Copiar e Editar

CCNA (200-120) / 60questions 60minuts / EN

Descrição

CCNA 200-120 CCNA 5.0 (CCNA 5.0 EN) Quiz sobre CCNA (200-120) / 60questions 60minuts / EN, criado por Almery M. em 16-03-2016.
Almery M.
Quiz por Almery M., atualizado more than 1 year ago
Almery M.
Criado por Almery M. mais de 8 anos atrás
35
1
0

Resumo de Recurso

Questão 1

Questão
How should you power up a Cisco router?
Responda
  • Press the Reset button.
  • Turn the power switch to “on.”
  • Connect the fiber cable to another router.
  • Attach the power cable plug to the router power supply socket.

Questão 2

Questão
How do you instruct a Cisco device to parse and execute an entered command?
Responda
  • Press the Send key
  • Press the Enter key
  • Add a space at end of the command
  • Wait 5 seconds after you enter the command

Questão 3

Questão
Which Cisco router component is used primarily to store the startup-config file?
Responda
  • RAM
  • ROM
  • NVRAM
  • Flash memory
  • Configuration register

Questão 4

Questão
If a route for a network is in holddown and an update arrives from a neighboring router with the same metric as was originally recorded for the network, what does the router do?
Responda
  • Ignores the update
  • Increments the holddown timer
  • Marks the network as “accessible” and removes the holddown timer
  • Marks the network as “accessible” but keeps the holddown timer on

Questão 5

Questão
How could you obtain CDP information about a remote device that is not directly connected?
Responda
  • Use the command show cdp neighbors’ address.
  • Use the command show cdp neighbors’ hostname.
  • Use SSH or Telnet to access a Cisco device connected to the target device.
  • It is not possible to obtain CDP information about a remote device.

Questão 6

Questão
Which address type from IPv4 was eliminated in IPv6?
Responda
  • Unicast
  • Multicast
  • Broadcast
  • Everycast

Questão 7

Questão
Set of networks subject to translation using NAT.
Responda
  • Static NAT
  • Dynamic NAT
  • Inside network
  • Outside global IP address

Questão 8

Questão
If a router does not match the appropriate address portions to a number on its routing table, it [blank_start].[blank_end]
Responda
  • sends the packet back to the sender.
  • passes the packet to the next router in.
  • adds that number to its table.
  • discards the packet.

Questão 9

Questão
How many subnets are gained by subnetting 172.17.32.0/20 into multiple /28 subnets?
Responda
  • 16
  • 32
  • 256
  • 1024

Questão 10

Questão
Which of the following describes the DHCP server provided by Cisco IOS?
Responda
  • It is a full DHCP server
  • Its support is limited to assigning IP addresses to clients.
  • It has to get is DHCP information for a master DHCP server.
  • It has limited DHCP support and can only assign IP addresses and default gateways to clients.

Questão 11

Questão
How can you most effectively summarize the IP range of addresses from 172.168.12.0/24 through 172.168.13.0/24?
Responda
  • 172.168.12.0/23
  • 172.168.12.0/22
  • 172.168.12.0/21
  • 172.168.12.0/20

Questão 12

Questão
A subnet mask tells the router to look at which portions of an IP address?
Responda
  • Mask and host bits
  • Host and network bits
  • Host and subnet bits
  • Network and subnet bits

Questão 13

Questão
If a route for a network is in holddown and an update arrives from a neighboring router with the same metric as was originally recorded for the network, what does the router do?
Responda
  • Ignores the update
  • Increments the holddown timer
  • Marks the network as “accessible” and removes the holddown timer
  • Marks the network as “accessible” but keeps the holddown timer on

Questão 14

Questão
What is the decimal equivalent of the binary number 11000111?
Responda
  • 218
  • 199
  • 179
  • 208

Questão 15

Questão
What does split horizon specify?
Responda
  • That information about a route should not be sent in any direction
  • That information about a route should not be sent back in the direction that the original information came from
  • That information about a route should always be sent back in the direction that the original information came from
  • That information about a route should be sent back only in the direction that the original information came from

Questão 16

Questão
The binary number 11101000111 converted into a decimal number, using powers of 2, is [blank_start].[blank_end]
Responda
  • 1183.
  • 1873.
  • 1638.
  • 1863.

