Technician Review Questions Part 2

1

What is the recommended power range for microscopes to view the end face of an optical fiber connector

1

_____ cabling provides interconnection between TRs, ERs, main terminal space & EF (entrance facilities)

1

To confine the light within the core by creating a reflective boundary is the purpose of the _______

1

This space is a special purpose room that provides and maintains a suitable operating environment for large telecommunications equipment

1

During a retrofit, it is not required to remove all abandoned cable

1

This space should not serve more than 3,600 sq/ft

1

What is the most common specialty fastener used in ITS cabling

1

Interbuilding circuits are considered to have lightning exposure unless 1 or more conditions exist (select all correct)

1

This tester uses Rayleigh scattering & Fresnal reflection to measure the characteristics of an optical fiber

1

The ITS installer is allowed to add more firestopping product to get a higher rating

1

Cross-Connect Field Colors: Future (Key Telephone Systems)

1

What is used to flush electrolyte burns to the skin

1

Shorter wavelengths of light exhibit greater amounts of attenuation because of Rayleigh scattering

1

Longer wavelengths are more sensitive to bending loss and will allow light to exit out of the fiber core more than shorter wavelengths

1

What is the minimum separation of telecommunications cabling and electric motors & transformers

1

This firestop material has the ability to absorb heat to prevent the temperature from rising on the other side of the fire barrier

1

Where does the SCS begin

1

What is the signal range for POTS

1

This type of protector has a reaction time of 1-2 ns

1

Cross-Connect Field Colors: Interbuilding Backbone

1

The frequency of CAT5e is

1

The frequency of CAT3 is

1

The frequency of CAT6a is

1

The frequency of CAT6 is

1

How many pairs are in a super group

1

How many binder groups are in each super group

1

What are the 2 common methods of terminating balanced twisted pair cable (select all correct)

1

Which of the following cables meet the minimum requirements for cabling to a work area (select all correct)

1

Why is undercarpet cable not recommended (select all correct)

1

The interconnection between undercarpet cable and horizontal cable is called what

1

If using undercarpet cable, what is recommended maximum length of the cable

1

What are the most common connectors for multimode fiber (select all correct)

1

What are the common modular connectors used in ITS (select all correct)

1

What are the most predominant coaxial cables (select all correct)

1

The F connector is the most commonly used connector for residential cable service

1

What are the common BNC connector types (select all correct)

1

What is the maximum pulling tension of 4-pair, balanced twisted pair cabling

1

What is the minimum bend radius of 4 pair cable

1

What is the recommended service slack for 4-pair cables at the work area

1

What is the recommended service slack for a 4 pair cable in the TR/ER

1

What is the recommended service slack for multipair cable in a TR/ER

1

What is the recommended service slack for 4 pair & multipair cable at a TE

1

The tensile strength of pull string is typically

1

A pull string should be attached to cable with what type of knot and how many knots

1

Structural steel members (red iron) can be used to support cables if they are spaced 4-5ft

1

What are the common splice connectors for copper (select all correct)

1

What are the common splice enclosures (select all correct)

1

Which copper splicing method allows the conductors to be folded into the splice and allows for maintenance, rearrangement and transfer of the conductors

1

What is the minimum bend radius of a 4 pair balanced twisted pair cord

1

What is the minimum bend radius of a multipair cable

1

Cable pair twists for CAT3 must be maintained to within ____________ of termination

1

Cable pair twists for CAT5e or higher must be maintained to within ____________ of termination

1

110 blocks come in increments of ________ pairs (select all correct)

1

BIX blocks come in increments of ________ pairs (select all correct)

1

Field terminated patch cables are not recommended for CAT5e

1

What is the most common video connector in the industry

1

Specification and visual inspection is what phase of testing

1

Testing with various test equipment is what phase of testing

1

Documentation is what phase of testing

1

Except in particular cases, what is the maximum length of equipment cords

1

A consolidation point will extend the horizontal cabling length

1

What is the maximum amount of work areas that a MUTOA should serve

1

A minimum of 1 dedicated, non-switched duplex receptacle should be available for equipment in each _________

