CCNA 3V5.03 Final B

Por favor espera - en proceso…

Pregunta 1 de 110

A network designer is considering whether to implement a switch block on the company network. What is the primary advantage of deploying a switch block?

Selecciona una de las siguientes respuestas posibles:

A single core router provides all the routing between VLANs.
This is network application software that prevents the failure of a single network device.
The failure of a switch block will not impact all end users.
This is a security feature that is available on all new Catalyst switches.

Explicación

Pregunta 2 de 110

Refer to the exhibit. A network administrator is attempting to upgrade the IOS system image on a Cisco 2901 router. After the new image has been downloaded and copied to the TFTP server, what command should be issued on the router before the IOS system image is upgraded on the router?

Selecciona una de las siguientes respuestas posibles:

ping 10.10.10.1
dir flash:
ping 10.10.10.2
copy tftp: flash0:

Explicación

Pregunta 3 de 110

Rellena el espacio en blanco para completar el texto.

The area interconnects with all other OSPF area types.

Explicación

Pregunta 4 de 110

In a large enterprise network, which two functions are performed by routers at the distribution layer? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

provide Power over Ethernet to devices
provide a high-speed network backbone
connect remote networks
connect users to the network
provide data traffic security

Explicación

Pregunta 5 de 110

Which address is used by an IPv6 EIGRP router as the source for hello messages?

Selecciona una de las siguientes respuestas posibles:

the interface IPv6 link-local address
the 32-bit router ID
the all-EIGRP-routers multicast address
the IPv6 global unicast address that is configured on the interface

Explicación

Pregunta 6 de 110

Refer to the exhibit. Which switch will be the root bridge after the election process is complete?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 7 de 110

Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network?

Selecciona una de las siguientes respuestas posibles:

alternate, root, designated, root
designated, root, alternate, root
alternate, designated, root, root
designated, alternate, root, root

Explicación

Pregunta 8 de 110

Refer to the exhibit. A network administrator issues the show ipv6 eigrp neighbors command. Which conclusion can be drawn based on the output?

Selecciona una de las siguientes respuestas posibles:

The link-local addresses of neighbor routers interfaces are configured manually.
If R1 does not receive a hello packet from the neighbor with the link-local address FE80::5 in 2 seconds, it will declare the neighbor router is down.
R1 has two neighbors. They connect to R1 through their S0/0/0 and S0/0/1 interfaces.
The neighbor with the link-local address FE80::5 is the first EIGRP neighbor that is learned by R1.

Explicación

Pregunta 9 de 110

Which characteristic would most influence a network design engineer to select a multilayer switch over a Layer 2 switch?

Selecciona una de las siguientes respuestas posibles:

ability to have multiple forwarding paths through the switched network based on VLAN number(s)
ability to aggregate multiple ports for maximum data throughput
ability to build a routing table
ability to provide power to directly-attached devices and the switch itself

Explicación

Pregunta 10 de 110

Refer to the exhibit. Which two conclusions can be derived from the output? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

The network 192.168.10.8/30 can be reached through 192.168.11.1.
The reported distance to network 192.168.1.0/24 is 41024256.
Router R1 has two successors to the 172.16.3.0/24 network.
There is one feasible successor to network 192.168.1.8/30.
The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network.

Explicación

Pregunta 11 de 110

What two conditions have to be met in order to form a cluster that includes 5 access points? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

The APs must use different cluster names.
The APs must all be configured to use different radio modes.
At least two controllers are needed to form the cluster.
The APs have to be connected on the same network segment.
Clustering mode must be enabled on the APs.

Explicación

Pregunta 12 de 110

Which technological factor determines the impact of a failure domain?

Selecciona una de las siguientes respuestas posibles:

the forwarding rate of the switches used on the access layer
the number of layers of the hierarchical network
the role of the malfunctioning device
the number of users on the access layer

Explicación

Pregunta 13 de 110

Which mode configuration setting would allow formation of an EtherChannel link between switches SW1 and SW2 without sending negotiation traffic?

Selecciona una de las siguientes respuestas posibles:

SW1: desirable
SW2: desirable
SW1: passive
SW2: active
SW1: on
SW2: on
SW1: auto
SW2: auto
trunking enabled on both switches
SW1: auto
SW2: auto
PortFast enabled on both switches

Explicación

Pregunta 14 de 110

A network engineer is implementing security on all company routers. Which two commands must be issued to force authentication via the password 1C34dE for all OSPF-enabled interfaces in the backbone area of the company network? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

area 0 authentication message-digest
ip ospf message-digest-key 1 md5 1C34dE
username OSPF password 1C34dE
enable password 1C34dE
area 1 authentication message-digest

Explicación

Pregunta 15 de 110

When does an OSPF router become an ABR?

Selecciona una de las siguientes respuestas posibles:

when the router is configured as an ABR by the network administrator
when the router has interfaces in different areas
when the router has an OSPF priority of 0
when the router has the highest router ID

Explicación

Pregunta 16 de 110

A network administrator enters the spanning-tree portfast bpduguard default command. What is the result of this command being issued on a Cisco switch?

Selecciona una de las siguientes respuestas posibles:

Any switch port will be error-disabled if it receives a BPDU.
Any switch port that has been configured with PortFast will be error-disabled if it receives a BPDU.
Any trunk ports will be allowed to connect to the network immediately, rather than waiting to converge.
Any switch port that receives a BPDU will ignore the BPDU message.

Explicación

Pregunta 17 de 110

Refer to the exhibit. What are two results of issuing the displayed commands on S1, S2, and S3? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

S3 can be elected as a secondary bridge.
S2 can become root bridge if S3 fails.
S1 will automatically adjust the priority to be the lowest.
S2 can become root bridge if S1 fails.
S1 will automatically adjust the priority to be the highest.

