Jari Van Meirvenne
Quiz por , criado more than 1 year ago

CCNA Questions not on the online test exam

629
0
0
Jari Van Meirvenne
Criado por Jari Van Meirvenne quase 9 anos atrás
Fechar

CCNA

CCNA

Questão 1 de 36

1

Which three pairs of trunking modes will establish a functional trunk link between two Cisco switches? (Choose three.)

Selecione uma ou mais das seguintes:

  • dynamic desirable – dynamic auto

  • dynamic desirable – dynamic desirable

  • dynamic desirable – trunk

  • dynamic auto – dynamic auto

  • access – dynamic auto

  • access – trunk

Explicação

Questão 2 de 36

1

Preencha o espaço em branco para completar o texto.

Fill in the blank.
The OSPF Type 1 packet is the packet.

Explicação

Questão 3 de 36

1

Which value represents the “trustworthiness” of a route and is used to determine which route to install into the routing table when there are multiple routes toward the same destination?

Selecione uma das seguintes:

  • routing protocol

  • outgoing interface

  • metric

  • administrative distance

Explicação

Questão 4 de 36

1

Preencha o espaço em branco para completar o texto.

Fill in the blank.

The default administrative distance for a static route is

Explicação

Questão 5 de 36

1

Preencha o espaço em branco para completar o texto.

Static routes are configured by the use of the global configuration command

Explicação

Questão 6 de 36

1

Refer to the exhibit. If the switch reboots and all routers have to re-establish OSPF adjacencies, which routers will become the new DR and BDR?

Selecione uma das seguintes:

  • Router R3 will become the DR and router R1 will become the BDR.

  • Router R1 will become the DR and router R2 will become the BDR.

  • Router R4 will become the DR and router R3 will become the BDR

Explicação

Questão 7 de 36

1

What is the purpose of an access list that is created as part of configuring IP address translation?

Selecione uma das seguintes:

  • The access list permits or denies specific addresses from entering the device doing the translation.

  • The access list defines the private IP addresses that are to be translated

  • The access list prevents external devices from being a part of the address translation.

  • The access list defines the valid public addresses for the NAT or PAT pool.

Explicação

Questão 8 de 36

1

The computers used by the network administrators for a school are on the 10.7.0.0/27 network. Which two commands are needed at a minimum to apply an ACL that will ensure that only devices that are used by the network administrators will be allowed Telnet access to the routers? (Choose two.)

Selecione uma ou mais das seguintes:

  • -ip access-group 5 out

  • -access-list standard VTY
    permit 10.7.0.0 0.0.0.127

  • -access-list 5 deny any

  • -access-list 5 permit 10.7.0.0 0.0.0.31

  • -ip access-group 5 in

  • -access-class 5 in

Explicação

Questão 9 de 36

1

While analyzing log files, a network administrator notices reoccurring native VLAN mismatches. What is the effect of these reoccurring errors?

Selecione uma das seguintes:

  • The control and management traffic on the error-occurring trunk port is being misdirected or dropped.

  • Unexpected traffic on the error-occurring trunk port is being received.​

  • All traffic on the error-occurring trunk port is being misdirected or dropped.

  • All traffic on the error-occurring trunk port is being switched correctly regardless of the error.

Explicação

Questão 10 de 36

1

Which two characteristics describe the native VLAN? (Choose two.)

Selecione uma ou mais das seguintes:

  • This VLAN is necessary for remote management of a switch.

  • Designed to carry traffic that is generated by users, this type of VLAN is also known as the default VLAN.

  • The native VLAN provides a common identifier to both ends of a trunk

  • The native VLAN traffic will be untagged across the trunk link.

  • High priority traffic, such as voice traffic, uses the native VLAN.

Explicação

Questão 11 de 36

1

Refer to the exhibit. The Branch Router has an OSPF neighbor relationship with the HQ router over the 198.51.0.4/30 network. The 198.51.0.8/30 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/1/1 100 was issued on Branch and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up?

Selecione uma das seguintes:

  • Add the next hop neighbor address of 198.51.0.8.

  • Change the administrative distance to 1.

  • Change the destination network to 198.51.0.5.

  • Change the administrative distance to 120

Explicação

Questão 12 de 36

1

Refer to the exhibit. An attacker on PC X sends a frame with two 802.1Q tags on it, one for VLAN 40 and another for VLAN 12. What will happen to this frame?

Selecione uma das seguintes:

  • SW-A will drop the frame because it is invalid.

  • SW-A will leave both tags on the frame and send it to SW-B, which will forward it to hosts on VLAN 40.

