting size
Pregunta 17
Pregunta
What type of damage greatly reduces the ability of tubing to withstand internal pressure and vibration?
Respuesta
-
Scratches
-
Chafing
-
Dents
-
Nicks
Pregunta 18
Pregunta
A flexible hose in a 3,000 psi system must be pressure tested to
Respuesta
-
3,000 psi without bursting
-
9,000 psi without bursting
-
12,000 psi without bursting
-
15,000 psi without bursting
Pregunta 19
Pregunta
When installing a flexible hose, you must provide slack or bend in the hose to
Respuesta
-
Prevent twisting of the hose
-
Compensate for change in length
-
Place a mechanical load on the hose
-
Protect it from a hot pipe or manifold
Pregunta 20
Pregunta
How can people best prevent FOD?
Respuesta
-
Look for loose objects (stone, paper, or trash), pick them up when discovered, and encourage others to do the same.
-
Learn the basic classes of FOD, recognize its causes, and account for tools and hardware used during maintenance.
-
Look for loose objects discarded on the flight line during maintenance activities.
-
Periodically participate in “FOD walks” on taxiways and runways.
Pregunta 21
Pregunta
You need to find all of the TOs for a specific weapon system or piece of equipment. What type of index should you use?
Respuesta
-
TO catalog
-
Alphabetical index
-
Cross-reference table
-
LOAPs
Pregunta 22
Pregunta
You need to find the part number for an item prior to ordering it from supply. You’ve obtained the appropriate IPB manual for the end-item. What section of the IPB should you use to find the major assembly to which the desired item belongs?
Respuesta
-
Table of Contents
-
Reference designator index
-
Appropriate figure/illustration
-
National stock number and reference number index
Pregunta 23
Pregunta
Which TCTO is issued to correct unsafe conditions that, if not corrected, could result in serious or fatal injury to personnel?
Respuesta
-
Saftey
-
Urgent Action
-
Routine Action
-
Immediate Action
Pregunta 24
Pregunta
What type of TCTO is often accomplished by contractors, modification centers, or specific Air Force activities higher than organizational\intermediate-level maintenance due to the complexity involved?
Respuesta
-
Abbreviated TCTO.
-
Inspection TCTO.
-
Record TCTO.
-
Interim TCTO.
Pregunta 25
Pregunta
The main advantage of using abbreviated TOs is they
Respuesta
-
Cover safety in more detail
-
Serve as supplemental material
-
Paraphrase and eliminate the need for basic TOs
-
Organize and simplify instructions in a condensed version
Pregunta 26
Pregunta
Periodic inspection work cards are divided into three sections that cover the requirements for
Respuesta
-
Periodic inspections, lubrication, and special inspections.
-
Periodic inspections, special inspections, and safety.
-
Periodic inspections, lubrication, and safety.
-
Special inspections, lubrication, and safety.
Pregunta 27
Pregunta
Which abbreviated TO provides guidance for checking the general serviceability of a piece of equipment including applicable safety warnings, cautions, and notes?
Respuesta
-
Lubrication charts
-
Illustrated parts breakdown
-
Service inspection work cards
-
Periodic inspection work cards
Pregunta 28
Pregunta
An example of a TO deficiency is
Respuesta
-
Improper sequencing of pages
-
Insufficient information
-
Typographical errors
-
Misspelled words
Pregunta 29
Pregunta
Which form should you submit to correct a TO deficiency?
Respuesta
-
AFTO Form 1000, Deficiency Report.
-
AFTO Form 601A, Change Recommendation
-
AFTO Form 95, Support Equipment Record
-
AFTO Form 22, Technical Manual ™ Change Recommendation and Reply
Pregunta 30
Pregunta
What are the two general classes of Air Force publications?
Respuesta
-
Pamphlets and manuals
-
Departmental and field
-
Instructions and manuals
-
Supplements and instructions
Pregunta 31
Pregunta
OIs are similar to Air Force instructions, but they apply only to
Respuesta
-
Air Force wings
-
Support personnel
-
Maintenance personnel
-
Personnel within the issuing organization
Pregunta 32
Pregunta
What type of standard publication is used by lower headquarters to implement, amplify, interpret, or clarify a higher level publication?
Respuesta
-
Supplements
-
Visual aids
-
Bulletins
-
Manuals
Pregunta 33
Pregunta
The first number of a standard Air Force publication number is referred to as the “series” and represents the
Respuesta
-
Broad area covered
-
Specific area covered
-
Specific title of the publication
-
Specific military personnel affected
Pregunta 34
Pregunta
Where do you access standard Air Force publications?
Respuesta
-
Air Force e-Publishing website.
-
LOAPs
-
Base-level functional publication library
-
AFI 33–360
Pregunta 35
Pregunta
What impact is made on the maintenance organization by ensuring availability of adequate parts, equipment, and training?