Questão 17

Questão
In which situation is an administrative distance required?
Responda
  • whenever static routes are defined
  • whenever dynamic routing is enabled
  • when the same route is learned via multiple routing sources
  • when multiple paths are available to the same destination and they are all learned via the same routing protocol

Questão 18

Questão
What is the RSTP equivalent to the STP listening state?
Responda
  • Blocking
  • Listening
  • Discarding
  • Forwarding

Questão 19

Questão
Which statement is true of a port in the listening state?
Responda
  • The port is able to check for BPDUs and populate the MAC table.
  • The port is able to check for BPDUs, but not yet populate its MAC table.
  • The port is able to populate its MAC table, but not yet forward user frames.
  • The port is able to forward user frames, but not yet populate its MAC table.

Questão 20

Questão
Which of the following is a customized text that is displayed before the username and password login prompts?
Responda
  • Message Of the Day
  • Login banner
  • User banner
  • Warning message

Questão 21

Questão
With RSTP, which two port roles are included in the active topology?
Responda
  • Root and alternate
  • Root and designated
  • Alternate and backup
  • Designated and backup

Questão 22

Questão
Which term commonly describes the endless flooding or looping of frames?
Responda
  • Flood storm
  • Loop overload
  • Broadcast storm
  • Broadcast overload

Questão 23

Questão
Regarding STP, what is the state of a nondesignated port?
Responda
  • Blocking
  • Learning
  • Listening
  • Forwarding

Questão 24

Questão
Which of the following is the most secure method of remotely accessing a network device?
Responda
  • http
  • telnet
  • ssh
  • rmon
  • snmp

Questão 25

Questão
When you use the show interface command to display the status and statistics for the interfaces configured on a Catalyst switch, which output field indicates the MAC address that identifies the interface hardware?
Responda
  • MTU 1500 bytes
  • Hardware is … 10BaseT
  • Address is 0050.BD73.E2C1
  • 802.1d STP State: Forwarding

Questão 26

Questão
Which term describes multiple copies of a frame arriving on different ports of a switch?
Responda
  • Flood storm
  • Multiple frame transmission
  • MAC database instability
  • Loop overload

Questão 27

Questão
Which show command requires that you have privileged EXEC mode access?
Responda
  • show ip
  • show version
  • show running
  • show interfaces

Questão 28

Questão
What are TWO major benefits of adding a bridge to a network?
Responda
  • Isolating potential network problems to specific segments
  • Increasing the speed of a network
  • Extending a LAN to cover greater distances by joining multiple segments
  • Creating fewer collision domains
  • Forwarding data frames between LAN segments

Questão 29

Questão
When a single computer with one IP address has several websites open at once, this is called [blank_start].[blank_end]
Responda
  • windowing.
  • session multiplexing.
  • segmenting.
  • connection-oriented protocol.

Questão 30

Questão
If the POST tests complete successfully on a Catalyst switch, what display could you see on the console?
Responda
  • The > prompt
  • The privileged EXEC prompt
  • The Management Console logon screen
  • A list of commands available on the switch

Questão 31

Questão
Which information does the show vlan command display?
Responda
  • VTP domain parameters
  • VMPS server configuration parameters
  • Which ports are configured as trunks
  • Names of the VLANs and the ports assigned to the VLANs

Questão 32

Questão
What are TWO reasons for using 802.1Q?
Responda
  • To allow switches to share a trunk link with non-trunking clients
  • To allow clients to see the 802.1Q header
  • To provide inter-VLAN communications over a bridge
  • To load-balance traffic between parallel links using the Spanning Tree Protocol
  • To provide trunking between Cisco switches and other vendor switches

Questão 33

Questão
Which CLI prompt indicates that you are working in privileged EXEC mode?
Responda
  • hostname#
  • hostname>
  • hostname-exec>
  • hostname-config

Questão 34

Questão
What are the TWO most common IPv4-to-IPv6 transition techniques?
Responda
  • IPv6 NAT
  • dual stack
  • 6to4 tunnels
  • IPv6 mobile

Questão 35

Questão
Which TWO pieces of information are included in a CDP update packet?
Responda
  • platform
  • routing updates
  • device identifiers
  • MAC Address list
  • link speed

Questão 36

Questão
Which TWO statements are true regarding dual stack?
Responda
  • A new API replaces gethostbyname and gethostbyaddr calls.
  • Tunneling is automatic.
  • Dual stack prefers IPv4 over IPv6.
  • You cannot use IPv4 while converting to IPv6.
  • The stack to use is chosen based on destination address.

