CCNA 3 Practice Quiz

Pregunta 1 de 63

1

Which technology is required when switched networks are designed to include redundant links?

Selecciona una de las siguientes respuestas posibles:

Spanning Tree Protocol
virtual LANs
link aggregation
virtual private networks

Explicación

Pregunta 2 de 63

1

Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?

Selecciona una de las siguientes respuestas posibles:

STP
Rapid PVST+
PVST+
MST

Explicación

Pregunta 3 de 63

1

Which statement describes a characteristic of Cisco Meraki switches?

Selecciona una de las siguientes respuestas posibles:

They are service provider switches that aggregate traffic at the edge of the network.
They are cloud-managed access switches that enable virtual stacking of switches.
They are campus LAN switches that perform the same functions as Cisco 2960 switches.
They promote infrastructure scalability, operational continuity, and transport flexibility.

Explicación

Pregunta 4 de 63

1

If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?

Selecciona una de las siguientes respuestas posibles:

highest IP address
lowest MAC address
lowest IP address
highest MAC address

Explicación

Pregunta 5 de 63

1

What is a characteristic of a Layer 2 loop?

Selecciona una de las siguientes respuestas posibles:

A switch is continually forwarding the same unicast frame.
Broadcast frames are forwarded back to the sending switch.
Routers continually forward packets to other routers.
The Time-to-Live attribute of a frame is set to infinity.

Explicación

Pregunta 6 de 63

1

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

redundant links between Layer 2 switches
removing single points of failure with multiple Layer 2 switches
link-state dynamic routing that provides redundant routes
static default routes
implementing VLANs to contain broadcasts

Explicación

Pregunta 7 de 63

1

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

listening
learning
forwarding
disabled
blocking

Explicación

Pregunta 8 de 63

1

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Selecciona una de las siguientes respuestas posibles:

root port
disabled port
alternate
designated port

Explicación

Pregunta 9 de 63

1

What is an advantage of using LACP?

Selecciona una de las siguientes respuestas posibles:

decreases the chance of a spanning-tree loop
provides a simulated environment for testing link aggregation
allows automatic formation of EtherChannel links
decreases the amount of configuration that is needed on a switch for EtherChannel
increases redundancy to Layer 3 devices

Explicación

Pregunta 10 de 63

1

Which command will initiate EtherChannel interface configuration mode?

Selecciona una de las siguientes respuestas posibles:

interface port-channel interface-identifier
interface interface-identifier
interface range interface-identifier
channel-group group-identifier

Explicación

Pregunta 11 de 63

1

Which PAgP mode combination will establish an EtherChannel?

Selecciona una de las siguientes respuestas posibles:

switch 1 set to desirable; switch 2 set to desirable.
switch 1 set to on; switch 2 set to desirable.
switch 1 set to auto; switch 2 set to auto.
switch 1 set to auto; switch 2 set to on.

Explicación

Pregunta 12 de 63

1

When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?

Selecciona una de las siguientes respuestas posibles:

active
desirable
auto
passive

Explicación

Pregunta 13 de 63

1

When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?

Selecciona una de las siguientes respuestas posibles:

desirable
auto
active
passive

Explicación

Pregunta 14 de 63

1

What type of wireless antenna is best suited for providing coverage in large open spaces, such as hallways or large conference rooms?

Selecciona una de las siguientes respuestas posibles:

Yagi
omnidirectional
directional
dish

Explicación

Pregunta 15 de 63

1

During which stage of establishing connectivity between a WLAN client and an AP does the client learn the MAC address of the AP?

Selecciona una de las siguientes respuestas posibles:

encryption
authentication
discovery
association
probing

Explicación

Pregunta 16 de 63

1

A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?

Selecciona una de las siguientes respuestas posibles:

Issue the clear ip ospf process privileged mode command.
Configure the network statements.
Change the OSPFv2 process ID.
Change the interface priority.

Explicación

Pregunta 17 de 63

1

Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

The DR can be reached through the GigabitEthernet 0/0 interface.
There have been 9 seconds since the last hello packet sent.
The router ID on the DR router is 3.3.3.3
The BDR has three neighbors.
The router ID values were not the criteria used to select the DR and the BDR.
This interface is using the default priority.