Explicación

Pregunta 18 de 110

A remote classroom can successfully access video-intensive streaming lectures via wired computers. However, when an 802.11n wireless access point is installed and used with 25 wireless laptops to access the same lectures, poor audio and video quality is experienced. Which wireless solution would improve the performance for the laptops?

Selecciona una de las siguientes respuestas posibles:

Upgrade the access point to one that can route.
Decrease the power of the wireless transmitter.
Adjust the wireless NICs in the laptops to operate at 10GHz to be compatible with 802.11n.
Add another access point.

Explicación

Pregunta 19 de 110

A network engineer is troubleshooting a single-area OSPFv3 implementation across routers R1, R2, and R3. During the verification of the implementation, it is noted that the routing tables on R1 and R2 do not include the entry for a remote LAN on R3. Examination of R3 shows the following:

that all interfaces have correct addressing
that the routing process has been globally configured
that correct router adjacencies have formed
What additional action taken on R3 could solve the problem?

Selecciona una de las siguientes respuestas posibles:

Force DR/BDR elections to occur where required.
Use the network command to configure the LAN network under the global routing process.
Enable the OSPFv3 routing process on the interface connected to the remote LAN.
Restart the OPSFv3 routing process.

Explicación

Pregunta 20 de 110

When should EIGRP automatic summarization be turned off?

Selecciona una de las siguientes respuestas posibles:

when a network addressing scheme uses VLSM
when a router has more than three active interfaces
when a network contains discontiguous network addresses
when a router has less than five active interfaces
when a router has not discovered a neighbor within three minutes

Explicación

Pregunta 21 de 110

When will a router that is running EIGRP put a destination network in the active state?

Selecciona una de las siguientes respuestas posibles:

when the EIGRP domain is converged
when there is outgoing traffic toward the destination network
when the connection to the successor of the destination network fails and there is no feasible successor available
when there is an EIGRP message from the successor of the destination network

Explicación

Pregunta 22 de 110

Which action should be taken when planning for redundancy on a hierarchical network design?

Selecciona una de las siguientes respuestas posibles:

add alternate physical paths for data to traverse the network
continually purchase backup equipment for the network
immediately replace a non-functioning module, service or device on a network
implement STP portfast between the switches on the network

Explicación

Pregunta 23 de 110

Rellena el espacio en blanco para completar el texto.

Which encryption protocol is used by the WPA2 shared key authentication technique?

Explicación

Pregunta 24 de 110

Refer to the exhibit. When the show ip ospf neighbor command is given from the R1# prompt, no output is shown. However, when the show ip interface brief command is given, all interfaces are showing up and up. What is the most likely problem?

Selecciona una de las siguientes respuestas posibles:

R1 has not sent a default route down to R2 by using the default-information originate command.
R2 has not brought the S0/0/1 interface up yet.
R1 or R2 does not have a network statement for the 172.16.100.0 network.
The ISP has not configured a static route for the ABC Company yet.
R1 or R2 does not have a loopback interface that is configured yet.

Explicación

Pregunta 25 de 110

Refer to the exhibit. If router B is to be configured for EIGRP AS 100, which configuration must be entered?

Selecciona una de las siguientes respuestas posibles:

B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3
B(config-router)# network 192.168.10.64 0.0.0.63
B(config-router)# network 192.168.10.128 0.0.0.63
B(config-router)# network 192.168.10.192 0.0.0.63
B(config-router)# network 192.168.10.4 255.255.255.248
B(config-router)# network 192.168.10.8 255.255.255.248
B(config-router)#network 192.168.10.128 255.255.255.192
B(config-router)# network 192.168.10.0 255.255.255.0
B(config-router)# network 192.168.10.0 0.0.0.255
B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3
B(config-router)#network 192.168.10.128 0.0.0.63
B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3

Explicación

Pregunta 26 de 110

Refer to the exhibit. A network technician is troubleshooting missing OSPFv3 routes on a router. What is the cause of the problem based on the command output?

Selecciona una de las siguientes respuestas posibles:

The local router has formed complete neighbor adjacencies, but must be in a 2WAY state for the router databases to be fully synchronized.
The neighbor IDs are incorrect. The interfaces must use only IPv6 addresses to ensure fully synchronized routing databases.
The dead time must be higher than 30 for all routers to form neighbor adjacencies.
There is a problem with the OSPFv3 adjacency between the local router and the router that is using the neighbor ID 2.2.2.2.

Explicación

Pregunta 27 de 110

Refer to the exhibit. Which two conclusions can be drawn from the output? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

The bundle is fully operational.
The port channel is a Layer 3 channel.
The EtherChannel is down
The port channel ID is 2.
The load-balancing method used is source port to destination port.

Explicación

Pregunta 28 de 110

Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel?

Selecciona una de las siguientes respuestas posibles:

The EtherChannel is dynamic and is using ports Fa0/10 and Fa0/11 as passive ports.
The EtherChannel is in use and functional as indicated by the SU and P flags in the command output.
The EtherChannel is down as evidenced by the protocol field being empty.
The EtherChannel is partially functional as indicated by the P flags for the FastEthernet ports.

Explicación

Pregunta 29 de 110

A network engineer is configuring a LAN with a redundant first hop to make better use of the available network resources. Which protocol should the engineer implement?

Selecciona una de las siguientes respuestas posibles:

FHRP
VRRP
GLBP
HSRP

Explicación

Pregunta 30 de 110

Users on an IEEE 801.11n network are complaining of slow speeds. The network administrator checks the AP and verifies it is operating properly. What can be done to improve the wireless performance in the network?

