Wet abrading is carried out on which type of ground coating?
a Acrylic borne eggshell.
b Oil borne eggshell.
c Powdered filler.
d Flexible filler.
What is the most suitable acrylic borne coating to use as a ground coat when applying a water borne system?
a Gloss.
b Eggshell.
c Emulsion.
d Undercoat.
Which of the following can cause bittiness to decorative work?
a Uneven colour.
b Uneven application.
c Insufficient material.
d Insufficient preparation.
What is the correct way to lay off a solvent borne eggshell ground coat on a wall?
a Crisscross.
b Vertically.
c Arching.
d Horizontally.
What is the main benefit of using a stipple brush on ground coats?
a It makes the application faster.
b It reduces the drying time.
c It removes brush marks.
d It deepens the colour
What material is mixed with a glaze to produce a scumble?
a Oil.
b Spirit.
c Water.
d Colourant
What tool is used to create a soft appearance on a glazed surface?
a Natural sponge.
b Mohair roller.
c Stipple brush.
d Chamois leather.
Other than boots and overalls, which PPE should be worn when applying broken colour effect?
a Mask.
b Gloves.
c Goggles.
d Ear plugs.
Which of the following describes a glaze?
a A material used to extend the drying time in paint.
b One of the additives that make up a scumble.
c A material used to make up a stencil.
d An additive that makes up a primer.
Which material is used to extend the drying time in oil borne scumble?
a White spirit.
b Linseed oil.
c Colourant.
d Glaze.
What will cause yellowing to broken colour after a period of time?
a Lack of light.
b Lack of spirit.
c Lack of scumble.
d Lack of colourant
Why should more scumble than needed be mixed together for a piece of work?
a To save time.
b To repair damage.
c To allow for spillages.
d To prepare for the next job
Adding thinners to the scumble will alter the effect by
a adding shine
b darkening
c yellowing
d lightening.
Which of the following describes a substrate that allows light to pass through but cannot be seen through?
a Translucent.
b Reflective.
c Transparent.
d Opaque.
When rag rolling what application fault is caused by not overlapping the pattern?
a Creeping.
b Skidding.
c Bleeding.
d Banding
How can skidding be prevented?
a Keeping a wet edge going.
b Crossing over when ragging.
c Using the correct ground coat.
d Mixing the correct ratio of materials
What would happen if incorrect tape is used when masking?
a Uneven edges.
b Crisp edges.
d Creepage.
Damage to surface when removing masking tape is mainly caused by
a incorrect tape choice
b pulling the tape off slowly
c reducing the tackiness of the tape
d pulling the tape towards the surface.
What is the correct process when cleaning chamois leathers?
a Wash, fold, store.
b Dry, fold, store.
c Wash, dry, store.
d Hang, dry, store.
How should brushes be stored after cleaning to allow for drying?
a Hung in ventilated area.
b Hung up in a cupboard.
c Laid on a bench.
d Laid in a box.
What type of stencil is cut out and paint applied over the opening shown in the image?
a Positive.
b Multi.
c Plate.
d Negative
When carrying out stencil work in a room the focal point is most likely to be a
a chimney breast
b wall with a door
c window wall
d corner.
What is the main purpose of registration marks?
a To find the centre.
b To keep the stencil level.
c To identify the starting point.
d To identify the finishing point
Why should low tack tape be used to secure stencil plates?
a To prevent buckling.
b To prevent creeping.
c To prevent uneven colour.
d To prevent surface damage.
Por favor espera - en proceso…