Explicación

Pregunta 18 de 63

1

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

Selecciona una de las siguientes respuestas posibles:

show ipv6 ospf interface serial 0/0/0
show ip ospf neighbor
show ip ospf interface serial 0/0/0
show ip ospf interface fastethernet 0/1

Explicación

Pregunta 19 de 63

1

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

Selecciona una de las siguientes respuestas posibles:

The R1 dead timer expires between hello packets from R2.
The neighbor adjacency has formed.
R1 automatically adjusts its own timers to match the R2 timers.
The hello timer on R2 expires every ten seconds.

Explicación

Pregunta 20 de 63

1

A network engineer is troubleshooting convergence and adjacency issues in an OSPFv2 network and has noted that some expected network route entries are not displayed in the routing table. Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

show running-configuration
show ip ospf neighbor
show ip ospf interface
show ip route ospf
show ip protocols

Explicación

Pregunta 21 de 63

1

A network engineer is troubleshooting an OSPFv2 network and discovers that two routers connected by a point-to-point WAN serial link are not establishing an adjacency. The OSPF routing process, network commands and area ID are all confirmed as correct, and the interfaces are not passive. Testing shows that the cabling is correct, that the link is up, and pings between the interfaces are successful. What is most likely the problem?

Selecciona una de las siguientes respuestas posibles:

A clock rate has not been set on the DCE interface of the serial link.
The OSPFv2 process IDs on each router do not match.
A DR election has not taken place.
The subnet masks on the two connected serial interfaces do not match.

Explicación

Pregunta 22 de 63

1

A network engineer is troubleshooting OSPFv2 routing issues on two connected routers. Which two requirements to form an adjacency need to be verified? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Verify that the interfaces that connect the two routers are in the same area.
Verify that one of the routers is the DR or BDR and the other router a DRother.
Verify that one of the interfaces that connects the two routers is active and the other passive.
Verify that the interfaces that connect the two routers are in the same subnet.
Verify that both routers are using the same OSPFv2 process ID.

Explicación

Pregunta 23 de 63

1

Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?

Selecciona una de las siguientes respuestas posibles:

show ip protocols
show ip ospf interface
show ip interface brief
show ip route ospf

Explicación

Pregunta 24 de 63

1

Refer to the exhibit. Four routers are connected to an Ethernet LAN segment and are configured to run OSPFv3. However, none of the routers are receiving routing updates. What is the cause of the problem?

Selecciona una de las siguientes respuestas posibles:

The routers are using IPv6 link local addresses to communicate.
The network type has been set to BROADCAST instead of NBMA.
The routers are using IPv4 addresses for router IDs.
All of the routers have an OSPFv3 interface priority of 0.

Explicación

Pregunta 25 de 63

1

Refer to the exhibit. These two routers are configured to run OSPFv3 but they are not forming a neighbor adjacency. What is the cause of the problem?

Selecciona una de las siguientes respuestas posibles:

The routers do not have global IPv6 addresses that are configured on the Fa0/0 interfaces.
The routers have both been elected as the DR.
The routers are configured with the same router ID.
The routers have the same priority.

Explicación

Pregunta 26 de 63

1

What is a recommended method of authentication for OSPFv3?

Selecciona una de las siguientes respuestas posibles:

MD5 authentication
IPsec to secure routing updates
the passive-interface command
a VPN tunnel between each OSPF neighbor adjacency

Explicación

Pregunta 27 de 63

1

During verification or troubleshooting of the OPSFv3 configuration on a router, which three parameters are displayed by the show ipv6 ospf interface command? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

the hello and dead intervals
the metric of the route that is attached to the interface
the global unicast IPv6 address of the interface
the number of interfaces in the area
the OSPFv3 area that the interface is in
the process ID that is assigned to the interface

Explicación

Pregunta 28 de 63

1

Refer to the exhibit. What can be concluded about network 192.168.4.0 in the R2 routing table?

Selecciona una de las siguientes respuestas posibles:

This network should be used to forward traffic toward external networks.
The network was learned from a router within the same area as R2.
The network was learned through summary LSAs from an ABR.
The network can be reached through the GigabitEthernet0/0 interface.

