Copiar e Editar

Cisco 640-911 Exam

Descrição

Quiz sobre Cisco 640-911 Exam, criado por sirhulk1 em 11-01-2014.
sirhulk1
Quiz por sirhulk1, atualizado more than 1 year ago
sirhulk1
Criado por sirhulk1 quase 11 anos atrás
355
0
0

Resumo de Recurso

Questão 1

Questão
Which two networking devices operate at Layer 1 of the OSI Layer (Choose two)
Responda
  • Repeater
  • Bridge
  • Switch
  • Router
  • Hub

Questão 2

Questão
Which two networking devices forward data based on destination MAC address?
Responda
  • Repeater
  • Bridge
  • Switch
  • Router
  • Hub

Questão 3

Questão
Which two network topologies are the most popular in switching? (Choose two)
Responda
  • Bus
  • Token Passing Bus
  • Star
  • Extended Star
  • Ring

Questão 4

Questão
Which device would you select to partition a network into VLANs
Responda
  • Repeater
  • Bridge
  • Switch
  • Router
  • Hub

Questão 5

Questão
At which layer of the OSI model does TCP operate?
Responda
  • Layer 1
  • Layer 2
  • Layer 3
  • Layer 4
  • Layer 5

Questão 6

Questão
Which two layers of the OSI model relate to the transmission of bits over the wire and packet forwarding based on destination IP address? (Choose two)
Responda
  • Layer 1
  • Layer 2
  • Layer 3
  • Layer 4
  • Layer 5

Questão 7

Questão
Which layer of the OSI model is associated with the reliable transmission of datagrams?
Responda
  • Datagram
  • Routing
  • Network
  • Data Link
  • Transport
  • Transmission
  • Session

Questão 8

Questão
Which three terms are used to describe data at Layers 1, 2, and 4 of the OSI Model?
Responda
  • PDUs
  • Bits
  • Sequences
  • Segments
  • Packets
  • Frames

Questão 9

Questão
Which two layers of the OSI model are combined in the Internet protocol suite Application Layer? (Choose two)
Responda
  • Layer 2
  • Layer 3
  • Layer 4
  • Layer 5
  • Layer 6

Questão 10

Questão
In an IEEE 802.3 frame, what is the significance of the DSAP field?
Responda
  • The DSAP field specifies the TCP or UDP port that is associated with the transport protocol.
  • The DSAP field is only used in the United States Department of Defense.
  • The DSAP field is only used in Ethernet II frames.
  • The DSAP field indicates the network layer protocol.

Questão 11

Questão
Which field in an Ethernet II frame performs the same function as the DSAP field in an 802.3 Ethernet frame?
Responda
  • Start of the frame
  • Ether-type
  • Frame Check Sequence (FCS)
  • Subnetwork Access Protocol
  • Logical Link Control

Questão 12

Questão
What are two features of a bridge? (Choose two)
Responda
  • Reliable transmission
  • Operate at Layer 2
  • Operate at Layer 3
  • Create multiple broadcast domains
  • Create multiple collision domains
  • Flood input packets to all ports
  • Drop IP packets with invalid destination ports

Questão 13

Questão
Which two layers of the OSI model are combined in the Internet protocol suite network access layer?
Responda
  • Layer 1
  • Layer 2
  • Layers 3
  • Layer 4
  • Layer 5
  • Layer 6
  • Layer 7

Questão 14

Questão
What are three reasons that switches supersede bridges? (Choose three)
Responda
  • Smaller frame buffers decrease latency
  • Forward, filter, or flood frames
  • Multiple simultaneous communications between ports
  • Larger inspection engine allows for higher throughput
  • Switches have many ports

Questão 15

Questão
Which action does a switch take if the destination MAC address is unknown?
Responda
  • Discard frame
  • Send ICMP unreachable message to source
  • Flood packet on all ports
  • Compare destination IP address against an ACL to determine if it is permitted
  • Send gratuitous ARP on all ports and wait for reply before forwarding.

