Copiar y Editar

Millwright Test 1

Descripción

Millwright CofQ Millwright Exam Prep. Test sobre Millwright Test 1, creado por Lukasz N el 08/04/2022.
Lukasz N
Test por Lukasz N, actualizado hace 8 meses
Lukasz N
Creado por Lukasz N hace más de 2 años
3
0
0

Resumen del Recurso

Pregunta 1

Pregunta
What Part and Section of the OHS Code describes the membership of a joint work site health and safety committee?
Respuesta
  • Part 12, Section 197
  • Part 13, Section 197
  • Part 14, Section 197
  • Part 15, Section 197

Pregunta 2

Pregunta
What Part and Section of the OHS Code describes the requirements and options for protective footwear?
Respuesta
  • Part 18, Section 229
  • Part 18, Section 232
  • Part 18, Section 233
  • Part 18, Section 236

Pregunta 3

Pregunta
What Part and Section of the OHS Code describes the requirements and options for worker training about WHMIS?
Respuesta
  • Part 29, Section 394
  • Part 29, Section 395
  • Part 29, Section 396
  • Part 29, Section 397

Pregunta 4

Pregunta
What are the first aid requirements for high hazard work at a close work site with 5 to 9 workers at the work site per shift?
Respuesta
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 3 First Aid Kit, 3 blankets, stretcher, splint
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit

Pregunta 5

Pregunta
What is employer responsibility with regard to hazard assessment at the work site?
Respuesta
  • to provide easy and immediate access for any worker to the OHS Act, Regulation and Code at the work site
  • to ensure suppliers are aware of their responsibility to provide necessary information on any hazards related to their products
  • to develop a plan to eliminate or control any hazard identified at the work site
  • to ensure all workers participate in daily meetings to inspect their tools and plan their work

Pregunta 6

Pregunta
How is Workers Compensation Board of Alberta funded?
Respuesta
  • 100% of the funding for the WCB comes from employers in Alberta.
  • 75% of the funding for the WCB comes from employers and 25% comes from the provincial government
  • 50% of the funding for the WCB comes from employers, 25% from the provincial government and 25% from employees
  • 33% of the funding for the WCB comes from employers, 34% from the provincial government and 33% from employees

Pregunta 7

Pregunta
What are the four categories of workplace hazards?
Respuesta
  • ecological, chemical, ergonomic, physical
  • biological, chemical, ergonomic, physical
  • biological, ecological, chemical, physical
  • chemical, physical, psychological, ecological

Pregunta 8

Pregunta
What is an example of an engineering control for worker protection?
Respuesta
  • renovation
  • subdivision
  • isolation
  • activation

Pregunta 9

Pregunta
When is an administrative control put in place for worker protection?
Respuesta
  • To identify the correct personal protective equipment to be used in a hazardous situation
  • To document the details of the implementation of an engineering control
  • When an engineering control cannot eliminate or control a hazard
  • To isolate a hazard through containment or enclosure

Pregunta 10

Pregunta
Who is responsible to have an emergency response plan in place at work site?
Respuesta
  • employees
  • OHS inspector
  • joint work site health and safety committee
  • employers

Pregunta 11

Pregunta
What part of the OHS Code convers first aid requirements at the work site?
Respuesta
  • Part 10
  • Part 11
  • Part 12
  • Part 13

Pregunta 12

Pregunta
What must your employer do if first aid supplies are stored in secure containers at the work site?
Respuesta
  • Ensure the containers are clearly marked to indicate their contents
  • Ensure the containers are stored in a dust proof environment
  • Ensure the containers are not stacked more than 3 layers high
  • Ensure the containers are inspected monthly to ensure contents are safe

Pregunta 13

Pregunta
What number and type of first aiders must your employer ensure are present at an isolated work site with low hazard assessment rating and 65 workers at the work site per shift?
Respuesta
  • 1 Standard First Aider
  • 1 Standard First Aider and 1 Emergency First Aider
  • 2 Standard First Aiders
  • 2 Standard First Aiders and 1 Emergency First Aider

Pregunta 14

Pregunta
What is the duty to use personal protective equipment according to the Alberta OHS Code?
Respuesta
  • a clause that must be included in the employment contract of every construction worker in Alberta
  • a sign that must be posted at the entrance to any work site where PPE is required
  • the part of the OHS Code that describes the different types of PPE to be used on the work site
  • what you and your employer must do if a hazard assessment identifies the need for the use of PPE