Explicación

Pregunta 29 de 63

1

Refer to the exhibit. What is indicated by the O IA in the router output?

Selecciona una de las siguientes respuestas posibles:

The route was learned from within the area.
The route was learned from outside the internetwork.
The route was manually configured.
The route was learned from another area.

Explicación

Pregunta 30 de 63

1

Which statement describes a multiarea OSPF network?

Selecciona una de las siguientes respuestas posibles:

It has a core backbone area with other areas connected to the backbone area.
It has multiple routers that run multiple routing protocols simultaneously, and each protocol consists of an area.
It consists of multiple network areas that are daisy-chained together.
It requires a three-layer hierarchical network design approach.

Explicación

Pregunta 31 de 63

1

A network administrator is implementing OSPF in a portion of the network and must ensure that only specific routes are advertised via OSPF. Which network statement would configure the OSPF process for networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now located in the backbone area, and inject them into the OSPF domain?

Selecciona una de las siguientes respuestas posibles:

r1(config-router)# network 192.168.0.0 0.0.0.255 area 1
r1(config-router)# network 192.168.4.0 0.0.255.255 area 0
r1(config-router)# network 192.168.4.0 0.0.15.255 area 1
r1(config-router)# network 192.168.0.0 0.0.3.255 area 0
r1(config-router)# network 192.168.4.0 0.0.3.255 area 0
r1(config-router)# network 192.168.4.0 0.0.3.255 area 1

Explicación

Pregunta 32 de 63

1

Which two networks are part of the summary route 192.168.32.0/22? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

192.168.35.0/24
192.168.36.0/24
192.168.33.0/24
192.168.31.0/24
192.168.37.0/24
192.168.38.0/24

Explicación

Pregunta 33 de 63

1

What routing table descriptor is used to identify OSPF summary networks that originate from an ABR?

Selecciona una de las siguientes respuestas posibles:

O E1
O E2
O
O IA

Explicación

Pregunta 34 de 63

1

A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

bandwidth
MTU
delay
load
reliability

Explicación

Pregunta 35 de 63

1

If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?

Selecciona una de las siguientes respuestas posibles:

10 seconds
15 seconds
20 seconds
30 seconds

Explicación

Pregunta 36 de 63

1

Which EIGRP route would have the preferred administrative distance?

Selecciona una de las siguientes respuestas posibles:

a summary route
an internal route
an external route that is redistributed from RIP
an external route that is redistributed from OSPF

Explicación

Pregunta 37 de 63

1

When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?

Selecciona una de las siguientes respuestas posibles:

EIGRP authentication
Diffusing Update Algorithm
Reliable Transport Protocol
bounded updates
partial updates

Explicación

Pregunta 38 de 63

1

Where are EIGRP successor routes stored?

Selecciona una de las siguientes respuestas posibles:

only in the routing table
in the routing table and the topology table
only in the neighbor table
in the routing table and the neighbor table

Explicación

Pregunta 39 de 63

1

Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?

Selecciona una de las siguientes respuestas posibles:

show ip protocols
show interfaces
show ip interface brief
show ip route

Explicación

Pregunta 40 de 63

1

What information does EIGRP maintain within the routing table?

Selecciona una de las siguientes respuestas posibles:

only feasible successors
adjacent neighbors
only successors
all routes known to the router
both successors and feasible successors

Explicación

Pregunta 41 de 63

1

Which command can be issued on a router to verify that automatic summarization is enabled?

Selecciona una de las siguientes respuestas posibles:

show ip eigrp neighbors
show ip protocols
show ip interface brief
show ip eigrp interfaces

Explicación

Pregunta 42 de 63

1

Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?

Selecciona una de las siguientes respuestas posibles:

Automatic summarization has been enabled only for the 172.21.100.0/24 network.
Automatic summarization is enabled on neighboring routers.
Automatic summarization is disabled on a per-interface basis.
Automatic summarization is disabled on R3.

Explicación

Pregunta 43 de 63

1

Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?

