R&R Basics- CH 4 & 5 Exam

1

Consider the following routing table entry for R1:
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
What is the significance of the Serial0/0/0?

1

What are two common types of static routes in routing tables? (Choose two)

1

What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.)

1

Which two items are used by a host device when performing an ANDing operation to determine if a destination address is on the same local network? (Choose two.)

1

Refer to the exhibit. A network administrator issues the show ipv6 route command on R1. What two conclusions can be drawn from the routing table? (Choose two.)

1

What route would have the lowest administrative distance?

1

When a router receives a packet, it examines the destination address of the packet and looks in the table to determine the best path to use to forward the packet.

1

Refer to the exhibit. PC A sends a request to Server B. What IPv4 address is used in the destination field in the packet as the packet leaves PC A?

1

What are two functions of a router? (Choose two.)

1

Refer to the exhibit. What will the router do with a packet that has a destination IP address of 192.168.12.227?

1

Which statement describes a route that has been learned dynamically?

1

Refer to the exhibit. A network administrator has configured R1 as shown. When the administrator checks the status of the serial interface, the interface is shown as being administratively down. What additional command must be entered on the serial interface of R1 to bring the interface up?

1

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?

1

Refer to the exhibit. If PC1 is sending a packet to PC2 and routing has been configured between the two routers, what will R1 do with the Ethernet frame header attached by PC1?

1

Which software is used for a network administrator to make the initial router configuration securely?

1

In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.)

1

What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server?

1

A packet moves from a host on one network to a device on a remote network within the same company. If NAT is not performed on the packet, which two items remain unchanged during the transfer of the packet from source to destination? (Choose two.)

1

What is a characteristic of an IPv4 loopback interface on a Cisco IOS router?

1

Refer to the exhibit.
What does R1 use as the MAC address of the destination when constructing the frame that will go from R1 to Server B?

1

A network administrator configures the interface fa0/0 on the router R1 with the command ip address 172.16.1.254 255.255.255.0. However, when the administrator issues the command show ip route, the routing table does not show the directly connected network. What is the possible cause of the problem?

1

Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)

1

Which two parameters are used by EIGRP as metrics to select the best path to reach a network? (Choose two.)

1

What is a disadvantage of using router-on-a-stick inter-VLAN routing?

1

How are IP addressing designs affected by VLAN implementations?

1

Refer to the exhibit. In this network design, which connection or connections if any, add the VLAN ID number if host H1 sends information to host H2?

1

What is a characteristic of legacy inter-VLAN routing?

1

Refer to the exhibit. A network administrator needs to configure router-on-a-stick for the networks that are shown. How many subinterfaces will have to be created on the router if each VLAN that is shown is to be routed and each VLAN has its own subinterface?

1

Refer to the exhibit. What is the problem with this configuration, based on the output of the router?

1

What condition is required to enable Layer 3 switching?

1

Refer to the exhibit. Communication between the VLANs is not occurring. What could be the issue?

1

Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Users complain that PCs on different VLANs cannot communicate. Based on the output, what are two configuration errors on switch interface Gi1/1? (Choose two.)

1

Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Users complain that PC2 cannot communicate with PC1. Based on the output, what is the possible cause of the problem?

1

Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Based on the partial output that is displayed by the use of the show vlan command, which conclusion can be drawn for the Gi1/1 interface?

1

Inter-VLAN communication is not occurring in a particular building of a school. Which two commands could the network administrator use to verify that inter-VLAN communication was working properly between a router and a Layer 2 switch when the router-on-a-stick design method is implemented? (Choose two.)

1

What is a characteristic of a routed port on a Layer 3 switch?

1

While configuring inter-VLAN routing on a multilayer switch, a network administrator issues the no switchport command on an interface that is connected to another switch. What is the purpose of this command?

1

What is a disadvantage of using multilayer switches for inter-VLAN routing?

1

How is traffic routed between multiple VLANs on a multilayer switch?

1

An administrator is attempting to configure a static route on a Cisco 2960 series switch. After the administrator types the command ip route 0.0.0.0 0.0.0.0 10.1.1.1, an error message appears stating that the command is not recognized. What must the administrator do so that this command is accepted?

1

Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.35 and a destination address of 192.168.1.85. What will the router do with this packet?

1

Refer to the exhibit. After attempting to enter the configuration that is shown in router RTA, an administrator receives an error and users on VLAN 20 report that they are unable to reach users on VLAN 30. What is causing the problem?

1

Refer to the exhibit. A network administrator is configuring RT1 for inter-VLAN routing. The switch is configured correctly and is functional. Host1, Host2, and Host3 cannot communicate with each other. Based on the router configuration, what is causing the problem?

1

Refer to the exhibit. In what switch mode should port G0/1 be assigned if Cisco best practices are being used?

1

Refer to the exhibit. Which command can the administrator issue to change the VLAN10 status to up?

1

A network engineer is troubleshooting the configuration of new VLANs on a network. Which command is used to display the list of VLANs that exists on the switch?

1

Which statement describes a disadvantage of using router subinterfaces for inter-VLAN routing?

R&R Basics- CH 4 & 5 Exam

R&R Basics- CH 4 & 5 Exam

Consider the following routing table entry for R1: D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0 What is the significance of the Serial0/0/0?

What are two common types of static routes in routing tables? (Choose two)

What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.)

Which two items are used by a host device when performing an ANDing operation to determine if a destination address is on the same local network? (Choose two.)

Refer to the exhibit. A network administrator issues the show ipv6 route command on R1. What two conclusions can be drawn from the routing table? (Choose two.)

What route would have the lowest administrative distance?

When a router receives a packet, it examines the destination address of the packet and looks in the table to determine the best path to use to forward the packet.

Refer to the exhibit. PC A sends a request to Server B. What IPv4 address is used in the destination field in the packet as the packet leaves PC A?

What are two functions of a router? (Choose two.)

Refer to the exhibit. What will the router do with a packet that has a destination IP address of 192.168.12.227?

Which statement describes a route that has been learned dynamically?

Refer to the exhibit. A network administrator has configured R1 as shown. When the administrator checks the status of the serial interface, the interface is shown as being administratively down. What additional command must be entered on the serial interface of R1 to bring the interface up?

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?

Refer to the exhibit. If PC1 is sending a packet to PC2 and routing has been configured between the two routers, what will R1 do with the Ethernet frame header attached by PC1?

Which software is used for a network administrator to make the initial router configuration securely?

In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.)

What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server?

A packet moves from a host on one network to a device on a remote network within the same company. If NAT is not performed on the packet, which two items remain unchanged during the transfer of the packet from source to destination? (Choose two.)

What is a characteristic of an IPv4 loopback interface on a Cisco IOS router?

Refer to the exhibit. What does R1 use as the MAC address of the destination when constructing the frame that will go from R1 to Server B?

Consider the following routing table entry for R1:
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
What is the significance of the Serial0/0/0?

Refer to the exhibit.
What does R1 use as the MAC address of the destination when constructing the frame that will go from R1 to Server B?