  • SW-A will remove both tags and forward the rest of the frame across the trunk link, where SW-B will forward the frame to hosts on VLAN 40.

  • SW-A will remove the outer tag and send the rest of the frame across the trunk link, where SW-B will forward the frame to hosts on VLAN 12.

Explicação

Questão 13 de 36

1

Which statement is true about the difference between OSPFv2 and OSPFv3?

Selecione uma das seguintes:

  • OSPFv3 routers use a different metric than OSPFv2 routers use.

  • OSPFv3 routers do not need to elect a DR on multiaccess segments.

  • OSPFv3 routers do not need to have matching subnets to form neighbor adjacencies.

  • OSPFv3 routers use a 128 bit router ID instead of a 32 bit ID.

Explicação

Questão 14 de 36

1

What are two ways of turning off DTP on a trunk link between switches? (Choose two.)

Selecione uma ou mais das seguintes:

  • Change the native VLAN on both ports.

  • Configure attached switch ports with the nonegotiate command option.

  • Configure attached switch ports with the dynamic desirable command option.

  • Configure one port with the dynamic auto command option and the opposite attached switch port with the dynamic desirable command option.

  • Place the two attached switch ports in access mode.

Explicação

Questão 15 de 36

1

Why would an administrator use a network security auditing tool to flood the switch MAC address table with fictitious MAC addresses?

Selecione uma das seguintes:

  • to determine if the switch is forwarding the broadcast traffic correctly

  • to determine which ports are functioning

  • to determine which ports are not correctly configured to prevent MAC address flooding

  • to determine when the CAM table size needs to be increased in order to prevent overflows

Explicação

Questão 16 de 36

1

A new network policy requires an ACL to deny HTTP access from all guests to a web server at the main office. All guests use addressing from the IPv6 subnet 2001:DB8:19:C::/64. The web server is configured with the address 2001:DB8:19:A::105/64. Implementing the NoWeb ACL on the interface for the guest LAN requires which three commands? (Choose two.)

Selecione uma ou mais das seguintes:

  • permit tcp any host 2001:DB8:19:A::105 eq 80

  • deny tcp host 2001:DB8:19:A::105 any eq 80

  • deny tcp any host 2001:DB8:19:A::105 eq 80

  • permit ipv6 any any

  • deny ipv6 any any

  • ipv6 traffic-filter NoWeb in

  • p access-group NoWeb in

Explicação

Questão 17 de 36

1

An OSPF router has three directly connected networks; 172.16.0.0/16, 172.16.1.0/16, and 172.16.2.0/16. Which OSPF network command would advertise only the 172.16.1.0 network to neighbors?

Selecione uma das seguintes:

  • router(config-router)# network 172.16.1.0 0.0.255.255 area 0

  • router(config-router)# network 172.16.0.0 0.0.15.255 area 0

  • router(config-router)# network 172.16.1.0 255.255.255.0 area 0

  • router(config-router)# network 172.16.1.0 0.0.0.0 area 0

Explicação

Questão 18 de 36

1

Refer to the exhibit. Which type of IPv6 static route is configured in the exhibit?

Selecione uma das seguintes:

  • fully specified static route

  • recursive static route

  • directly attached static route

  • floating static route

Explicação

Questão 19 de 36

1

Which subnet mask would be used as the classful mask for the IP address 192.135.250.27?

Selecione uma das seguintes:

  • 255.0.0.0

  • 255.255.0.0

  • 255.255.255.0

  • 255.255.255.224

Explicação

Questão 20 de 36

1

Which subnet mask would be used as the classful mask for the IP address 128.107.52.27?

Selecione uma das seguintes:

  • 255.0.0.0

  • 255.255.0.0

  • 255.255.255.0

  • 255.255.255.224

Explicação

Questão 21 de 36

1

The buffers for packet processing and the running configuration file are temporarily stored in which type of router memory?

Selecione uma das seguintes:

  • Flash

  • NVRAM

  • RAM

  • ROM

Explicação

Questão 22 de 36

1

A network technician is configuring port security on switches. The interfaces on the switches are configured in such a way that when a violation occurs, packets with unknown source address are dropped and no notification is sent. Which violation mode is configured on the interfaces?

Selecione uma das seguintes:

  • off

  • restrict

  • protect

  • shutdown

Explicação

Questão 23 de 36

1

A standard ACL has been configured on a router to allow only clients from the 10.11.110.0/24 network to telnet or to ssh to the VTY lines of the router. Which command will correctly apply this ACL?