Selecciona una de las siguientes respuestas posibles:

because the automatic summarization is enabled on R1
because the IPv4 address on Fa0/0 interface of R1 is incorrect
because the Fa0/0 interface of R1 is declared as passive for EIGRP
because there is no network command for the network 192.168.1.0/24 on R1

Explicación

Pregunta 44 de 63

1

In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?

Selecciona una de las siguientes respuestas posibles:

router configuration mode
interface configuration mode
global configuration mode
privileged mode

Explicación

Pregunta 45 de 63

1

Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be causing this problem?

Selecciona una de las siguientes respuestas posibles:

a process ID mismatch
an authentication mismatch
an access list that is blocking advertisements from other networks
automatic summarization that is disabled on both routers

Explicación

Pregunta 46 de 63

1

Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?

Selecciona una de las siguientes respuestas posibles:

The GigabitEthernet 0/1 interface is not participating in the EIGRP process.
The hello timer has been modified on interface GigabitEthernet 0/1 of R3 and not on the neighbor, causing a neighbor adjacency not to form.
The passive-interface command is preventing neighbor relationships on interface GigabitEthernet 0/0.
The GigabitEthernet interfaces are not limiting the flow of EIGRP message information and are being flooded with EIGRP traffic.

Explicación

Pregunta 47 de 63

1

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.

What action should be taken to solve this problem?

Selecciona una de las siguientes respuestas posibles:

Configure the same hello interval between the routers.
Configure EIGRP to send periodic updates.
Enable the serial interfaces of both routers.
Configure both routers with the same EIGRP process ID.

Explicación

Pregunta 48 de 63

1

Refer to the exhibit. Which statement is supported by the output?

Selecciona una de las siguientes respuestas posibles:

The route to 192.168.1.1 represents the configuration of a loopback interface.
A static default route has been manually configured on this router.
A default route is being learned through an external process.
Summarization of routes has been manually configured.

Explicación

Pregunta 49 de 63

1

Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?

Selecciona una de las siguientes respuestas posibles:

The same autonomous system numbers must be used in the interface configurations of each router.
The key string should be used in interface mode instead of the key chain.
The same number of key strings must be used on each router.
The same key chain name must be used on each router.
The authentication configuration is correct, issue the show ip eigrp neighbors command to troubleshoot the issue.

Explicación

Pregunta 50 de 63

1

Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?

Selecciona una de las siguientes respuestas posibles:

ip bandwidth-percent eigrp 100 48
ip bandwidth-percent eigrp 100 75
ip bandwidth-percent eigrp 75 100
ip bandwidth-percent eigrp 64 48
ip bandwidth-percent eigrp 100 64

Explicación

Pregunta 51 de 63

1

Which three statements are advantages of using automatic summarization? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

It decreases the number of entries in the routing table.
It reduces the frequency of routing updates.
It ensures that traffic for multiple subnets uses one path through the internetwork.
It maximizes the number of routes in the routing table.
It improves reachability in discontiguous networks.
It increases the size of routing updates.

Explicación

Pregunta 52 de 63

1

Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?

Selecciona una de las siguientes respuestas posibles:

The passive-interface command should have been issued on serial 0/1/0.
The IPv4 address configured on the neighbor that is connected to R1 serial 0/1/0 is incorrect.
The hello interval has been altered on serial 0/1/0 and is preventing a neighbor relationship from forming.
The network statement used for EIGRP 55 does not enable EIGRP on interface serial 0/1/0.
The networks that are configured on serial 0/0/0 and serial 0/1/0 of router R1 are overlapping.

Explicación

Pregunta 53 de 63

1

What is a characteristic of manual route summarization?

Selecciona una de las siguientes respuestas posibles:

requires high bandwidth utilization for the routing updates
has to be configured globally on the router
reduces total number of routes in routing tables
cannot include supernet routes

Explicación

Pregunta 54 de 63

1

Refer to the exhibit. A network administrator has issued the shown commands. The EIGRP routing domain has completely converged and a network administrator is planning on configuring EIGRP authentication throughout the complete network. On which two interfaces should EIGRP authentication be configured between R2 and R3? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

gig 0/0 of R3
serial 0/1/0 of R4
serial 0/1/0 of R2
serial 0/0/1 of R2
serial 0/0/1 of R3

Explicación

Pregunta 55 de 63

1

Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

172.16.3.0/24
172.16.0.0/16
192.168.10.0/24
192.168.10.0/30
192.168.1.0/30

Explicación

Pregunta 56 de 63

1

Refer to the exhibit. Router CiscoVille has been partially configured for EIGRP authentication. What is missing that would allow successful authentication between EIGRP neighbors?

