c09

1

For proper air temperature control in an air conditioning system using chilled water circulation, which condition should remain constant regardless of load changes ______.

1

Before doing any work on a hydraulic system equipped with accumulators, you should_______.

1

The first step when beginning to set the slide valves on a duplex reciprocating pump is to_________.

1

To safely remove the piston rod packing from the steam end of a reciprocating pump, you should_________.

1

In order to properly remove air from the casing of a centrifugal pump when starting, the pump should have a ______.

1

When fire safe or fire resistant fluid is to be used in a hydraulic system, it is important that _______.

1

To properly remove packing from a valve stuffing box, you should use a ________.

1

When replacing ball bearings on an electric motor shaft, you should ________.

1

To remove a hand held right-handed straight cut reamer after it has gone all the way through a hole, you should _____.

1

An acetylene pressure regulator should never be adjusted to maintain pressures exceeding (15psig) 103.4 kPa because_____.

1

When securing a flash-type evaporator for an extended period of time, you should______.

1

Why should a person performing maintenance on an air compressor wire and tag the system valves closed?

1

Which of the following conditions can contribute to accidents?

1

Fire doors are released by a/an__________.

1

Which of the following is an example of biological hazards?
I. Exposure to high temperatures, too high levels of relative humidity
II. Zoonotic diseases
III. Fungal diseases

1

How can ergonomics improve health and safety to the work place?
I. reduces the potential for accidents
II. reduces the potential for injury and ill health
III. improves performance and productivity

1

Which of the following aspects that ergonomist should consider to assess the fit between person and their work?
I. the job being done and the demands on the worker
II. the equipment used
III. the senses, especially vision, hearing and touch

1

Which of the following is/are the typical ergonomics problems found in the workplace like display screen equipment?
I. The screen is poorly positioned - it is too high/low/close/far from the worker, or is offset to one side.
II. The mouse is placed too far away and requires stretching to use.
III. Chairs are properly adjusted to fit the person, forcing awkward and comfortable postures.

1

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________.
I. they are properly grounded
II. Eye shields and gloves are worn
III. Loose clothing and jewelry are not worn

1

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________.
I. inspect the hoses for cracks and other defects
II. Remove jewelry and loose clothing
III. Bleed air pressure from the lines before breaking the connections

1

Fire prevention during welding or burning aboard any vessel should include_______.
I. Posting a fire watch in the immediate area
II. Providing an extinguisher which is ready for immediate use
III. Requiring the fire watch to remain on post for an adequate cool down period after the completion of welding of burning

1

A fire and boat drill on a tank vessel shall, by regulation, include which of the following?
I. starting the fire pumps
II. Checking fireman's outfits and other personel resuce equipment
III. Checking relevant communications equipment

1

Regulations require gears, coupling, flywheels, and all rotating machinery capable of injuring personnel to be__________.

1

Why is it that a good housekeeping on a vessel prevents fires?

1

When working around deck machinery it is a good safety practice to avoid standing in a ‘bright’ of a rope because_________.

1

To safeguard the operator and other personnel working on or near a hoisting operation, which of the following precautions should be observed?

1

To prevent oily rags from spontaneously igniting, what should you do?

1

The knife edges and gaskets of watertight doors should be _________.

1

Before the seas get rough, it is good safety practice to_________.

1

When a ship is expected to encounter rough seas, it is a good safety practice to ____________.

1

Which of the following must be eliminated to prevent accidents?

1

You are replacing a section of heavy piping on deck and using a chain fall to lift the pipe. Which of the following precautions should be taken to prevent personal injury?

1

Which of the listed conditions can be considered as the single greatest cause of accidents?

1

Safety is dependent on orderliness and cleanliness. Order may be maintained by __________.

1

Which of the following actions is required to be carried out during a fire drill on board?

1

What do all portable electric tools require a ground connection?

1

Which of the following statements represents the FIRST precaution to be taken prior to working in any installed electrical component?

1

Which practices should be followed at all times when using an electric bench grinding machine?

1

Which practices should be followed at all times when using an electric grinding machine?

1

Approved buoyant work vests may be carried aboard tank vessels and shall be worn by crew members’ ____________.

1

When should you wear safety glasses aside from when using a hand portable grinder and scraping paint with a hand scraper?