Pregunta 15

Pregunta
Who is responsible to ensure work site emergency response plans remain up to date?
Respuesta
  • the employer
  • the employer and the employees
  • the employees
  • the OHS inspector

Pregunta 16

Pregunta
When a work site hazard assessment identifies that workers are required to wear PPE what is your employer's responsibility?
Respuesta
  • Ensure all workers are informed about the need to wear PPE
  • Ensure all workers properly use and wear the required PPE
  • Put up posters indicating a hazard assessment has identified that PPE is required
  • Ensure all workers are provided with funding to purchase required PPE

Pregunta 17

Pregunta
What is an employee responsibility with regard to the use of PPE?
Respuesta
  • to inspect your PPE once a month
  • to modify poor fitting PPE so it fits properly
  • to inspect your PPE prior to each use
  • to wear your PPE only when you sense an accident may happen

Pregunta 18

Pregunta
Industrial protective headwear must comply with what standard?
Respuesta
  • ULC
  • PPE
  • WCB
  • CSA

Pregunta 19

Pregunta
What is not an obligation your employer assumes when a hazard assessment indicates the need for PPE?
Respuesta
  • to post a Duty To Use Personal Protective Equipment sign at all entrances to the work site
  • to ensure employees are trained in the use, care, limitations and maintenance of their PPE
  • to ensure workers properly use and wear PPE
  • to ensure the PPE is in a condition to perform the function intended

Pregunta 20

Pregunta
What is a characteristic of protective footwear with a yellow triangle on the outer side or tongue of the right shoe?
Respuesta
  • sole puncture protection and Grade 2 protective toe (will withstand impact up to 90 Joules)
  • soles that provide electrical shock protection and a Grade 2 protective toe (will withstand impact up to 90 Joules)
  • sole puncture protection and Grade 1 protective toe (will withstand impact up to 125 Joules)
  • soles that provide electrical shock protection and a Grade 1 protective toe (will withstand impact up to 125 Joules)

Pregunta 21

Pregunta
In what situation is your employer obligated to provide you with proper PPE according the OHS Code?
Respuesta
  • when required PPE must be replaced more frequently that once a year
  • when required PPE must be replaced more frequently that once every 2 years
  • when workers are exposed to respiratory hazard or excessive noise levels
  • when workers are exposed to respiratory hazards only

Pregunta 22

Pregunta
Who is responsible for providing workers with WHMIS training?
Respuesta
  • The supplier of controlled products.
  • A training institute or provider.
  • The employee must obtain their own training.
  • The employer must provide the training.

Pregunta 23

Pregunta
Employers are responsible to:
Respuesta
  • provide a MSDS for each controlled product used in the workplace.
  • inform all workers about chemical hazards at the work site.
  • train workers about labels, MSDS and other identifiers.
  • all of the above.

Pregunta 24

Pregunta
Suppliers of controller products are responsible to:
Respuesta
  • train employees to safely dispose of hazardous products.
  • provide SDS for controlled product they sell or import.
  • provide extra labels for employees to use when transferring controlled products from the original container.
  • visit work sites to ensure controlled products are labelled properly.

Pregunta 25

Pregunta
Employees are responsible to:
Respuesta
  • classify controlled products.
  • train other employees about WHMIS.
  • apply workplace labels where and when required.
  • ensure SDS are readily available.

Pregunta 26

Pregunta
The key elements of WHMIS are:
Respuesta
  • employee education, SDS and product labelling.
  • Hazard Products Act, OHS and SDS.
  • employee labelling, SDS and employer training.
  • product labeling, OHS and Controlled Products Regulations.

Pregunta 27

Pregunta
The goal of WHMIS is to:
Respuesta
  • ensure workers have containers for controlled products.
  • ensure suppliers of controlled products provide training for all employees.
  • protect the worker by providing information on hazardous materials.
  • ensure that the requirements for information on hazardous materials are unique to the requirements of each province.

Pregunta 28

Pregunta
An SDS must be provided for each controlled product because they:
Respuesta
  • provide only the essential information from the label and are easier to read in an emergency.
  • contain the generic product names and are easier to locate and read than the labels on the containers.
  • are only for the employer's use when an emergency arises, and they can be retrieved from a secure location.
  • provide more detailed information than can be provided on a label.