Selecciona una de las siguientes respuestas posibles:

Split the wireless traffic between the 802.11n 2.4 GHz band and the 5 GHz band.
Set the AP to mixed mode.
Change the authentication method on the AP.
Switch to an 802.11g AP.

Explicación

Pregunta 31 de 110

A network administrator is troubleshooting slow performance in a Layer 2 switched network. Upon examining the IP header, the administrator notices that the TTL value is not decreasing. Why is the TTL value not decreasing?

Selecciona una de las siguientes respuestas posibles:

This is the normal behavior for a Layer 2 network.
The VLAN database is corrupt.
The MAC address table is full.
The inbound interface is set for half duplex.

Explicación

Pregunta 32 de 110

What is a wireless modulation technique used by 802.11 WLAN standards that can implement MIMO?

Selecciona una de las siguientes respuestas posibles:

FHSS
OFDM
BSS
DSSS

Explicación

Pregunta 33 de 110

Which technology is an open protocol standard that allows switches to automatically bundle physical ports into a single logical link?

Selecciona una de las siguientes respuestas posibles:

Multilink PPP
PAgP
DTP
LACP

Explicación

Pregunta 34 de 110

A set of switches is being connected in a LAN topology. Which STP bridge priority value will make it least likely for the switch to be selected as the root?

Selecciona una de las siguientes respuestas posibles:

32768
4096
65535
61440

Explicación

Pregunta 35 de 110

Which wireless network topology is being configured by a technician who is installing a keyboard, a mouse, and headphones, each of which uses Bluetooth?

Selecciona una de las siguientes respuestas posibles:

ad hoc mode
hotspot
mixed mode
infrastructure mode

Explicación

Pregunta 36 de 110

Refer to the exhibit. Which route or routes will be advertised to the router ISP if autosummarization is enabled?

Selecciona una de las siguientes respuestas posibles:

10.0.0.0/8
10.1.0.0/16
10.1.0.0/28
10.1.1.0/24
10.1.2.0/24
10.1.3.0/24
10.1.4.0/28

Explicación

Pregunta 37 de 110

When are EIGRP update packets sent?

Selecciona una de las siguientes respuestas posibles:

only when necessary
every 30 seconds via broadcast
every 5 seconds via multicast
when learned routes age out

Explicación

Pregunta 38 de 110

Which requirement should be checked before a network administrator performs an IOS image upgrade on a router?

Selecciona una de las siguientes respuestas posibles:

The old IOS image file has been deleted.
The FTP server is operational.
There is sufficient space in flash memory.
The desired IOS image file has been downloaded to the router.

Explicación

Pregunta 39 de 110

What method of wireless authentication is dependent on a RADIUS authentication server?

Selecciona una de las siguientes respuestas posibles:

WPA Personal
WEP
WPA2 Enterprise
WPA2 Personal

Explicación

Pregunta 40 de 110

A network administrator wants to verify the default delay values for the interfaces on an EIGRP-enabled router. Which command will display these values?

Selecciona una de las siguientes respuestas posibles:

show running-config
show interfaces
show ip protocols
show ip route

Explicación

Pregunta 41 de 110

A network administrator in a branch office is configuring EIGRP authentication between the branch office router and the headquarters office router. Which security credential is needed for the authentication process?

Selecciona una de las siguientes respuestas posibles:

a randomly generated key with the crypto key generate rsa command
a common key configured with the key-string command inside a key chain
the username and password configured on the headquarters office router
the hostname of the headquarters office router and a common password

Explicación

Pregunta 42 de 110

Refer to the exhibit. Interface FastEthernet 0/1 on S1 is connected to Interface FastEthernet 0/1 on S2, and Interface FastEthernet 0/2 on S1 is connected to Interface FastEthernet 0/2 on S2. What are two errors in the present EtherChannel configurations? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Desirable mode is not compatible with on mode.
The trunk mode is not allowed for EtherChannel bundles.
Two auto modes cannot form a bundle.
The channel group is inconsistent.
The interface port channel ID should be different in both switches.

Explicación

Pregunta 43 de 110

Which port role is assigned to the switch port that has the lowest cost to reach the root bridge?

Selecciona una de las siguientes respuestas posibles:

disabled port
root port
designated port
non-designated port

Explicación

Pregunta 44 de 110

What are two features of OSPF interarea route summarization? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

ASBRs perform all OSPF summarization.
Routes within an area are summarized by the ABR.
Route summarization results in high network traffic and router overhead.
ABRs advertise the summarized routes into the backbone.
Type 3 and type 5 LSAs are used to propagate summarized routes.

Explicación

Pregunta 45 de 110

Launch PT Hide and Save PT

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

Which message was displayed on the web server?

Selecciona una de las siguientes respuestas posibles:

Work done!
Congratulations!
Wonderful work!
You’ve made it!

Explicación

Pregunta 46 de 110

Refer to the exhibit. What two pieces of information could be determined by a network administrator from this output? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

The metric that will be installed in the routing table for the 10.0.0.0 route will be 65 (64+1).
Interface Fa0/1 is not participating in the OSPF process.
R1 is the distribution point for the routers that are attached to the 10.0.0.4 network.
R1 is participating in multiarea OSPF.
The OSPF process number that is being used is 0.

Explicación

Pregunta 47 de 110

Match the CLI command prompt with the command or response entered when backing up a Release 15 IOS image to an IPv6 TFTP server. (Not all options are used.)

