Pregunta 1
Pregunta
When "Hydrogen Control" is specified for a manual metal arc welding project the electrode would normally be:
Respuesta
-
Cellulosic
-
Iron Oxide
-
Acid
-
Basic
Pregunta 2
Pregunta
When "Hydrogen Control" is specified for a manual metal arc welding project the electrode would normally be:
Respuesta
-
Cellulosic
-
Iron Oxide
-
Acid
-
Basic
Pregunta 3
Pregunta
You would certainly recognize a hydrogen controlled flux electrode from its:
Respuesta
-
Colour
-
Length
-
Trade Name
-
BS639/AWS Code Letter
Pregunta 4
Pregunta
You notice manual metal arc electrodes are being, stripped of flux, are being used as a filler metal wire for TIG welding. You would object because:
Pregunta 5
Pregunta
For open site manual metal welding the following equipment is available. Which would you choose for safe site working?
Respuesta
-
Single operator transformer
-
multi-operator transformer
-
AC/DC composition power unit
-
Diesel engine driven motor generator
Pregunta 6
Pregunta
In MMA welding what parameter is used for control of penetration into the base metal?
Pregunta 7
Pregunta
What type of characteristic is required for manual welding?
Respuesta
-
Constant voltage
-
flat characteristic
-
Drooping characteristic
-
DC generator
Pregunta 8
Pregunta
The weld metal deposit for MMA electrodes achieves its mechanical strength through:
Pregunta 9
Pregunta
What constituent is needed in the coating of an electrode to prevent the formation of porosity in the welding of a rimming steel?
Respuesta
-
Iron powders
-
Calcium florid
-
Silicon
-
calcium carbonate
Pregunta 10
Pregunta
Cellulose electrodes are often used when welding the root pass of pipes in the field because:
Respuesta
-
Hydrogen control is needed
-
There are iron powders in the electrode
-
Higher arc voltage can be obtained
-
Shorter arc length can be obtained
Pregunta 11
Pregunta
MMA electrodes can be grouped into three main types:
Respuesta
-
Basic, cellulose and rutile
-
Neutral, cellulose and rutile
-
None of the above
Pregunta 12
Pregunta
Movement of the arc in MMA welding by magnetic forces is called:
Respuesta
-
Arc deviation
-
Arc misalignment
-
Arc blow
-
Arc eye
Pregunta 13
Pregunta
Which of the following coatings is associated with welding?
Respuesta
-
Rutile
-
Cellulose
-
Basic
-
Oxodizing
-
A,B,C
Pregunta 14
Pregunta
The voltage necessary to maintain an arc during metal arc welding is termed:
Respuesta
-
Main supply voltage
-
arc current
-
Arc Voltage
-
Open circuit voltage
Pregunta 15
Pregunta
When MMA welding low carbon steel which electrode which electrode will give the greatest deposition rate?
Respuesta
-
Hydrogen controlled
-
cellulose
-
rutile
-
Iron powder
Pregunta 16
Pregunta
Hydrogen controlled electrodes were developed principally for:
Respuesta
-
The prevention of porosity
-
The prevention of cracking
-
The enhancement of arc voltage
-
There ease of arc starting
Pregunta 17
Pregunta
A basic electrode would normally:
Respuesta
-
Have superior mechanical properties
-
Require baking before use
-
Not to be used on low carbon steels
-
Both A and B
Pregunta 18
Pregunta
MMA welding of low alloy steels is more likely to be performed with:
Pregunta 19
Pregunta
When manual metal arc welding low carbon steel, which electrode covering will give the greatest degree of penetration?
Respuesta
-
Iron powder
-
Rutile
-
Cellulose
-
Low hydrogen
Pregunta 20
Pregunta
MMA welds made with damaged electrode coatings are subject to:
Respuesta
-
Porosity
-
Undercut
-
Excessive penetration
-
Excessive bead hieght