1.0 RF Fundamentals

1

What is a measure of the antenna’s focus.

1

Number of times a signal completes a cycle 1 second.

1

A signal rising from the center line, falls through the center line, and rises again to meet the center line.

1

The most commonly used frequency unit and is nothing other than one cycle per second.

1

What two main frequency ranges used for wireless LAN communication

1

Technique which uses specific numbers and is assigned to a specific frequency.

1

The frequency range needed to transmit a signal, used by a single channel or a single RF signal.

1

The signal is a measure of shift in time relative to the start of a cycle. Phase is normally measured in degrees, where 0 degrees is at the start of a cycle, and one complete cycle equals 360 degrees.

1

A measure of physical distance that a wave travels over one complete cycle.

1

The height from the top peak to the bottom peak of the signal’s waveform,

1

The strength of an RF signal is usually measured by its power, in ________.

1

Define Term - DRS.

1

Define Term - MCS

1

In a BSS, if you disable lower data rates

1

To provide robust wireless coverage to an ever-increasing area, you should:

1

The process of moving an association from one AP to the next, so that the wireless connection is maintained as the client moves.

1

You should lay the cells out, which the pattern is seamless, leaving no holes in coverage.

1

Alternating channels to avoid overlap is commonly

1

Needed to automatically determine the location of wireless devices.

1

Site survey tools can be grouped into three basic categories based on their installation base:

1

Three basic types of site survey that you can perform as you plan and deploy a wireless network:

1

Analyze the environment to select AP locations when no APs have been deployed yet;

1

What tool to detect and identify any sources of interference you might encounter in the wireless coverage area.

1

Which tools perform predictive site survey:

1

To measure the effects of any existing APs in an area,

1

AP is self-contained; it is equipped with both wired and wireless hardware so that the wireless client associations can be terminated onto a wired connection locally at the AP.

1

To help manage more and more autonomous APs as the wireless network grows, AP management function is pushed out of the enterprise and into the Internet cloud.

1

This logical plan used traffic used to control, configure, manage, and monitor the AP itself

1

This logical plan used end-user traffic passing through the AP.

1

In a split-MAC Architectures which of the following are management functions:

1

In a split-MAC Architectures which of the following are management functions:

1

LAP gets its name because the code image and the local intelligence are stripped down, or lightweight, compared to the traditional autonomous AP.

1

The management functions are usually performed on a access switch, Split-MAC Architectures

1

Tunneling protocol makes this all possible by encapsulating the data between the LAP and WLC within new IP packets.

1

Messages are authenticated, encrypted, and used for exchanges that are used to configure the LAP and manage its operation over port 5246.

1

Every LAP and WLC must also authenticate each other with digital certificates. An X.509 certificate is preinstalled in each device when it is purchased.

1

What is a band and number of channels for 2.4 GHz range?

1

The channel spacing is known as the

1

According to power measurements, which are absolute powers

1

The decibel (db) is a handy function used logartihms to compare absolute measurement.

1.1 Describe the propagation of radio waves 1.2 Interpret RF signal measurements 1.3 Explain the principles of RF mathematics 1.4 Describe Wi-Fi antenna characteristics

1.0 RF Fundamentals

1.0 RF Fundamentals

What is a measure of the antenna’s focus.

Number of times a signal completes a cycle 1 second.

A signal rising from the center line, falls through the center line, and rises again to meet the center line.

The most commonly used frequency unit and is nothing other than one cycle per second.

What two main frequency ranges used for wireless LAN communication

Technique which uses specific numbers and is assigned to a specific frequency.

The frequency range needed to transmit a signal, used by a single channel or a single RF signal.

The signal is a measure of shift in time relative to the start of a cycle. Phase is normally measured in degrees, where 0 degrees is at the start of a cycle, and one complete cycle equals 360 degrees.

A measure of physical distance that a wave travels over one complete cycle.

The height from the top peak to the bottom peak of the signal’s waveform,

The strength of an RF signal is usually measured by its power, in ________.

Define Term - DRS.

Define Term - MCS

In a BSS, if you disable lower data rates

To provide robust wireless coverage to an ever-increasing area, you should:

The process of moving an association from one AP to the next, so that the wireless connection is maintained as the client moves.

You should lay the cells out, which the pattern is seamless, leaving no holes in coverage.

Alternating channels to avoid overlap is commonly

Needed to automatically determine the location of wireless devices.