Arrastra la opción correcta a cada uno de los puntos naranjas

_ RouterA# _

Source Filename?

Address or name of remote host

Explicación

Pregunta 48 de 110

A network administrator has configured an EtherChannel between two switches that are connected via four trunk links. If the physical interface for one of the trunk links changes to a down state, what happens to the EtherChannel?

Selecciona una de las siguientes respuestas posibles:

Spanning Tree Protocol will recalculate the remaining trunk links.
The EtherChannel will remain functional.
The EtherChannel will transition to a down state.
Spanning Tree Protocol will transition the failed physical interface into forwarding mode.

Explicación

Pregunta 49 de 110

Refer to the exhibit. Which destination MAC address is used when frames are sent from the workstation to the default gateway?

Selecciona una de las siguientes respuestas posibles:

MAC addresses of both the forwarding and standby routers
MAC address of the standby router
MAC address of the virtual router
MAC address of the forwarding router

Explicación

Pregunta 50 de 110

Refer to the exhibit. A company has migrated from single area OSPF to multiarea. However, none of the users from network 192.168.1.0/24 in the new area can be reached by anyone in the Branch1 office. From the output in the exhibit, what is the problem?

Selecciona una de las siguientes respuestas posibles:

There are no interarea routes in the routing table for network 192.168.1.0.
The OSPF routing process is inactive.
The router has not established any adjacencies with other OSPF routers.
The link to the new area is down.

Explicación

Pregunta 51 de 110

What are two requirements when using out-of-band configuration of a Cisco IOS network device? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Telnet or SSH access to the device
a connection to an operational network interface on the device
a direct connection to the console or AUX port
a terminal emulation client
HTTP access to the device

Explicación

Pregunta 52 de 110

For troubleshooting missing EIGRP routes on a router, what three types of information can be collected using the show ip protocols command? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

any interfaces on the router that are configured as passive
any ACLs that are affecting the EIGRP routing process
any interfaces that are enabled for EIGRP authentication
networks that are unadvertised by the EIGRP routing protocol
the local interface that is used to establish an adjacency with EIGRP neighbors
the IP addresses that are configured on adjacent routers

Explicación

Pregunta 53 de 110

What are two requirements to be able to configure an EtherChannel between two switches? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

All the interfaces need to work at the same speed.
All interfaces need to be assigned to different VLANs.
The interfaces that are involved need to be contiguous on the switch.
All the interfaces need to be working in the same duplex mode.
Different allowed ranges of VLANs must exist on each end.

Explicación

Pregunta 54 de 110

54. Match each OSPF LSA description with its type. (Not all options are used.)

Arrastra la opción correcta a cada uno de los puntos naranjas

Only exists in multi & non-broad DR elec

describes routes to networks outside

flooded only within the area

advertise networks from other areas

Explicación

Pregunta 55 de 110

At a local college, students are allowed to connect to the wireless network without using a password. Which mode is the access point using?

Selecciona una de las siguientes respuestas posibles:

network
shared-key
open
passive

Explicación

Pregunta 56 de 110

What are three access layer switch features that are considered when designing a network? (Choose three.)

Selecciona una o más de las siguientes respuestas posibles:

broadcast traffic containment
forwarding rate
failover capability
Power over Ethernet
speed of convergence
port density

Explicación

Pregunta 57 de 110

Refer to the exhibit. What can be concluded about network 192.168.1.0 in the R2 routing table?

Selecciona una de las siguientes respuestas posibles:

This network has been learned from an internal router within the same area.
This network was learned through summary LSAs from an ABR.
This network is directly connected to the interface GigabitEthernet0/0.
This network should be used to forward traffic toward external networks.

Explicación

Pregunta 58 de 110

Which two statements are correct about EIGRP acknowledgment packets? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

The packets are sent as unicast.
The packets are unreliable.
The packets are used to discover neighbors that are connected on an interface.
The packets require confirmation.
The packets are sent in response to hello packets.

Explicación

Pregunta 59 de 110

An STP instance has failed and frames are flooding the network. What action should be taken by the network administrator?

Selecciona una de las siguientes respuestas posibles:

Broadcast traffic should be investigated and eliminated from the network.
Spanning tree should be disabled for that STP instance until the problem is located.
Redundant links should be physically removed until the STP instance is repaired.
A response from the network administrator is not required because the TTL field will eventually stop the frames from flooding the network.

Explicación

Pregunta 60 de 110

A network administrator issues the command R1(config)# license boot module c1900 technology-package securityk9 on a router. What is the effect of this command?

Selecciona una de las siguientes respuestas posibles:

The IOS will prompt the user to provide a UDI in order to activate the license.
The IOS will prompt the user to reboot the router.
The features in the Security package are available immediately.
The Evaluation Right-To-Use license for the Security technology package is activated.

Explicación

Pregunta 61 de 110

A router has been removed from the network for maintenance. A new Cisco IOS software image has been successfully downloaded to a server and copied into the flash of the router. What should be done before placing the router back into service?

Selecciona una de las siguientes respuestas posibles:

Delete the previous version of the Cisco IOS software from flash.
Copy the running configuration to NVRAM.
Back up the new image.
Restart the router and verify that the new image starts successfully.

Explicación

Pregunta 62 de 110

What are the two methods that are used by a wireless NIC to discover an AP? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

receiving a broadcast beacon frame
delivering a broadcast frame
transmitting a probe request
sending an ARP request
initiating a three-way handshake

Explicación

Pregunta 63 de 110

Refer to the exhibit. Why did R1 and R2 not establish ad adjacency?