1

Machinery driving fuel oil transfer and fuel oil service pumps must be fitted with a remote means of stopping the machinery. Where is its location?

1

What is the purpose of injury report?

1

What is an occupational injury?

1

Which of the following is an example of biological hazard
I. Exposure to high temperatures, too high levels of relative humidity
II. Zoonotic diseases
III. Fungal diseases

1

Which of the following is an example of biological hazards?
I. Exposure to raw vegetable and animal products which may cause allergic reaction
II. Risk of poisoning while tasting food ingredients and meals at various stages of cooking
III. Risk of communicable diseases transmitted by pests, vermin, rodents, insects

1

Which of the following aspects that ergonomist should consider to assess the fit between person and their work?
I. the job being done and the demands on the worker
II. the equipment used
III. the senses, especially vision, hearing and touch

1

Which of the following aspects that ergonomist should consider the psychological aspect of a person?

1

Which of the following aspects that ergonomist should consider the psychological aspect of a person?

1

How can ergonomics improve health and safety to the work place?
I. reduces the potential for accidents
II. reduces the potential for injury and ill health
III. improves performance and productivity"

1

Which of the following is/are the typical ergonomics problems found in the workplace like display screen equipment?
I. The screen is poorly positioned - it is too high/low/close/far from the worker, or is offset to one side.
II. The mouse is placed too far away and requires stretching to use.
III. Chairs are properly adjusted to fit the person, forcing awkward and comfortable postures.

1

What is Chapter VIII of STCW Code?

1

Which practices should be followed at all times when using an electric bench grinding machine

1

When a ship is expected to encounter rough seas, it is a good safety practice to ____________.

1

Safety is dependent on orderliness and cleanliness. Order may be maintained by __________.

1

For the protection of personnel, moving parts of rotating machinery are required to be fitted with ___________.

1

Which practices should be followed at all times when using an electric grinding machine?

1

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________.
I. they are properly grounded
II. Eye shields and gloves are worn
III. Loose clothing and jewelry are not worn

1

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________.
I. inspect the hoses for cracks and other defects
II. Remove jewelry and loose clothing
III. Bleed air pressure from the lines before breaking the connections

1

All portable electric tools should have a ground connection to prevent_________.

1

Safety glasses should be worn when_________.
I. using a hand portable grinder
II. Scraping paint with a hand scraper
III. Using a hammer and a chisel

1

Before disconnecting a joint in a pipeline, you should__________.

1

Which of the actions listed and instituted on your part will have the greatest lasting effect on the crew with respect to safety?

1

All watertight doors and watertight hatches on small passenger vessels of less than 100 gross tons required to be marked in letters __________.

1

According to the Regulations, all escape hatches and other emergency exits on small passenger vessels of less than 100 gross tons shall be marked on__________.

1

Regarding battery charging rooms, ventilation should be provided __________.

1

Which of the following statements represents the FIRST precaution to be taken prior to working in any installed electrical component?

1

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out?

1

Which of the following systems must be arranged so as to be energized by the final emergency power source as required by regulation?
I. at least one light in the steering gear room
II. Each power operated watertight door system
III. Each charging panel for temporary emergency batteries

1

Any abnormal condition or emergency occurring in the fireroom must be immediately reported to the _________.

1

Any abnormal condition or emergency that occurs in the engine room must be reported immediately to the __________.

1

Before any work is done on a burner in an automatically fired auxiliary boiler, you should always ___________.

1

Which of the following conditions can contribute to accidents?

1

Good housekeeping on a vessel prevents fires by __________.

1

Fire prevention during welding or burning aboard any vessel should include_______.
I. Posting a fire watch in the immediate area
II. Providing an extinguisher which is ready for immediate use
III. Requiring the fire watch to remain on post for an adequate cool down period after the completion of welding of burning

1

Fire doors are released by a/an__________.

1

Before the seas get rough, it is good safety practice to_________.

1

You are replacing a section of heavy piping on deck and using a chain fall to lift the pipe. Which of the following precautions should be taken to prevent personal injury?

1

What safety precautions should be observed by the crew while working around machinery in an engine room?
I. They should wear safety shoes
II. They should wear ear protection
III. They should not wear jewelry

1

TO safeguard the operator and other personnel working on or near a hoisting operation, which of the following precautions should be observed?

