Neil Revollo
Test por , creado hace más de 1 año

Control Strategies, Components, and Systems

364
0
0
Neil Revollo
Creado por Neil Revollo hace alrededor de 8 años
Cerrar

Chapter 9 - Quiz

Pregunta 1 de 20

1

For current-generation hydronic heating systems, the controlled variable is usually indoor air temperature.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 2 de 20

1

Most of the closed-loop control systems used for hydronic heating continually seek to eliminate any error that exists between the target value and measured value of the controlled variable.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 3 de 20

1

Heat output from the heat emitter occurs whenever the supply water temperature equals the room air temperature.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 4 de 20

1

The combination of near-continuous circulation and very gradual changes in water temperature tends to maximize expansion noises from the distribution piping and heat emitters.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 5 de 20

1

Most heat source reset controllers have an adjustable minimum supply temperature.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 6 de 20

1

Relay contacts are designated as normally open, or normally closed. In this context, the word "normally" means when the coil of the relay is not energized.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 7 de 20

1

There are hydronic heating applications where control action is required based on the difference between two temperatures rather than the value of either temperature.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 8 de 20

1

A multizone relay center is designed to isolate the wiring and control operation of several independent zone circulators or zone valves.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 9 de 20

1

One purpose of mixing is to protect conventional boilers from operating at conditions that allow sustained flue gas condensation.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 10 de 20

1

Direct injection mixing, whether accomplished using a two-way valve or variable-speed pump as the injection control device, provides the highest temperature difference between the supply and return injection risers.

Selecciona uno de los siguientes:

  • VERDADERO
  • FALSO

Explicación

Pregunta 11 de 20

1

The proper documentation of control systems is essential if they are to be expediently serviced in the future. A universally accepted tool for such documentation is the __________.

Selecciona una de las siguientes respuestas posibles:

  • microprocessor

  • ladder diagram

  • designer spreadsheet

  • flow chart

Explicación

Pregunta 12 de 20

1

The term __________ differential refers to the actual variation in the controlled variable as the system operates.

Selecciona una de las siguientes respuestas posibles:

  • control

  • modulating

  • operating

  • real-time

Explicación

Pregunta 13 de 20

1

To provide accurate control under low-load conditions, the controlled device must be able to maintain stable flow at very low flow rates. Such a device is said to have good __________.

Selecciona una de las siguientes respuestas posibles:

  • modulation

  • variability

  • machining

  • rangeability

Explicación

Pregunta 14 de 20

1

As outdoor temperature increases, and the heating load decreases, the water temperature supplied to the heat emitters also decreases as does their heat output. This concept is called outdoor __________ control.

Selecciona una de las siguientes respuestas posibles:

  • temperature

  • variable

  • proportional

  • reset

Explicación

Pregunta 15 de 20

1

Switches and relays are classified according to their poles and throws. The number of __________ is the number of independent and simultaneous electrical paths through the switch.

Selecciona una de las siguientes respuestas posibles:

  • poles

  • throws

  • contacts

  • wires

Explicación

Pregunta 16 de 20

1

__________ control is a planned strategy for shedding (e.g., temporarily turning off) one or more loads when a specific condition is detected in the system.

Selecciona una de las siguientes respuestas posibles:

  • Error

  • Priority

  • Systemic

  • Conditional

Explicación

Pregunta 17 de 20

1

In addition to equal run time rotation, there are other operating options available for staged/modulating heat sources. They are called series staging/modulation, parallel staging/modulation, and __________ staging/modulation.

Selecciona una de las siguientes respuestas posibles:

  • proportional

  • on/off

  • multiple

  • hybrid

Explicación

Pregunta 18 de 20

1

Boiler protection is accomplished by __________ the rate of heat flow from the boiler into the distribution system whenever the boiler temperature approaches or falls below a specified minimum operating temperature.

Selecciona una de las siguientes respuestas posibles:

  • reducing

  • resetting

  • increasing

  • stabilizing

Explicación

Pregunta 19 de 20

1

The term injection mixing applies to any mixing assembly in which __________ is pushed (e.g., injected) into a circulating distribution system.

Selecciona una de las siguientes respuestas posibles:

  • coolant

  • air

  • hot water

  • mercury

Explicación

Pregunta 20 de 20

1

A network control system without Internet access requires a person to be present to interrogate or adjust the system. This is unnecessary with a(n) __________ networked control system.

Selecciona una de las siguientes respuestas posibles:

  • Web-enabled

  • electronic

  • electromechanical

  • fuzzy logic

Explicación

Anterior
Siguiente