Selecciona una de las siguientes respuestas posibles:

The link-local address must be the same on both routers.
The AS number must be the same on R1 and R2.
R1 S0/0/0 and R2 S0/0/0 are on different networks.
The no shutdown command is misapplied on both routers.
The router ID must be the same on both routers.

Explicación

Pregunta 64 de 110

Refer to the exhibit. Match the description to the corresponding value used by the DUAL FSM. (Not all options are used.)

Arrastra la opción correcta a cada uno de los puntos naranjas

feasible distance to 192.168.11.64

new successor to network 192.168.1.0

destination network

Explicación

Pregunta 65 de 110

Refer to the exhibit. Router CiscoVille has been partially configured for EIGRP authentication. What is missing that would allow successful authentication between EIGRP neighbors?

Selecciona una de las siguientes respuestas posibles:

The interfaces that will use EIGRP authentication must be specified.
The CiscoVIlle router requires a second keychain to function correctly when using two interfaces for EIGRP authentication.
The same key number must be used on any EIGRP neighbor routers.
The keychain for EIGRP authentication must be configured on the interfaces.

Explicación

Pregunta 66 de 110

Which Cisco IOS Software Release 15.0 technology pack is shipped with a permanent license on all Cisco ISR G2 devices?

Selecciona una de las siguientes respuestas posibles:

IPBase
DATA
Unified Communications
Security

Explicación

Pregunta 67 de 110

By default, how many equal cost routes to the same destination can be installed in the routing table of a Cisco router?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 68 de 110

What are two reasons to implement passive interfaces in the EIGRP configuration of a Cisco router? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

to provide increased network security
to shut down unused interfaces
to exclude interfaces from load balancing
to mitigate attacks coming from the interfaces
to avoid unnecessary update traffic

Explicación

Pregunta 69 de 110

What are two reasons to implement passive interfaces in the EIGRP configuration of a Cisco router? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

to provide increased network security
to shut down unused interfaces
to exclude interfaces from load balancing
to mitigate attacks coming from the interfaces
to avoid unnecessary update traffic

Explicación

Pregunta 70 de 110

What is a difference between the Cisco IOS 12 and IOS 15 versions?

Selecciona una de las siguientes respuestas posibles:

The IOS 12 version has commands that are not available in the 15 version.
IOS version 12.4(20)T1 is a mainline release, whereas IOS version 15.1(1)T1 is a new feature release.
The IOS version 15 license key is unique to each device, whereas the IOS version 12 license key is not device specific.
Every Cisco ISR G2 platform router includes a universal image in the IOS 12 versions, but not the IOS 15 versions.

Explicación

Pregunta 71 de 110

Rellena el espacio en blanco para completar el texto.

The spanning-tree mode configuration command is used to enable Rapid PVST+.

Explicación

Pregunta 72 de 110

A WLAN user wants to allocate an optimal amount of bandwidth to a specific online game. What is a Linksys Smart Wi-Fi tool that will allow the user to do this?

Selecciona una de las siguientes respuestas posibles:

Widgets
Speed Test
Media Prioritization
Bandwidth Prioritization

Explicación

Pregunta 73 de 110

When a Cisco router is configured with fast-switching, how are packets distributed over equal-cost paths?

Selecciona una de las siguientes respuestas posibles:

on a per-path-load basis
on a per-destination basis
on a per-interface basis
on a per-packet basis

Explicación

Pregunta 74 de 110

A network administrator is analyzing first-hop router redundancy protocols. What is a characteristic of VRRPv3?

Selecciona una de las siguientes respuestas posibles:

VRRPv3 is Cisco proprietary.
It supports IPv6 and IPv4 addressing.
It allows load balancing between routers.
It works together with HSRP.

Explicación

Pregunta 75 de 110

What is the purpose of the Cisco PAK?

Selecciona una de las siguientes respuestas posibles:

It is a proprietary encryption algorithm.
It is a compression file type used when installing IOS 15 or an IOS upgrade.
It is a way to compress an existing IOS so that a newer IOS version can be co-installed on a router.
It is a key for enabling an IOS feature set.

Explicación

Pregunta 76 de 110

What two license states would be expected on a new Cisco router once the license has been activated? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

License State: On
License State: Active, Registered
License Type: Permanent
License Type: ipbasek9
License Type: Temporary
License State: Active, In Use

Explicación

Pregunta 77 de 110

Which two channel group modes would place an interface in a negotiating state using PAgP? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

auto
desirable
on
passive
active

Explicación

Pregunta 78 de 110

If a company wants to upgrade a Cisco 2800 router from IOS 12.4T, what IOS should be recommended for a stable router platform?

Selecciona una de las siguientes respuestas posibles:

13.1T
12.5T
15.1M
14.0

Explicación

Pregunta 79 de 110

Rellena el espacio en blanco para completar el texto.

EIGRP keeps feasible successor routes in the table.

Explicación

Pregunta 80 de 110

A network engineer is troubleshooting a newly deployed wireless network that is using the latest 802.11 standards. When users access high bandwidth services such as streaming video, the wireless network performance is poor. To improve performance the network engineer decides to configure a 5 Ghz frequency band SSID and train users to use that SSID for streaming media services. Why might this solution improve the wireless network performance for that type of service?

Selecciona una de las siguientes respuestas posibles:

Requiring the users to switch to the 5 GHz band for streaming media is inconvenient and will result in fewer users accessing these services.
The 5 GHz band has a greater range and is therefore likely to be interference-free.
The 5 GHz band has more channels and is less crowded than the 2.4 GHz band, which makes it more suited to streaming multimedia.
The only users that can switch to the 5 GHz band will be those with the latest wireless NICs, which will reduce usage.