Questão 16

Questão
Which statement describes the purpose of the MAC address forwarding table of a switch?
Responda
  • The switch consults the forwarding table to determine the best route to a destination.
  • The switch consults the forwarding table to determine the output port.
  • The switch consults the forwarding table to determine if the packet is routable.
  • The switch consults the forwarding table to determine if access control permits the packet.

Questão 17

Questão
What are two attributes of a VLAN?
Responda
  • A VLAN defines a collision domain.
  • A VLAN defines a broadcast domain.
  • Broadcast are flooded to all VLANs.
  • Collision are flooded to all VLANs.
  • A Layer 3 device is required to route packets between VLANs.
  • A Layer 2 device is required to route packets between VLANs.

Questão 18

Questão
Which four statements indicate unique properties of VLAN 1 on Cisco Nexus switches? (Choose four)
Responda
  • VLAN 1 is used to flood multicast traffic
  • VLAN 1 cannot be deleted.
  • VLAN 1 is used for Cisco Discovery Protocol.
  • VLAN 1 is used for VTP advertisements.
  • VLAN 1 defines a collision domain.
  • VLAN 1 defines a broadcast domain.

Questão 19

Questão
Which command displays the Trunking Native Mode VLAN on port Ethernet 1/18?
Responda
  • show running-config switchport e1/18
  • show running-config e1/18 switchport
  • show interface e1/18
  • show interface e1/18 switchport
  • show interface e1/18 native

Questão 20

Questão
Which VTP mode disallows the creation of local VLANs?
Responda
  • transparent
  • tunneling
  • server
  • client
  • off
  • native

Questão 21

Questão
Which three statements are true concerning RFC 1918 IP addresses (Choose three)
Responda
  • They are globally routable.
  • They are not globally routable.
  • They must not be filtered at the Internet border interfaces
  • They should be filtered at the internet border interfaces
  • They include 10.0.0.0/8, 172.16.0.0/16, 192.168.1.0/24
  • They include 10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16

Questão 22

Questão
Which two statements describe the purpose of RFC 1918? (Choose two)
Responda
  • Establish a range of IP addresses that are dedicated to the growing use of multicast video.
  • Establish a range if IP addresses that are dedicated to the growing use of peer to peer file-sharing applications.
  • Establish a range of IP addresses that are dedicated to use on internal networks
  • Establish a range of IP addresses to address the shrinking pool of globally routable addresses.

Questão 23

Questão
What three reasons to migrate from IPv4 to IPv6? (Choose three)
Responda
  • IPv6 eliminates the requirement for NAT
  • IPv6 includes enough IP addresses to allocate more than four billion IP addresses to every person on earth.
  • IPv6 eliminates the need for VLANs
  • Hosts can be assigned an IP address without DHCP
  • Hosts can be assigned an IP address without DNS.

Questão 24

Questão
Which two options describe services that are provided by TCP? (Choose two)
Responda
  • Session multiplexing
  • Ether Types identify destination services
  • Connection-oriented
  • best-effort packet delivery
  • binary translation.

Questão 25

Questão
Which two options describe services that are provided by UDP ? (Choose two)
Responda
  • Session multiplexing
  • Segmentation
  • Connection-oriented
  • best-effort packet delivery

Questão 26

Questão
Which two options represent a subnet mask that allows for a maximum of 14 available host addresses on a subnet? (Choose two)
Responda
  • 255.255.255.240
  • 255.255.255.192
  • 255.255.240.0
  • 255.255.192.0
  • /14
  • /21
  • /26
  • /28

Questão 27

Questão
What is the binary value of the hexadecimal number 0x511
Responda
  • 10100011001
  • 10101010101
  • 10110010001
  • 10100010001
  • 10100110011

Questão 28

Questão
What is the binary value of the decimal number 1263
Responda
  • 11011101101
  • 10011101111
  • 10011101011
  • 1101000111
  • 1011110111

Questão 29

Questão
Which option is an example of an advanced distance vector routing protocol?
Responda
  • EIGRP
  • RIP
  • OSPF
  • ARP

Questão 30

Questão
Which option is an example of a distance vector routing protocol?
Responda
  • RIP
  • OSPF
  • ARP
  • IS-IS

Questão 31

Questão
Which option is an example of a link-state protocol
Responda
  • EIGRP
  • RIP
  • OSPF
  • ARP

