Questão 1
Questão
Which section of the CEC deals with installation of heating units
Responda
-
Section 12
-
Section 16
-
Section 46
-
Section 62
Questão 2
Responda
-
Heat energy required to raise the temperature of a litre of water 1F
-
Heat energy required to raise the temperature of a pound of water 1F
-
Heat energy required to raise the temperature of a pound of water 1C
-
Heat energy required to raise the temperature of a litre of water 1C
Questão 3
Questão
Heat transferred by electromagnetic wave motion by which we receive heat from the sun is through?
Responda
-
Conduction
-
Convection
-
Radiation
-
HVAC units
Questão 4
Questão
What is usually provided on the intake side of the fan in the return air system?
Responda
-
Supply plenum
-
Power supply filter
-
Filter
-
Flue or stack
Questão 5
Questão
A schematic diagram is used to
Questão 6
Questão
The function of the refrigeration cycle is to
Responda
-
Removes heat from low temperature body and delivers it to a high temperature body
-
Removes heat from a high temperature body and delivers it to a low temperature body
-
Rejects energy to low temperature body
-
None of the above
Questão 7
Questão
Which section of the CEC covers rules relating to disconnect switches for furnaces?
Responda
-
Section 12
-
Section 16
-
Section 28
-
Section 62
Questão 8
Questão
Which part of the HVAC system is responsible for compressing the Freon
Responda
-
Compressor
-
Condenser
-
Evaporator
-
TX valve
Questão 9
Questão
This type of compressor is completely sealed inside a metal housing and is not serviceable
Responda
-
Hermetic
-
Reciprocating
-
Scroll
-
Semi-hermetic
Questão 10
Questão
What substance is used in a heat cycle to transfer heat from one area, and remove it to another
Responda
-
Refrigerant
-
Neon
-
Vapor
-
Xenon
Questão 11
Questão
A conventional condenser unit requires a liquid refrigerant which is also called?
Responda
-
Freon
-
Hydrogen
-
Helium
-
Carbon dioxide
Questão 12
Questão
Which component pushes the hot gas to the finned condenser coil in the outdoor side of the air conditioner
Questão 13
Questão
Two different pressures exist in the refrigeration cycle. Two components that separate the high-pressure side from the low-pressure side are:
Questão 14
Questão
In the cooling mode, what component is located inside the building?
Questão 15
Questão
To go from cooling source in a heat pump, what is required?
Responda
-
TRX valve
-
4 way reversing valve
-
Double pole thermostat
-
A disconnect switch
Questão 16
Questão
The amount of heat added to the liquid to make it saturated and change states is called
Responda
-
Super heat
-
Heat energy
-
Latent heat
-
Transferred heat
Questão 17
Questão
Heat, that when added or removed, causes a change in temperature but not in state
Responda
-
Latent heat
-
Sensible heat
-
Low heat
-
Energy heat
Questão 18
Questão
Refrigerant lines are usually made from
Responda
-
Aluminum
-
Stainless steel
-
Copper
-
Either a or c
Questão 19
Questão
Which part of a cooling system absorbs heat from the air?
Responda
-
Condenser
-
Evaporator
-
Compressor
-
Accumulator
Questão 20
Questão
Why is it necessary to have a heating element in a heat pump?
Responda
-
To eliminate condenser freezing
-
To protect against high outside temperature
-
To protect against low outside temperature
-
To provide heat for the room
Questão 21
Questão
Which statement indicates an acceptable method of supplying power to a 65,000 BTU gas fired hot water furnace?
Responda
-
Supply furnace from basement lighting
-
Supply furnace from nearest receptacle
-
Supply furnace from smoke detector circuit
-
Supply from dedicated circuit
Questão 22
Questão
What describes heat transfer from one metal to another in a heating system?
Responda
-
Conduction
-
Radiation
-
Convection
-
Evaporator
Questão 23
Questão
What type of evaporator coil is used in a heat pump?
Responda
-
Fin tube
-
Helical tube
-
Plate tube
-
Air bay pass tube
Questão 24
Questão
What does a shop drawing show?
Questão 25
Questão
What if the minimum current rating for a disconnect serving a motor compressor?
Questão 26
Questão
A high limit control in a gas furnace control is switched with a fan limit control. What is the result?
Responda
-
The burner will not ignite
-
The fan will cycle on and off
-
The burner won’t turn off
-
The fan won’t run
Questão 27
Questão
Which calculation determines the size of the overload fuses for motor compressor appliances?