Explicación

Pregunta 81 de 110

What type of OSPF IPv4 route is indicated by a route table entry descriptor of O E1?

Selecciona una de las siguientes respuestas posibles:

an intra-area route that is advertised by the DR
a summary route that is advertised by an ABR
a directly connected route that is associated with an Ethernet interface
an external route that is advertised by an ASBR

Explicación

Pregunta 82 de 110

Which type of OSPF LSA represents an external route and is propagated across the entire OSPF domain?

Selecciona una de las siguientes respuestas posibles:

type 1
type 2
type 3
type 4
type 5

Explicación

Pregunta 83 de 110

A network administrator is analyzing the features that are supported by different first-hop router redundancy protocols. Which statement is a feature that is associated with GLBP?

Selecciona una de las siguientes respuestas posibles:

It uses a virtual router master.
GLBP allows load balancing between routers.
It works together with VRRP.
It is nonproprietary.

Explicación

Pregunta 84 de 110

A network administrator is analyzing the features that are supported by different first-hop router redundancy protocols. Which statement describes a feature that is associated with HSRP?

Selecciona una de las siguientes respuestas posibles:

HSRP uses active and standby routers.
HSRP is nonproprietary.
It uses ICMP messages in order to assign the default gateway to hosts.
It allows load balancing between a group of redundant routers.

Explicación

Pregunta 85 de 110

What is the purpose of a Cisco IOS 15 EM release?

Selecciona una de las siguientes respuestas posibles:

It specifies advanced IP services features such as advanced security and service provider packages.
It provides regular bug fix maintenance rebuilds, plus critical fix support for network-affecting bugs.
It is used for long-term maintenance, enabling customers to qualify, deploy, and remain on the release for an extended period.
It provides premium packages and enables additional IOS software feature combinations that address more complex network requirements.

Explicación

Pregunta 86 de 110

A network administrator is analyzing first -hop router redundancy protocols.What is characteristic of VRRPv3.

characteristics of VRRPV3:

Selecciona una o más de las siguientes respuestas posibles:

INTEROPERABILITY IN MULTI-VENDOR ENVIRONMENTS
VRRPv3 SUPPORTS USAGE OF IPv4 and IPv6
IMPROVE SCALABILITY THROUGH USE OF VRRS PATHWAYS
so judging from the options given it will be supports both IPv6 and IPv4 addressing

Explicación

Pregunta 87 de 110

What are two methods to make the OSPF routing protocol more secure? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Use only OSPFv3.
Use MD5 authentication.
When feasible, create a VPN tunnel between each OSPF neighbor adjacency.
Use the enable secret command.
Use the passive-interface command on LAN interfaces that are connected only to end-user devices.

Explicación

Pregunta 88 de 110

Which function is provided by EtherChannel?

Selecciona una de las siguientes respuestas posibles:

enabling traffic from multiple VLANs to travel over a single Layer 2 link
dividing the bandwidth of a single link into separate time slots
creating one logical link by using multiple physical links between two LAN switches
spreading traffic across multiple physical WAN links

Explicación

Pregunta 89 de 110

Which two parameters does EIGRP use by default to calculate the best path? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

transmit and receive load
delay
MTU
bandwidth
reliability

Explicación

Pregunta 90 de 110

Which wireless encryption method is the most secure?

Selecciona una de las siguientes respuestas posibles:

WPA
WPA2 with AES
WPA2 with TKIP
WEP

Explicación

Pregunta 91 de 110

What occurs when authentication is configured on an EIGRP router?

Selecciona una de las siguientes respuestas posibles:

After EIGRP authentication has been configured, the router must be rebooted to be able to reestablish adjacencies.
If adjacencies are displayed after the use of the show ipv6 eigrp neighbors command, then EIGRP authentication was successful.
Only one router is required to be configured for EIGRP authentication.
If only one router has been configured for EIGRP authentication, any prior adjacencies will remain intact.

Explicación

Pregunta 92 de 110

An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?

Selecciona una de las siguientes respuestas posibles:

as the maximum bandwidth of the fastest interface on the router
as the autonomous system number
as the length of time this router will wait to hear hello packets from a neighbor
as the number of neighbors supported by this router

Explicación

Pregunta 93 de 110

Refer to the exhibit. A network administrator is configuring PVST+ for the three switches.
What will be a result of entering these commands?

Selecciona una de las siguientes respuestas posibles:

S2 will set the priority value for VLAN 10 to 24576
S1 will set the priority value for VLAN 20 to 24596
S3 will set the priority value for VLAN 30 to 8192
S1 will set the priority value for VLAN 10 to 0

Explicación

Pregunta 94 de 110

Which two conditions should the network administrator verify before attempting to upgrade a Cisco IOS image using a TFTP server? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Verify connectivity between the router and TFTP server using the ping command.
Verify that there is enough flash memory for the new Cisco IOS image using the show flash command.
Verify the name of the TFTP server using the show hosts command.
Verify that the TFTP server is running using the tftpdnld command.
Verify that the checksum for the image is valid using the show version command.

Explicación

Pregunta 95 de 110

An EIGRP router loses the route to a network. Its topology table contains two feasible successors to the same network. What action will the router take?

Selecciona una de las siguientes respuestas posibles:

The router will query neighbors for an alternate route.
The router uses the default route.
The DUAL algorithm is recomputed to find an alternate route.
The best alternative backup route is immediately inserted into the routing table.

Explicación

Pregunta 96 de 110

What are two drawbacks to turning spanning tree off and having multiple paths through the Layer 2 switch network? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Broadcast frames are transmitted indefinitely.
Port security shuts down all of the port that attached devices.
The switch acts like a hub.
The Mac address table becomes unstable.
Port security becomes unstable.