Pregunta 29

Pregunta
The supplier label is attached to the:
Respuesta
  • container in which the product is shipped.
  • container in which the product is stored.
  • work site near where the product is used.
  • invoice when the product is delivered.

Pregunta 30

Pregunta
How do you identify a portable gasoline container that is approved for use? It:
Respuesta
  • is approved under the Alberta Occupational Health and Safety Code.
  • is approved by the Alberta Hazardous Materials Control Regulations.
  • has a MSDS label affixed to the outside of the container.
  • is approved by either one or both of the ULC or CSA.

Pregunta 31

Pregunta
Ventilation system requirements for the work site are found in the:
Respuesta
  • provincial and national building codes.
  • Alberta Occupational Health and Safety Code.
  • WCB Worker Handbook.
  • Alberta Construction Safety Association.

Pregunta 32

Pregunta
Before entering a confined workspace you should:
Respuesta
  • assemble all necessary tools and equipment to ensure easy access while working in the confined space.
  • contact your employer to obtain information on dangerous gases present in the confined workspace.
  • discuss your work plan with other workers who may have worked in a similar confined space.
  • use a gas detector to determine whether the area contains any dangerous fumes or gases.

Pregunta 33

Pregunta
What type of fire extinguisher is versatile in fighting different types of fires?
Respuesta
  • regular dry chemical
  • purple K dry chemical
  • multi-purpose dry chemical
  • dry powder

Pregunta 34

Pregunta
Fasteners used in explosive actuated tools are:
Respuesta
  • common nails with washers
  • manufactured from special steel and tempered
  • very hard and brittle

Pregunta 35

Pregunta
A drive pin is a fastener used to:
Respuesta
  • support wire for suspending a ceiling
  • permanently attach one material to another
  • attach one material to another with a nut

Pregunta 36

Pregunta
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener is blunted (meaning it can't fasten) the material is too:
Respuesta
  • soft
  • hard
  • brittle

Pregunta 37

Pregunta
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener penetrates easily, do not fasten because the material is too:
Respuesta
  • soft
  • hard
  • brittle

Pregunta 38

Pregunta
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If material cracks or shatters, do not fasten because the material is too:
Respuesta
  • soft
  • hard
  • brittle

Pregunta 39

Pregunta
A threaded knurled pin is designed for what material?
Respuesta
  • mild steel
  • concrete block
  • concrete
  • tempered steel

Pregunta 40

Pregunta
To be a qualified operator of an explosive actuated tool you must possess:
Respuesta
  • a valid driver's license from Alberta.
  • firearms training.
  • training in the use of each tool and familiarity with local safety regulations.
  • knowledge of the safety regulations.

Pregunta 41

Pregunta
OH&S states that operators of explosive actuated tools should always wear:
Respuesta
  • work gloves.
  • ear plugs.
  • hard hat.
  • eye protection.

Pregunta 42

Pregunta
If a tool is found to be defective, you should:
Respuesta
  • mark it defective and call a service representative.
  • try to fix it yourself.
  • sell it at a discount.
  • throw it away.

Pregunta 43

Pregunta
According to OH&S, what safety equipment is required when using an explosive actuated tool in a confined area such as a small room?
Respuesta
  • work gloves and hard hat
  • ear plugs and eye protection
  • hard hat and eye protection
  • eye protection and steel-toed boots

Pregunta 44

Pregunta
How much oil should be added to tool parts after cleaning?
Respuesta
  • one or two drops
  • several drops
  • apply liberally to a cloth and wipe all parts
  • none

Pregunta 45

Pregunta
What part requires replacement most often in a low velocity tool?
Respuesta
  • firing pin
  • trigger
  • buffer
  • piston

Pregunta 46

Pregunta
The width of the saw blade cut in the workpiece is called:
Respuesta
  • set.
  • blade pitch.
  • straight or wavy.
  • kerf.

Pregunta 47

Pregunta
The purpose of draw filing is to:
Respuesta
  • remove metal rapidly.
  • produce a smooth and flat surface.
  • finish rough surfaces.
  • remove sharp corners and burrs.

Pregunta 48

Pregunta
The removable serrated jaws on a bench vise are made from:
Respuesta
  • aluminum.
  • hardened steel.
  • cast steel.
  • cast iron.

Pregunta 49

Pregunta
A standard screwdriver blade maintains a better grip in the slot if the blade is ground slightly:
Respuesta
  • tapered.
  • concave.
  • convex.
  • rounded.