Selecciona una de las siguientes respuestas posibles:

The CiscoVille router requires a second keychain to function correctly when using two interfaces for EIGRP authentication.
The keychain for EIGRP authentication must be configured on the interfaces.
A username and password must be configured.
The interfaces that will use EIGRP authentication must be specified.

Explicación

Pregunta 57 de 63

1

Beginning with the Cisco IOS Software Release 15.0, which license is a prerequisite for installing additional technology pack licenses?

Selecciona una de las siguientes respuestas posibles:

UC
IPBase
SEC
DATA

Explicación

Pregunta 58 de 63

1

What statement describes a Cisco IOS image with the “universalk9_npe” designation for Cisco ISR G2 routers?

Selecciona una de las siguientes respuestas posibles:

It is an IOS version that, at the request of some countries, removes any strong cryptographic functionality.
It is an IOS version that provides only the IPBase feature set.
It is an IOS version that offers all of the Cisco IOS Software feature sets.
It is an IOS version that can only be used in the United States of America.

Explicación

Pregunta 59 de 63

1

Which command is used to configure a one-time acceptance of the EULA for all Cisco IOS software packages and features?

Selecciona una de las siguientes respuestas posibles:

license save
license accept end user agreement
show license
license boot module module-name

Explicación

Pregunta 60 de 63

1

How long is the evaluation license period for Cisco IOS Release 15.0 software packages?

Selecciona una de las siguientes respuestas posibles:

30 days
15 days
60 days
180 days

Explicación

Pregunta 61 de 63

1

Which IOS 12.4 software package integrates full features, including voice, security, and VPN capabilities, for all routing protocols?

Selecciona una de las siguientes respuestas posibles:

Service Provider Services
Advanced Enterprise Services
Advanced Security
Advanced IP Services

Explicación

Pregunta 62 de 63

1

When a customer purchases a Cisco IOS 15.0 software package, what serves as the receipt for that customer and is used to obtain the license as well?

Selecciona una de las siguientes respuestas posibles:

Product Activation Key
Unique Device Identifier
Software Claim Certificate
End User License Agreement

Explicación

Pregunta 63 de 63

1

The customer of a networking company requires VPN connectivity for workers who must travel frequently. To support the VPN server, the customer router must be upgraded to a new Cisco IOS software version with the Advanced IP Services feature set. What should the field engineer do before copying the new IOS to the router?

Selecciona una de las siguientes respuestas posibles:

Issue the show version and the show flash commands to ensure that the router has enough memory and file space to support the new IOS image.
Set the router to load the new IOS image file directly from the TFTP server on the next reboot.
Delete the currently installed IOS by using the erase flash: command, and reload the router
Issue the show running-configuration command to determine the features of the currently installed IOS image file.

	Creado por th1rt33n_tony hace alrededor de 9 años

CCNA Practice Quiz

CCNA 3 Practice Quiz

CCNA 3 Practice Quiz

Pregunta 1 de 63

Which technology is required when switched networks are designed to include redundant links?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 2 de 63

Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 3 de 63

Which statement describes a characteristic of Cisco Meraki switches?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 4 de 63

If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 5 de 63

What is a characteristic of a Layer 2 loop?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 6 de 63

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 7 de 63

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 8 de 63

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 9 de 63

What is an advantage of using LACP?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 10 de 63

Which command will initiate EtherChannel interface configuration mode?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 11 de 63

Which PAgP mode combination will establish an EtherChannel?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 12 de 63

When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 13 de 63

When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 14 de 63

What type of wireless antenna is best suited for providing coverage in large open spaces, such as hallways or large conference rooms?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 15 de 63

During which stage of establishing connectivity between a WLAN client and an AP does the client learn the MAC address of the AP?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 16 de 63

A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 17 de 63

Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 18 de 63

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 19 de 63

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 20 de 63