Explicación

Pregunta 97 de 110

What is the function of STP in a scalable network?

Selecciona una de las siguientes respuestas posibles:

It combines multiple switch trunk links to act as one logical link for increased bandwidth.
It decreases the size of the failure domain to contain the impact of failures.
It protects the edge of the enterprise network from malicious activity.
It disables redundant paths to eliminate Layer 2 loops.

Explicación

Pregunta 98 de 110

Match the OSPF router type description with its name

Arrastra la opción correcta a cada uno de los puntos naranjas

identical LSDBs

maintain separate LSDBs for each area

Import non-OSPF network info to OSPF

Explicación

Pregunta 99 de 110

What is a requirement to configure a trunking EtherChannel between two switches?

Selecciona una de las siguientes respuestas posibles:

The participating interfaces must be on the same module on a switch.
The participating interfaces must be physically contiguous on a switch.
The participating interfaces must be assigned the same VLAN number on both switches.
The allowed range of VLANs must be the same on both switches.

Explicación

Pregunta 100 de 110

What should be installed on a Cisco router as a prerequisite for installing the Data, Security, and Unified Communications licenses in IOS 15?

Selecciona una de las siguientes respuestas posibles:

the IP Base license
the Cisco License Manager
the Enterprise Services package
the Enterprise Base license

Explicación

Pregunta 101 de 110

After implementing an IPv6 network, the administrator notices that the OSPFv3 process is not starting on the routers. What could be the problem?

Selecciona una de las siguientes respuestas posibles:

No router IDs are configured on the routers.
Authentication was not implemented between the routers.
The routers were not configured with the network command.
The routers are configured with the default priority.

Explicación

Pregunta 102 de 110

Which statement describes the load balancing behavior of EIGRP?

Selecciona una de las siguientes respuestas posibles:

EIGRP for IPv6 supports unequal cost load balancing, but EIGRP for IPv4 does not.
EIGRP for IPv4 supports unequal cost load balancing, but EIGRP for IPv6 does not.
Neither EIGRP for IPv4 nor EIGRP for IPv6 support unequal cost load balancing.
Both EIGRP for IPv4 and EIGRP for IPv6 support unequal cost load balancing.

Explicación

Pregunta 103 de 110

What is the purpose of the Cisco License Manager?

Selecciona una de las siguientes respuestas posibles:

It is a free software application that helps network administrators rapidly deploy multiple Cisco software licenses across their networks.
It is software that provides the Product Activation Key for the license and important information regarding the Cisco End User License Agreement.
It is software that comes pre-installed with the software image and contains licenses for the customer-specified packages and features.
It is a web-based portal for getting and registering individual software licenses.

Explicación

Pregunta 104 de 110

While attending a conference, participants are using laptops for network connectivity. When a guest speaker attempts to connect to the network, the laptop fails to display any available wireless networks. The access point is probably operating in which mode?

Selecciona una de las siguientes respuestas posibles:

passive
mixed
open
active

Explicación

Pregunta 105 de 110

Refer to the exhibit and the following error message from the SwB switch.
00:22:43: %SPANTREE-7-RECV_1Q_NON_TRUNK: Received 802.1Q BPDU on non trunk FastEthernet0/1 VLAN1.
00:22:43: %SPANTREE-7-BLOCK_PORT_TYPE: Blocking FastEthernet0/1 on VLAN0001. Inconsistent port type.
Considering that the link between the two switches is good and the correct type, what could cause this error message?

Selecciona una de las siguientes respuestas posibles:

The SwA port has IEEE 802.1Q trunking enabled and the SwB port has ISL trunking enabled.
The SwA port is configured as a trunk port and the SwB port is configured as an access port.
The Spanning Tree Protocol has been disabled on both switches.
The Spanning Tree Protocol has been disabled on one switch.
The IEEE 802.1Q trunking port has a speed mismatch on one of the switches.

Explicación

Pregunta 106 de 110

Which statement describes a characteristic of OSPF external routes?

Selecciona una de las siguientes respuestas posibles:

Type 1 and type 2 external routes in IPv4 networks are represented in the routing table by EX1 and EX2, respectively.
The cost of a type 1 route is always the external cost, regardless of the interior cost to reach that route.
A type 2 route is always preferred over a type 1 route for the same destination.
The difference between type 1 and type 2 is in the way the cost of the route is being calculated.

Explicación

Pregunta 107 de 110

A network administrator is designing a wireless network for a new school building. The wireless network is for students using their own mobile devices. The network administrator wants to provide the most throughput possible even if the throughput is reduced by students using older devices. Which technology would be best in this situation?

Selecciona una de las siguientes respuestas posibles:

802.11g
802.11ac
802.11n
802.11ad

Explicación

Pregunta 108 de 110

A company has deployed four 48-port access layer switches to a switch bock. For redundancy each access layer switch will connect to two distribution layer switches. Additionally, link aggregation will be used to combine 10 Gbps interfaces to form 20 Gbps trunk links form the access layer switches to the distribution layer switches. How many switch ports on the access layer switches will be available in the switch block to support end devices?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 109 de 110

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?

Selecciona una de las siguientes respuestas posibles:

Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
Configure both routers with the same EIGRP process ID.
Enable the serial interfaces of both routers.

Explicación

Pregunta 110 de 110

What is a feature of the OSPF routing protocol?

Selecciona una de las siguientes respuestas posibles:

OSPF authentication is configured in the same way on IPV4 and IPV6 networks
The SPF algorithm chooses the best path based on 30-second updates
Routers can be grouped into autonomous systems to support a hierarchical system.
It scales well in both small and large networks.