Questão 32

Questão
What is the maximum allowable hop count for RIPv1?
Responda
  • 4
  • 8
  • 12
  • 15
  • 16

Questão 33

Questão
What is the default periodic interval at Ribv1 sends routing updates?
Responda
  • 15 seconds
  • 30 seconds
  • 45 seconds
  • 60 seconds
  • 90 seconds
  • RIPv1 only sends routing updates when the topology changes

Questão 34

Questão
What does RIPv1 send to its neighbors?
Responda
  • Information about changed routes
  • information about new routes
  • The entire routing table.
  • Information about deleted routes.

Questão 35

Questão
What are two advantages of employing an external router for inter-vlan routing over an IEEE 802.1Q trunk link? (Choose two)
Responda
  • Layer 3 functionality is not required on the switch
  • The router facilities communication between VLANs.
  • The single traffic path is optimized.
  • Latency is reduced as packets leave the switch.
  • Equal-Cost Multipath is supported.

Questão 36

Questão
Which statement correctly describes an SVI?
Responda
  • An SVI is a Layer 2 interface and uses a dynamic MAC address.
  • An SVI cannot have an IP address assigned to it.
  • An SVI provides Layer 3 routing between VLANs.
  • Each switch port requires an SVI assignment.

Questão 37

Questão
What is the Cisco Nexus Operating system command to define a port as a layer 3
Responda
  • switchport
  • no switchport
  • l3 switchport
  • port switching off

Questão 38

Questão
Which statement is correct regarding a routed port on a multilayer switch?
Responda
  • A routed port requires a SVI definition.
  • Routed ports cannot be configured on a multilayer switch that uses SVIs.
  • A maximum of 32 routed ports can be provisioned on a given multilayer switch.
  • A routed port is a physical port that supports layer 3 routing

Questão 39

Questão
On a new Cisco Nexus switch, you receive an error message when you attempt to create an SVI. What is the first command you must use to create the SVI?
Responda
  • interface vlan (vlan_id)
  • vlan (vlan_id)
  • feature svi
  • interface routed
  • feature inter-vlan

Questão 40

Questão
Which command should you use to configure a Cisco Nexus switch certificationort for Layer 2 operation?
Responda
  • nexus(config-if)#switchport
  • network(config-if)# layer-2
  • nexus(config-if)# routed
  • nexus(config-if)#interface-vlan

Questão 41

Questão
What are two core features of Cisco Nexus Operating system (Choose two)
Responda
  • SNMPv3
  • RMON
  • System Manager
  • PSS
  • VRF
  • TRILL

Questão 42

Questão
What is the acronym expansion of the UDLD feature of Cisco Nexus Operating System?
Responda
  • UniDirectional Link Detection
  • Unified Data Link Distribution
  • Unified Data Loss Detection
  • Unified Directional Link Distribution
  • Unidirectional Data Loss Detection.

Questão 43

Questão
What are four security features that are included in Cisco Nexus Operating system
Responda
  • Cisco TrustSec
  • IEEE 802.1Qau
  • CoPP
  • port security
  • PIM
  • SSL VPN
  • IPSec VPN
  • ACLs

Questão 44

Questão
What are three modular layer 2 processes in Cisco Nexus Operating system?
Responda
  • UDLD
  • PIM
  • HSRP
  • STP
  • Cisco Discovery Protocol (CDP)
  • OSPF

Questão 45

Questão
What are three modular layer 3 processes in Cisco Nexus Operating system?
Responda
  • UDLD
  • PIM
  • HSRP
  • STP
  • Cisco Discovery Protocol
  • OSPF

Questão 46

Questão
What are four security features that arae included in Cisco Nexus Operating System?
Responda
  • Cisco TrustSec
  • CoPP
  • ACLs
  • Port Security
  • IPsec VPN

Questão 47

Questão
What are two default user roles in Cisco Operating System?
Responda
  • admin
  • Network Operator
  • Operator
  • Storage Operator
  • Root
  • System Manager