Respuesta
-
Increasing bottlenecks and maximizing repair cycle time
-
Increasing bottlenecks and minimizing repair cycle time
-
Eliminating bottlenecks and minimizing repair cycle time
-
Eliminating bottlenecks and maximizing repair cycle time
Pregunta 36
Pregunta
Which maintenance levels are considered together as “field maintenance”?
Respuesta
-
Centralized and depot
-
Depot and provisional
-
Provisional and centralized
-
Organizational and intermediate
Pregunta 37
Pregunta
Organizational maintenance consists of
Respuesta
-
On-equipment tasks normally performed using the resources of an operating command at an operating location.
-
On-equipment tasks normally performed using the resources of a supporting command or intermediate repair facility.
-
Off-equipment tasks normally performed using the resources of an operating command at an operating location or intermediate repair facility.
-
On- or off-equipment tasks that require highly specialized skills, sophisticated shop equipment, and/or special facilities of a supporting command
Pregunta 38
Pregunta
The main purpose of the inspection system is to
Respuesta
-
Get ahead on unscheduled maintenance
-
Keep equipment operating and looking good
-
Keeping the mechanic working on minor problems
-
Locate problems and repair equipment before total failure
Pregunta 39
Pregunta
The maintenance symbol the represents the most serious operational condition for equipment is a
Respuesta
-
Rex X
-
Red Dash
-
Red Diagonal
-
Circled Red X
Pregunta 40
Pregunta
Which symbol indicates an operational check is overdue?
Respuesta
-
Red X
-
Red Dash
-
Red Diagonal
-
Circled Red X
Pregunta 41
Pregunta
Which section of the AFTO Form 244 is used to record a forms review?
Respuesta
-
Part II, Non-scheduled Inspection
-
Part III, Scheduled Inspection
-
Part IV, Supervisory Review
-
Part V, Maintenance/Delayed Discrepancy
Pregunta 42
Pregunta
When closing out an AFTO Form 244, what is entered on the form to close out uncompleted inspections?
Respuesta
-
A red X and your initials in Part IV, Supervisory Review
-
A red X and your initials in Part III, Scheduled Inspections
-
The letters “CF” (for carried forward) and your initials in Part IV, Supervisory Review
-
The letters “CF” (for carried forward) and your initials in Part III, Scheduled Inspections
Pregunta 43
Pregunta
What is the condition of a component bearing a green equipment condition label?
Respuesta
-
Unserviceable (Condemned)
-
Unserviceable (Repairable)
-
Serviceable
-
Suspended
Pregunta 44
Pregunta
What color is the equipment condition tag attached to an item being held as an exhibit?
Respuesta
-
Brown
-
Green
-
White
-
Yellow
Pregunta 45
Pregunta
What maintenance supply form is used to order commonly stocked supplies or turn in excess or unserviceable property?
Respuesta
-
AF Form 2005
-
AFTO Form 350
-
DD Form 1348-6
-
DD Form 1348-1A
Pregunta 46
Pregunta
What MDD code identifies the system that was worked on?
Respuesta
-
Type maintenance
-
Work unit code
-
Category of labor
-
Units
Pregunta 47
Pregunta
Distinguish between “excess” and “surplus” as they apply to Air Force supply discipline.
Respuesta
-
Excess and surplus are the same.
-
Excess and surplus are the turn-in of property no longer needed.
-
Surplus is property no longer needed at your base, and excess is property no longer needed by another military service or Federal agency.
-
Excess is property no longer needed at your base, and surplus is property no longer needed by another military service or Federal agency.
Pregunta 48
Pregunta
What is a major concept regarding “economic use” of supplies and equipment?
Respuesta
-
Use them only for their intended purposes.
-
Always order the least expensive item to do the job.
-
Protect items from hazards such as fire or corrosion.
-
Order only the minimum supplies necessary to do a job.
Pregunta 49
Pregunta
Who is responsible for ensuring that property records of supply transactions are kept accurately?
Respuesta
-
Commander
-
Supervisor
-
Person who signed for an account
-
Person who has possession of the property
Pregunta 50
Pregunta
To be held responsible for property, you must
Respuesta
-
Possess it
-
Sign for it
-
Be a 5 level
-
Be a supervisor
Pregunta 51
Pregunta
What are you required to do with Air Force property you might find and believe it to be lost or misplaced?
Respuesta
-
Leave it where you found it
-
Place it back into the supply system.
-
Take the item to the organizational commander.
-
Take it to the security forces lost and found section.
Pregunta 52
Pregunta
What equipment does not require an AFTO Form 375?
Respuesta
-
Items less than $2,500
-
Items less than $25,000
-
Items more than $2,500
-
Items more than $25,000
Pregunta 53
Pregunta
Items that retain their identity throughout the period of their use and may be turned in and reissued for use by others are considered
Respuesta
-
DIFM
-
Excess
-
Expendable
-
Nonexpendable
Pregunta 54
Pregunta
When the bench stock quantity level falls below 50 % for an item, you should
Respuesta
-
Post a due-out list
-
Place a red tag on the bin
-
Notify supply that stock level is low
-
Initial the initial supply stock listing
Pregunta 55
Pregunta
The responsibility of a person to make good any loss, destruction, or damage of government property caused by misuse or neglect is what kind of liability?