Pregunta 50

Pregunta
The included angle that should be ground on the point of a center punch is:
Respuesta
  • 30° to 60°
  • 90°
  • 120°
  • 150°

Pregunta 51

Pregunta
When tightening a bolt with a wrench:
Respuesta
  • an adjustable wrench gives the most precise fit on a hexagon headed bolt.
  • use a pipe on the end of the wrench to increase torque.
  • never push; always pull.
  • never pull; always push.

Pregunta 52

Pregunta
The reason for the crown on the end of a flat scraper is:
Respuesta
  • so that the outside edges do not dig into the finished workpiece.
  • to increase the area of the cutting edge.
  • to produce a sharp cutting edge.
  • to make it easier to scrape internal cylindrical surfaces.

Pregunta 53

Pregunta
Which is a purpose of a flat (cold) chisel?
Respuesta
  • cutting keys and grooves
  • cutting oil grooves
  • cutting off rivets
  • squaring up keyseat corners

Pregunta 54

Pregunta
What is a chisel made from?
Respuesta
  • aluminum
  • high carbon steel
  • low carbon steel
  • stainless steel

Pregunta 55

Pregunta
Alkaline cleaning must only be used on which of the following metals.
Respuesta
  • aluminum
  • zinc
  • lead
  • iron

Pregunta 56

Pregunta
Barrel finishing:
Respuesta
  • is a quick and inexpensive cleaning method.
  • is inexpensive and many parts can be completed at once.
  • uses high pressure air and steam.
  • uses petroleum-based products.

Pregunta 57

Pregunta
In the lapping process, which is charged?
Respuesta
  • the hardened roller
  • the hardened steel block
  • the lap
  • the workpiece

Pregunta 58

Pregunta
What is another name for Hand Pads and Rolls?
Respuesta
  • Scotch-Brite pads
  • scrub pads
  • SoS pads
  • sponge pad

Pregunta 59

Pregunta
The three hand taps found in a set are the:
Respuesta
  • starter, plug and bottoming
  • taper, plug and bottoming
  • taper, intermediate and finishing
  • starter, intermediate and chamfered.

Pregunta 60

Pregunta
What is the tap drill size for a 3/4-10 UNC 2B?
Respuesta
  • 3/4 inch
  • 21/32 inch
  • 37/64 inch
  • 11/16 inch

Pregunta 61

Pregunta
If a high-speed steel hand tap breaks in a hole, one way to remove it is:
Respuesta
  • with an electrical discharge machine.
  • by drilling it out with a high-speed steel drill bit.
  • by drilling a hole and using a stud extractor.
  • with a tap vibrator.

Pregunta 62

Pregunta
You have to choose between four steel rods to cut a 1/2-13 UNC 2A thread with an adjustable split die. Which diameter rod would you use?
Respuesta
  • 0.489
  • 0.497
  • 0.503
  • 0.515

Pregunta 63

Pregunta
Choose the correct tool to turn a die.
Respuesta
  • die wrench
  • die stock
  • die plate
  • die handle

Pregunta 64

Pregunta
The cutting action of a hand broach is performed by a series of successive teeth, each protruding:
Respuesta
  • 0.001 inch further than the preceding tooth.
  • 0.002 inch further than the preceding tooth.
  • 0.0003 inch further than the preceding tooth.
  • 0.003 inch further than the preceding tooth.

Pregunta 65

Pregunta
Hand reamers must be rotated:
Respuesta
  • counter-clockwise.
  • clockwise.
  • in reverse.
  • forward.

Pregunta 66

Pregunta
Pullers are used to:
Respuesta
  • move heavy equipment in a horizontal plane.
  • move heavy equipment in a vertical plane.
  • remove bearings, hubs and sprockets.
  • remove large heavy shafts.

Pregunta 67

Pregunta
Before working around a load that has been raised with a hydraulic jack:
Respuesta
  • the load must be blocked.
  • the jack handle must be removed.
  • the hydraulic fluid should be checked.
  • the jack should be seated on a flat surface.

Pregunta 68

Pregunta
Master precision levels should be picked up by the:
Respuesta
  • bottom surface.
  • vials.
  • top plate.
  • sides.

Pregunta 69

Pregunta
A mechanic's level has a sensitivity of:
Respuesta
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.
  • 0.005 inch per foot per division
  • 0.010 inch per foot per division.