Questão 48

Questão
On most keyboards, the up arrow and down arrow keys move through the command history. Which two key sequences can be used as alternative
Responda
  • ALT+A
  • ALT+F
  • ALT+N
  • ALT+E
  • ALT+P

Questão 49

Questão
What is the function of the Tab key on the Cisco Nexus Operating System command line interface?
Responda
  • Redisplays the current command line.
  • deletes all characters from the cursor to the end of the command line.
  • Clears the terminal screen
  • completes a partially entered command if enough characters are present.
  • moves the cursor one word to the right

Questão 50

Questão
where does Cisco Nexus Operating system store the running configuration file.
Responda
  • RAM
  • Flash
  • bootflash
  • Volatile
  • NVRAM

Questão 51

Questão
Where does Cisco Nexus Operating system store the startup configuration file?
Responda
  • RAM
  • flash
  • bootflash
  • volatile
  • NVRAM

Questão 52

Questão
Which two commands would you use to erase the Cisco Operating System configuration and return the switch to factory defaults?
Responda
  • write erase boot
  • erase configuration
  • erase running--configuration
  • erase startup-configuration
  • reboot
  • reload
  • shutdown

Questão 53

Questão
What is the minimum required command to enter global configuration mode on a Cisco Nexus switch?
Responda
  • con
  • configure
  • configure global
  • configure terminal

Questão 54

Questão
Which option would you use to exit the Cisco Nexus Operating System interface configuration mode and return to the exec prompt?
Responda
  • Ctrl-C
  • Ctrl-Z
  • Ctrl-E
  • exit

Questão 55

Questão
What is the correct format of an access control list on a Cisco Nexus switch to deny unencrypted. Web traffic from any source to destination host 10.10.1.110?
Responda
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp any host 10.10.1.110 eq 80
  • switch(config)# deny tcp any host 10.10.1.110 eq 80
  • switch(config)# access-list 101 deny tcp any host 10.10.1.110 eq 80 switch(config)# access-list 101 permit ip any any
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp any host 10.10.1.110 eq 80 switch(config)# access-list 101 permit ip any any

Questão 56

Questão
What is the correct format of an access control list on a Cisco Nexus switch to deny hosts on the 172.16.1.0/21 network from accessing HTTP proxy servers listening on port 8080?
Responda
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp 172.16.1.0 0.0.7.255 any eq 8080 switch(config-acl)# permit ip any any
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp any 172.16.1.0 255.255.248.0 eq 8080 switch(config-acl)# permit ip any any
  • switch(config)# access-list 101 deny tcp 172.16.1.0 0.0.15.255 eq 8080
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp any host 172.16.1.0/21 eq 8080
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp any host 10.10.1.110 eq 21 switch(config-acl)# permit ip any any

Questão 57

Questão
What is the correct format of an access control list on a Cisco Nexus switch to deny hosts on the 172.16.1.0/21 network from accessing HTTP proxy servers listening on port 8080?
Responda
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp 172.16.1.0 0.0.7.255 any eq 8080 switch(config-acl)# permit ip any any
  • switch(config)# ip access-list 101 switch(config-acl)# deny tcp 172.16.1.255.255.248.0 any eq 8080 switch(config-acl)# permit ip any any
  • switch(config)# access-list 101 deny tcp 172.16.1.0 0.0.15.255 eq 8080
  • switch(conifg)# ip access-list 101 switch(config-acl)# deny tcp any host 172.16.1.0/21 eq 8080

Questão 58

Questão
What is the correct format of an access control list on a Cisco Nexus switch to only permit unencrypted web traffic from the 172.16.1.0./25 network to destination host 10.10.1.110?
Responda
  • switch(config)# ip access-list 101 switch(config-acl)# permit tcp host 172.16.1.0/25 any eq 80
  • switch(config)# ip access-list 101 switch(config-acl)# permit tcp 172.16.1.0 255.255.255.128 any eq 80
  • switch(config)# ip access-list 101 switch(config-acl)# permit tcp 172.16.1.0/25 any eq 80
  • switch(config)#access-list 101 permit tcp 172.16.1.0/25 0.0.0.128 eq 80
  • switch(conifg)# ip access-list 101 switch(config-acl)# permit tcp any 172.16.1.0 255.255.248.0 eq 80