Respuesta
-
Property
-
Personal
-
Pecuniary
-
Command
Pregunta 56
Pregunta
How can a person be relieved from property responsibility other than by pecuniary liability?
Respuesta
-
Turn-in only
-
Transfer only
-
Turn-in or Transfer
-
Cash collection voucher or statement of charges
Pregunta 57
Pregunta
A statement of charges would be prepared under which of these circumstances?
Respuesta
-
If a lost item is not expendable
-
If you make a cash payment for a lost item
-
If you signed a hand receipt for a lost item
-
If you want to use payroll deduction to pay the cost of a lost item
Pregunta 58
Pregunta
What must be done if SSgt Ortiz refuses to admit pecuniary liability for the loss of a $275 lawn mower for which he has custodial responsibility?
Respuesta
-
A report of survey must be initiated.
-
A statement of charges must be prepared.
-
Charges must be made on a military pay order.
-
The mower must be replaced by one of equivalent value.
Pregunta 59
Pregunta
After a deficiency has been discovered, when must a category II PQDR be submitted to the screening point?
Respuesta
-
24 hours
-
2 calendar days
-
5 calendar days
-
10 calendar days
Pregunta 60
Pregunta
Within the deficiency reporting system, who is responsible for the resolution of the deficiency?
Respuesta
-
Originating point
-
Screening point
-
Action point
-
Support point
Pregunta 61
Pregunta
Within the deficiency reporting system, who assigns a report control number and ensures proper marking and handling of exhibits?
Respuesta
-
Originating point
-
Screening point
-
Action point
-
Support point
Pregunta 62
Pregunta
Who should AGE maintainers contact for submittal format of agenda items when preparing for the PIWG?
Respuesta
-
MAJCOM AGE functional managers
-
Screening point within the originating activity
-
Lead command (AFMC)
-
WR-ALC
Pregunta 63
Pregunta
On which type of metal can you leave corrosion as long as the component is operational?
Respuesta
-
Steel
-
Copper
-
Aluminum
-
None, all corrosion must be removed.
Pregunta 64
Pregunta
What marking is applied to AGE for night safety?
Respuesta
-
Informational
-
Safety/Danger
-
Reflectorization
-
Caution/Warning
Pregunta 65
Pregunta
Guidelines for storing AGE are in
Respuesta
-
TO 35-1-3
-
TO 35-1-4
-
TO 35-1-12
-
AFMAN 23-110
Pregunta 66
Pregunta
Which of these items must be removed from test equipment before storage?
Respuesta
-
Wet and dry cell batteries
-
Dry charge batteries
-
Battery compartment
-
Battery holder
Pregunta 67
Pregunta
What AGE must have the fuel drained when preparing it for mobility?
Respuesta
-
Equipment with fuel levels that cannot be verified
-
Self-propelled equipment required for immediate use at deployment sites
-
Equipment that is not self-propelled and is required for immediate use at deployment sites
-
All AGE must have fuel drained prior to deployment; there are no exceptions
Pregunta 68
Pregunta
During a battery condition check, what is an acceptable voltage reading for a 12-volt battery?
Respuesta
-
8–2 volts
-
10–12 volts
-
12.4 volts or lower
-
12.7 volts or higher
Pregunta 69
Pregunta
After connecting a voltmeter across the starter terminals and clamping a current probe around the positive battery cable, what must be done prior to cranking the engine when performing a starting system check on AGE?
Respuesta
-
Estimate the temperature of the battery.
-
Prevent the engine from starting.
-
Perform a battery cable test.
-
Disconnect the voltmeter.
Pregunta 70
Pregunta
How should you approach a parked aircraft with your vehicle?
Respuesta
-
Only when a guide is posted.
-
Within 25 feet of an aircraft with engines running
-
With the driver’s side of the vehicle toward the aircraft
-
With the driver’s side of the vehicle away from the aircraft
Pregunta 71
Pregunta
What should you do if your vehicle meets a moving aircraft at night?
Respuesta
-
Turn off your headlights and leave your parking lights on.
-
Dim your headlights and continue on.
-
Stop and change directions.
-
Turn all lights off.
Pregunta 72
Pregunta
Why should you apply silicone sealant to the valve stem area of a wheel?
Respuesta
-
To keep rims from flying apart
-
To keep water from entering rims
-
As a treatment for weather cracks
-
As a treatment for severe corrosion
Pregunta 73
Pregunta
What must you do before inflating the inner tube fully on a split rim tire?
Respuesta
-
Fully deflate the tire
-
Torque wheel lug bolts
-
Check tires for foreign objects
-
Ensure rims are completely bolted together and torqued.
¿Quieres crear tus propios Tests gratis con GoConqr? Más información.