1

All exposed and dangerous areas machinery, such as gears and rotating parts, shall be properly protected with__________.

1

Regulations require gears, coupling, flywheels, and all rotating machinery capable of injuring personnel to be__________.

1

Which of the listed conditions can be considered as the single greatest cause of accidents?

1

accidents are considered as an ‘unexpected contract’ you will be able to perform a better job by observing which of the following practices?
I. Looking for unsafe practices
II. Inspecting for unsafe conditions
III. Analyzing jobs for safer methods

1

Which of the following must be eliminated to prevent accidents?

1

When working around deck machinery it is a good safety practice to avoid standing in a ‘bright’ of a rope because_________.

1

Who is responsible for reporting a casualty for a mobile offshore drilling unit?

1

Which of the following actions is required to be carried out during a fire drill on board?

1

Which of the following events shall be conducted during a fire and boat drill?

1

A fire and boat drill on a tank vessel shall, by regulation, include which of the following?
I. starting the fire pumps
II. Checking fireman's outfits and other personel resuce equipment
III. Checking relevant communications equipment

1

Approved buoyant work vests may be carried aboard tank vessels and shall be worn by crew members’ ____________.

competency Quiz on c09, created by mrk nthny on 15/08/2016.

c09

For proper air temperature control in an air conditioning system using chilled water circulation, which condition should remain constant regardless of load changes ______.

Before doing any work on a hydraulic system equipped with accumulators, you should_______.

The first step when beginning to set the slide valves on a duplex reciprocating pump is to_________.

To safely remove the piston rod packing from the steam end of a reciprocating pump, you should_________.

In order to properly remove air from the casing of a centrifugal pump when starting, the pump should have a ______.

When fire safe or fire resistant fluid is to be used in a hydraulic system, it is important that _______.

To properly remove packing from a valve stuffing box, you should use a ________.

When replacing ball bearings on an electric motor shaft, you should ________.

To remove a hand held right-handed straight cut reamer after it has gone all the way through a hole, you should _____.

An acetylene pressure regulator should never be adjusted to maintain pressures exceeding (15psig) 103.4 kPa because_____.

When securing a flash-type evaporator for an extended period of time, you should______.

Why should a person performing maintenance on an air compressor wire and tag the system valves closed?

Which of the following conditions can contribute to accidents?

Fire doors are released by a/an__________.

Which of the following is an example of biological hazards? I. Exposure to high temperatures, too high levels of relative humidity II. Zoonotic diseases III. Fungal diseases

How can ergonomics improve health and safety to the work place? I. reduces the potential for accidents II. reduces the potential for injury and ill health III. improves performance and productivity

Which of the following aspects that ergonomist should consider to assess the fit between person and their work? I. the job being done and the demands on the worker II. the equipment used III. the senses, especially vision, hearing and touch

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________. I. they are properly grounded II. Eye shields and gloves are worn III. Loose clothing and jewelry are not worn

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________. I. inspect the hoses for cracks and other defects II. Remove jewelry and loose clothing III. Bleed air pressure from the lines before breaking the connections

Which of the following is an example of biological hazards?
I. Exposure to high temperatures, too high levels of relative humidity
II. Zoonotic diseases
III. Fungal diseases

How can ergonomics improve health and safety to the work place?
I. reduces the potential for accidents
II. reduces the potential for injury and ill health
III. improves performance and productivity

Which of the following aspects that ergonomist should consider to assess the fit between person and their work?
I. the job being done and the demands on the worker
II. the equipment used
III. the senses, especially vision, hearing and touch

Some of the hazardous of working with electric power tools may be avoided if the operator insures that _________.
I. they are properly grounded
II. Eye shields and gloves are worn
III. Loose clothing and jewelry are not worn

Some of the hazards associated with air-operated power tools may be avoided if the operator would_________.
I. inspect the hoses for cracks and other defects
II. Remove jewelry and loose clothing
III. Bleed air pressure from the lines before breaking the connections

A fire and boat drill on a tank vessel shall, by regulation, include which of the following?
I. starting the fire pumps
II. Checking fireman's outfits and other personel resuce equipment
III. Checking relevant communications equipment