Questão 59

Questão
which device forwards data based on the destination IP address?
Responda
  • Repeater
  • bridge
  • switch
  • router
  • hub

Questão 60

Questão
Which network topology is most closely associated with classical CSMA/CD?
Responda
  • bus
  • token passing bus
  • star
  • Extended star
  • ring

Questão 61

Questão
Which network topology is most closely associated with FDDI
Responda
  • bus
  • token passing bus
  • star
  • extended star
  • ring

Questão 62

Questão
Which layer of the OSI model is associated with Token Ring Media Access Control
Responda
  • datagram
  • routing
  • network
  • data link
  • transport
  • transmission
  • session

Questão 63

Questão
When deploying 10BASE-2 Ethernet which type of connector is used
Responda
  • AUI
  • UTP
  • STP
  • BNC
  • RJ-11
  • RJ-45
  • ST
  • DC

Questão 64

Questão
When deploying 10BASE-2 Ethernet, what is the maximum cable length?
Responda
  • 100 meters
  • 100 Feet
  • 150 meters
  • 150 feet
  • 185 meters
  • 185 feet

Questão 65

Questão
How many IP address ranges are specified in RFC 1918
Responda
  • 1 in Class A, 2 in Class B, and 4 in Class C
  • 2 in Class A, 4 in Class B, and 8 in Class C
  • 4 in Class A, 8 in Class B, and 16 in Class C
  • 1 in Class A, 16 in Class B, and 256 in Class C

Questão 66

Questão
What is required to allow devices that are using RFC 1918 addresses to communicate over the Internet?
Responda
  • A private to public VLAN ust be defined on the Internet border device
  • The Internet firewall must permit RFC 1918 addresses.
  • VLAN translation is required on the Internet border device.
  • Network address translation is required on the Internet border device.

Questão 67

Questão
What is the addressing format of IPv6?
Responda
  • 48-bit dotted decimal
  • 48-bit colon-delimited hexadecimal
  • 64-bit colon-delimited hexadecimal.
  • 128-bit dotted decimal
  • 128-bit colon-delimited hexadecimal

Questão 68

Questão
Which statement describes the function of the OSI transport layer?
Responda
  • It segments data from the system of the sending host and reassembles the data into a data stream on the system of the receiving host.
  • It provides the connectivity and path selection between two host systems that may be located on geographically separated networks.
  • It defines how data is formatted for transmission and how access to the physical media is controlled.
  • It establishes, manages, and terminates session between two communicating hosts.

Questão 69

Questão
Which transport protocol requires a three-way handshake to establish a new connection?
Responda
  • ARP
  • UDP
  • IP
  • TCP

Questão 70

Questão
What is the subnet mask for the network 172.16.0.0/21?
Responda
  • 255.255.0.0
  • 255.255.255.240
  • 255.255.248.0
  • 255.255.255.248
  • 255.255.248.240
  • 255.255.255.0

Questão 71

Questão
What is the dotted hexadecimal representation of the IP address 172.13.99.225
Responda
  • AC.0D.63.E1
  • AB.63.99.D5
  • E2.1D.E1.66
  • BC.0C.C3.1F
  • CC.0D.F3.21

Questão 72

Questão
What is the decimal value of the hexadecimal number of 0x718?
Responda
  • 718
  • 1816
  • 2907
  • 3511

Quer criar seus próprios Quizzes gratuitos com a GoConqr? Saiba mais.

Semelhante

Português - 3 - Ortografia e acentuação
glenerdourado
Aprenda a fazer uma boa Redação em 5 passos
Alessandra S.
Direito Civil
nt31.1
Curiosidades do Mundo: Fatos da História
Alessandra S.
Phrasal Verbs - Inglês #1
Eduardo .
Literatura
neusamiotto
A U T A R Q U I A
Jean Pierre Silva
Curiosidades da culinária
Casa e Jardim
Respiração aeróbia - 10º ano
hlopes047
Números e Operações (Fundamental)
Andre Gonçalves
Memória Computacional
Filipe Gabriel
Explore a Biblioteca