Selecione uma das seguintes:

  • access-group 11 in

  • access-class 11 in

  • access-list 11 in

  • access-list 110 in

Explicação

Questão 24 de 36

1

What address will summarize the LANs attached to routers 2-A and 3-A and can be configured in a summary static route to advertise them to an upstream neighbor?

Selecione uma das seguintes:

  • 10.0.0.0/24

  • 10.0.0.0/23

  • 10.0.0.0/22

  • 10.0.0.0/21

Explicação

Questão 25 de 36

1

A security specialist designs an ACL to deny access to a web server from all sales staff. The sales staff are assigned addressing from the IPv6 subnet 2001:db8:48:2c::/64. The web server is assigned the address 2001:db8:48:1c::50/64. Configuring the WebFilter ACL on the LAN interface for the sales staff will require which three commands? (Choose three.)

Selecione uma ou mais das seguintes:

  • deny tcp host 2001:db8:48:1c::50 any eq 80

  • deny tcp any host 2001:db8:48:1c::50 eq 80

  • permit tcp any host 2001:db8:48:1c::50 eq 80

  • permit ipv6 any any

  • deny ipv6 any any

  • ip access-group WebFilter in

  • ipv6 traffic-filter WebFilter in

Explicação

Questão 26 de 36

1

To enable RIP routing for a specific subnet, the configuration command network 192.168.5.64 was entered by the network administrator. What address, if any, appears in the running configuration file to identify this network?

Selecione uma das seguintes:

  • 192.168.5.64

  • 192.168.5.0

  • 192.168.0.0

  • No address is displayed.

Explicação

Questão 27 de 36

1

Refer to the exhibit. An ACL preventing FTP and HTTP access to the interval web server from all teaching assistants has been implemented in the Board Office. The address of the web server is 172.20.1.100 and all teaching assistants are assigned addresses in the 172.21.1.0/24 network. After implement the ACL, access to all servers is denied. What is the problem?

Selecione uma das seguintes:

  • inbound ACLs must be routed before they are processed

  • the ACL is implicitly denying access to all the servers

  • named ACLs requite the use of port numbers

  • the ACL is applied to the interface using the wrong direction

Explicação

Questão 28 de 36

1

Preencha o espaço em branco para completar o texto.

a router learns of multiple toward the same destination. Which value in a routing table replesents the trustworthiness of learned routes and is used by the router to determine which route to install into the routing table for specific situation

Explicação

Questão 29 de 36

1

What is the minimum configuration for a router interface that is participating in IPv6 routing?

Selecione uma das seguintes:

  • to have only a link-local IPv6 address

  • to not have only a link-local IPv6 address

Explicação

Questão 30 de 36

1

Which two statements are true about half-duplex and full-duplex communications?

Selecione uma ou mais das seguintes:

  • Full duplex offers 100 percent potential use of the bandwidth.

  • Full duplex allows both ends to transmit and receive simultaneously.

Explicação

Questão 31 de 36

1

Preencha o espaço em branco para completar o texto.

The acronym describes the type of traffic that has strict QoS requirements and utilizes a one-way overall delay less than 150 ms across the network

Explicação

Questão 32 de 36

1

Which two commands should be implemented to return a Cisco 3560 trunk port to its default configuration? (Choose two.)

Selecione uma ou mais das seguintes:

  • S1(config-if)# no switchport trunk native vlan

  • S1(config-if)# no switchport trunk allowed vlan

Explicação

Questão 33 de 36

1

Which command will enable auto-MDIX on a device

Selecione uma das seguintes:

  • S1(config-if)# mdix auto

  • S1(config-if)# mdix mono

Explicação

Questão 34 de 36

1

What is the effect of issuing the passive-interface default command on a router that is configured for OSPF?

Selecione uma das seguintes:

  • It prevents OSPF messages from being sent out any OSPF-enabled interface.

  • It doesn't prevents OSPF messages from being sent out any OSPF-enabled interface.

Explicação

Questão 35 de 36

1

Refer to the exhibit. A network administrator has just configured address translation and is verifying the configuration. What three things can the administrator verify? (Choose three.)

Selecione uma ou mais das seguintes:

  • The name of the NAT pool is refCount.

  • A standard access list numbered 1 was used as part of the configuration process.

  • Address translation is working.

Explicação

Questão 36 de 36

1

Selecione das listas do Menu para completar o texto.

A. flash( console access, full operating system, limited operating system, routing table, startup configuration file )

B. NVRAM( console access, full operating system, limited operating system, routing table, startup configuration file )

C. RAM( console access, full operating system, limited operating system, routing table, startup configuration file )

D. ROM( console access, full operating system, limited operating system, routing table, startup configuration file )

Explicação

Anterior
Verificar resposta
Próximo