Pregunta 70

Pregunta
Levelling feet are used on:
Respuesta
  • heavy equipment.
  • large machine tools.
  • small lightweight equipment.
  • vibrating equipment.

Pregunta 71

Pregunta
You can level machine tools with a carpenter's level.
Respuesta
  • True
  • False

Pregunta 72

Pregunta
Wind can affect both plumb bobs and vertical wires.
Respuesta
  • True
  • False

Pregunta 73

Pregunta
Which anchor bolt can you replace easily if you break it?
Respuesta
  • fixed
  • flexible
  • drop-in
  • boxed

Pregunta 74

Pregunta
Which anchor is designed to accommodate slight adjustment?
Respuesta
  • fixed
  • flexible
  • expansion bolt
  • drop-in

Pregunta 75

Pregunta
Which anchor is best suited for the edge of a concrete foundation?
Respuesta
  • expansion bolt
  • fixed
  • adhesive
  • drop-in

Pregunta 76

Pregunta
Reference lines are also known as:
Respuesta
  • working lines.
  • control lines.
  • datum lines.
  • all of the above.

Pregunta 77

Pregunta
A 12-inch master precision level requires 0.003 inch of shims under one end to bring it level when it is placed longitudinally on the bed of a machine tool eight feet long. What size shim should be placed under the end of the machine tool to level it?
Respuesta
  • 0.002 inch
  • 0.003 inch
  • 0.012 inch
  • 0.024 inch

Pregunta 78

Pregunta
Do not apply grout to a smooth concrete surface.
Respuesta
  • True
  • False

Pregunta 79

Pregunta
Homemade grout mixtures tend to shrink.
Respuesta
  • True
  • False

Pregunta 80

Pregunta
You can place polymeric grouts in colder temperatures than cement-based grouts.
Respuesta
  • True
  • False

Pregunta 81

Pregunta
Before grouting, you should torque anchor bolts:
Respuesta
  • to their final value.
  • to 50% of their final value.
  • to 25% of their final value.
  • not at all until the grout has cured.

Pregunta 82

Pregunta
Grout is so stiff that formwork is not required.
Respuesta
  • True
  • False

Pregunta 83

Pregunta
A master precision level has a sensitivity of:
Respuesta
  • 5 microns per foot per division.
  • 0.0001 inch per foot per division.
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.

Pregunta 84

Pregunta
When using wire sag charts to determine the levelness of a machine bed, deduct the sag from the measured vertical distance to give the true vertical distance.
Respuesta
  • True
  • False

Pregunta 85

Pregunta
Because reference lines are all very accurate, you can take important measurements from either side of any one of them.
Respuesta
  • True
  • False

Pregunta 86

Pregunta
Do not place cement-based grout mixtures below what temperature?
Respuesta
  • 5°C
  • 0°C
  • -5°C
  • -10°C

Pregunta 87

Pregunta
The kind of abrasive material used in grinding wheels for general purpose applications is:
Respuesta
  • silicon carbide.
  • boron carbide.
  • aluminum oxide.
  • diamond.

Pregunta 88

Pregunta
It is safe to carry a portable grinder by the power cord.
Respuesta
  • True
  • False

Pregunta 89

Pregunta
It is safe to use standard sockets with electric impact wrenches.
Respuesta
  • True
  • False

Pregunta 90

Pregunta
The larger the power drill, the slower the rpms and higher the torque.
Respuesta
  • True
  • False

Pregunta 91

Pregunta
Most cordless drills have torque control
Respuesta
  • True
  • False

Pregunta 92

Pregunta
Prolonged use of power or air tools can cause carpal tunnel syndrome.
Respuesta
  • True
  • False
Mostrar resumen completo Ocultar resumen completo

¿Quieres crear tus propios Tests gratis con GoConqr? Más información.

Similar

Tools
JonathanMacIntyre
Power Saws
Vincent Bergeron
Uirlisí Láimhe - Sábha
Cathal Ó Conghaile
Prepara la Selectividad
Diego Santos
CIUDADES I...
JL Cadenas
Ingeniería Industrial
monicasorelly14
Les Participes Passés.
ANTONIO JIMENEZ
Os determinantes en galego.
Isabel Mª Barcón Soto
flash cards vocabulario inglés
Michael Villalobos
Árbol genealógico de Zeus
marvyn.goicochea
Elementos de la COMUNICACIÓN
belladetormes
Explorar la Librería