1

What is the maximum square footage a TE should serve

1

What is minimum recommended cable tray width for an ER, TR or EF

1

Which grade of plywood has knotholes without any repair

1

Which grade of plywood contains some blemishes and the occasional knothole

1

Which grade of plywood has the knotholes cut out and replaced with a patch of clean wood

1

Which grade of plywood is the highest grade and is without any surface blemishes

1

Which grade of plywood should be used for ER, TR & EFs

1

How many walls should have plywood installed

1

Select all that apply to backboards in ERs, TRs & EFs

1

Most ITS installations will require a 19 inch by 7 ft rack

1

What are the common depths of racks (select all correct)

1

What are the popular thread sizes for racks/cabinets (select all correct)

1

What is the preferred size of patch panels

1

What are the reasons that FMT is not recommended (select all correct)

1

If using FMT, what rules must be followed (select all correct)

1

How many 90 degree bends are allowed in conduit segment

1

If more than two 90 degree bends are needed, what must be done (select all correct)

1

When conduits enter a TR through the floor, how far should they protrude

1

What are the 3 common depths of basket tray (rod stock tray) (select all correct)

1

This is the portion of the data center that actually houses the IT equipment

1

Which types of cables are recognized in data center telecommunications (select all correct)

1

Which two types of coaxial cable does ANSI/TIA 942 recognize for E1, E3 & T3 circuits (select all correct)

1

Which type of connectors are installed on 734-type and 735-type coaxial cable for E1, E3 & T3 circuits (select all correct)

1

Cable trays in data centers should be planned for initial maximum calculated fill ratio of ________%

1

How much clearance should be provided above the of cable trays when they are installed above cabinets

1

How much clearance should be above a cable tray that is installed below a raised floor

1

Cable trays installed under raised floors in data centers should be installed in the cold aisle

1

In a data center, how much horizontal cable management should be provided for each 1u of patch panel

1

Power strips supporting only single-corded equipment should be loaded no more than _______% of circuit capacity

1

Power strips supporting only dual-corded equipment should be loaded no more than _______% of circuit capacity

1

Some unique aspects of health care regarding access control are (select all correct)

1

In a health care facility, PT (pneumatic tube) system is typically what size tubing

1

Central equipment cabinets are the heart of the system and likely will occupy 4ft x 8ft of wall space in the TR

1

HEPA/ultra-low penetration air (ULPA) vacuum cleaners shall trap _________% of particles 0.12 micrometers and larger

1

In health care facility projects, the safety officer or facilities director shall make at least _________ documented visit(s) per week to each construction work zone

1

This document is the understanding between the customer and the contractor

1

CLA Series System Drawings: Campus or Site Plans

1

CLA Series System Drawings: Layout of complete building per floor

1

CLA Series System Drawings: Serving Zones: drop locations and cable IDs

1

CLA Series System Drawings: Communication equipment rooms

1

CLA Series System Drawings: Typical detail drawings: face-plate labeling, firestopping

1

CLA Series System Drawings: Schedules

1

What are the 3 major areas in security that may be part of an ITS installer's work (select 3)

1

A fire alarm system should be designed by a licensed fire protection engineer to ensure proper coverage and code compliance

1

DAS consists of an infrastructure of electronic devices including (select all correct)

1

This is a device that transmits and receives electromagnetic waves

1

Each 6dB increase in an antenna equals the ___________ of the possible range

1

Each 6dB decrease in an antenna equals the ___________ of the possible antenna range

1

The standoffs for a radiating cable need to be _______ inches below the cable tray

1

Wireless access points should be mounted at least ________ meter(s) from any metal obstructions

1

Most antennas used with APs indoors come with a ______ cable, commonly known as a pigtail

1

What are the 3 common voltages used in centrally amplified systems (select 3)

1

Which paging system operates at 24vdc

1

Which paging system will typically have 2 conductor cable installed

1

What are the 2 common types of sound masking systems (select 2)

1

What time each day does the master clock send a longer pulse that corrects all of the secondary clocks to the correct hour

1

D-loading coils are commonly placed by telephone companies at which distance

1