Explicación

Revisar respuesta

["https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482339/desktop_f62830c0-7894-4302-bfae-42a91cafb1a0.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482348/desktop_3cb3aa0f-3348-4be6-be36-1bab25711e50.png","https://cdn.goconqr.com/uploads/checkbox_question/image/3482355/desktop_ad73c189-879e-4437-9a7f-c346dc001f83.png","https://cdn.goconqr.com/uploads/checkbox_question/image/3482483/desktop_c240d5cb-5424-4431-8479-6ad1ae16f0b9.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482535/desktop_fc73ed60-570a-4fe7-ac77-ea8787c9d4f7.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482543/desktop_692e04d9-3c53-4a33-864b-9f9b55d3ff51.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482548/desktop_364c5263-5e7d-4446-bf09-26a526b613ad.png","https://cdn.goconqr.com/uploads/checkbox_question/image/3482555/desktop_ce98bd62-7b4e-4a77-a525-d628617c3be3.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482564/desktop_30e2b81b-628b-4794-8154-6151ccdfc218.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482608/desktop_cfd33611-1d23-4f16-82ae-c6f06bc9657c.png","https://cdn.goconqr.com/uploads/checkbox_question/image/3482633/desktop_9572d698-b6dd-4d1f-8bef-3072565a73fe.png","https://cdn.goconqr.com/uploads/checkbox_question/image/3482676/desktop_ae8cec3b-159c-4ca9-a15a-4bea6e2d0f8e.png","https://cdn.goconqr.com/uploads/label_image_drag_and_drop_question/image/3482692/image_primary_816cc303-fd62-45eb-b15f-5599a54b4c2f.jpeg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482702/desktop_e0739191-2a6b-4946-b40c-455aba676c0b.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3482705/desktop_cb071fc3-4b64-4cc6-a880-566bc69d5447.png","https://cdn.goconqr.com/uploads/label_image_drag_and_drop_question/image/3482737/image_primary_59be48ec-6423-42c6-b202-dfa0d53b2ada.jpeg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3484696/desktop_0ada4189-3b27-4515-a280-4e917c379a30.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3484718/desktop_16302d87-b3be-4356-89bd-9c960974d35a.png","https://cdn.goconqr.com/uploads/label_image_drag_and_drop_question/image/3484771/image_primary_5107401f-a4cd-47eb-b67f-f25bed764557.jpeg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3484778/desktop_d7b456a3-c7fc-4229-86ad-2cf08d851ac5.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3485092/desktop_ea9c3729-de37-4aca-ac4a-deb8ab20a566.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3485101/desktop_71e7ce3d-71a1-4f31-8714-c445deaac9b6.png","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3485124/desktop_3f65f0cd-3c27-49f7-be88-f4ee1cffffe4.png","https://cdn.goconqr.com/uploads/label_image_drag_and_drop_question/image/3485143/image_primary_cb46d7f8-4923-4dc6-b58f-308276af54f3.jpeg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/3485210/desktop_10c1ab7a-7817-4ce1-8ee0-0f33c7f71c0e.jpeg"]

	Creado por Christina Evans hace más de 8 años

sophomore CCNA 3 Test sobre CCNA 3V5.03 Final B, creado por Christina Evans el 24/07/2016.

CCNA 3V5.03 Final B

Pregunta 1 de 110

A network designer is considering whether to implement a switch block on the company network. What is the primary advantage of deploying a switch block?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 2 de 110

Refer to the exhibit. A network administrator is attempting to upgrade the IOS system image on a Cisco 2901 router. After the new image has been downloaded and copied to the TFTP server, what command should be issued on the router before the IOS system image is upgraded on the router?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 3 de 110

Rellena el espacio en blanco para completar el texto.

The area interconnects with all other OSPF area types.

Explicación

Pregunta 4 de 110

In a large enterprise network, which two functions are performed by routers at the distribution layer? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 5 de 110

Which address is used by an IPv6 EIGRP router as the source for hello messages?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 6 de 110

Refer to the exhibit. Which switch will be the root bridge after the election process is complete?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 7 de 110

Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 8 de 110

Refer to the exhibit. A network administrator issues the show ipv6 eigrp neighbors command. Which conclusion can be drawn based on the output?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 9 de 110

Which characteristic would most influence a network design engineer to select a multilayer switch over a Layer 2 switch?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 10 de 110

Refer to the exhibit. Which two conclusions can be derived from the output? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 11 de 110

What two conditions have to be met in order to form a cluster that includes 5 access points? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 12 de 110

Which technological factor determines the impact of a failure domain?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 13 de 110

Which mode configuration setting would allow formation of an EtherChannel link between switches SW1 and SW2 without sending negotiation traffic?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 14 de 110

A network engineer is implementing security on all company routers. Which two commands must be issued to force authentication via the password 1C34dE for all OSPF-enabled interfaces in the backbone area of the company network? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 15 de 110

When does an OSPF router become an ABR?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 16 de 110

A network administrator enters the spanning-tree portfast bpduguard default command. What is the result of this command being issued on a Cisco switch?

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 17 de 110

Refer to the exhibit. What are two results of issuing the displayed commands on S1, S2, and S3? (Choose two.)

Selecciona una o más de las siguientes respuestas posibles:

Explicación

Pregunta 18 de 110

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 19 de 110

Selecciona una de las siguientes respuestas posibles:

Explicación

Pregunta 20 de 110

When should EIGRP automatic summarization be turned off?

Selecciona una de las siguientes respuestas posibles:

Explicación