Questão 37

Questão
How can you most effectively summarize the IP range of addresses from 10.1.32.0 through 10.1.35.255?
Responda
  • 10.1.32.0/23
  • 10.1.32.0/22
  • 10.1.32.0/21
  • 10.1.32.0/20

Questão 38

Questão
How do you start a Catalyst 2950 series switch?
Responda
  • Press the on/off switch.
  • Power up the redundant power supply.
  • Connect a network cable to another switch on the network.
  • Attach the power cable plug to the switch power supply socket.

Questão 39

Questão
Which Cisco IOS command should you use to set the clock speed to 64 kbps on a serial interface on a Cisco router?
Responda
  • clock rate 64
  • clock speed 64
  • clock rate 64000
  • clock speed 64000

Questão 40

Questão
OSPF routes packets within a single [blank_start].[blank_end]
Responda
  • area.
  • network.
  • segment.
  • autonomous system.

Questão 41

Questão
Which Cisco IOS command creates a message to be displayed upon router login?
Responda
  • hostname hostname
  • banner motd message
  • hostname interface description
  • description interface description

Questão 42

Questão
Which Cisco IOS command is used to return to user EXEC mode from the privileged EXEC mode?
Responda
  • exit>
  • quit
  • disable
  • userexec

Questão 43

Questão
Which access level allows a person to access all router commands and can be password protected to allow only authorized individuals to access the router?
Responda
  • user EXEC level
  • setup EXEC level
  • enable EXEC level
  • privileged EXEC level

Questão 44

Questão
Which component of security ensures the data has not been tampered with?
Responda
  • Authentication
  • Integrity
  • Confidentiality
  • Anti-Playback

Questão 45

Questão
Which organization offers certification for interoperability between vendors of 802.11 products?
Responda
  • Wi-Fi
  • IEEE
  • EMA
  • WISC

Questão 46

Questão
Which THREE are the steps to secure a WLAN?
Responda
  • Encryption for providing privacy and confidentiality
  • Authentication to ensure that legitimate clients and users access the network via trusted access points
  • Controls transmit power to limit the AP access range to the property boundaries of the parent organization
  • Protection from security risks and availability with intrusion detection and intrusion protection systems for WLANs

Questão 47

Questão
What are THREE characteristics of Ethernet 802.3?
Responda
  • based on the CSMA/CD process
  • a standard that has been replaced by Ethernet II
  • specifies the physical layer (Layer 1)
  • developed in the mid-1970s
  • specifies the MAC portion of the data link layer (Layer 2)
  • also referred to as thick Ethernet

Questão 48

Questão
Which TWO of these addresses are private IP addresses?
Responda
  • 10.215.34.124
  • 127.16.71.43
  • 172.17.10.10
  • 225.200.15

Questão 49

Questão
How many bits are in an IPv4 address?
Responda
  • 16
  • 32
  • 48
  • 64
  • 128

Questão 50

Questão
Encapsulates the network layer packet in a frame.
Responda
  • Network layer
  • Datalink layer
  • Physical layer

Questão 51

Questão
Occurs when RF waves are soaked up by walls.
Responda
  • Absorption
  • Reflection
  • Scattering

Questão 52

Questão
How many bits are in an IPv6 address?
Responda
  • 16
  • 32
  • 48
  • 64
  • 128

Questão 53

Questão
Provides applications for file transfer, network troubleshooting, and Internet activities, and supports the network
Responda
  • Physical layer
  • Datalink layer
  • Internet layer
  • Transport layer
  • Application layer

Questão 54

Questão
Encodes the data-link frame into a pattern of 1s and 0s (bits) for transmission on the medium (usually a wire).
Responda
  • Network layer
  • Datalink layer
  • Physical layer

Questão 55

Questão
Which of the following four attacks are classified as access attacks? (choose one or more)
Responda
  • Password attacks
  • DDoS
  • Trojan horse
  • Love Bug

Questão 56

Questão
Which THREE statements about TCP are accurate?
Responda
  • TCP operates at Layer 3 of the TCP/IP stack.
  • TCP is a connection-oriented protocol.
  • TCP provides no error checking.
  • TCP packets are numbered and sequenced so that the destination can reorder packets and determine if a packet is missing.
  • TCP provides no recovery service.
  • Upon receipt of one or more TCP packets, the receiver returns an acknowledgement to the sender indicating that it received the packets.

Questão 57

Questão
What are TWO major benefits of adding a bridge to a network?
Responda
  • isolating potential network problems to specific segments
  • increasing the speed of a network
  • extending a LAN to cover greater distances by joining multiple segments
  • creating fewer collision domains.
  • forwarding data frames between LAN segments.

Questão 58

Questão
Indicates how well the network can accommodate more users or data transmission requirements.
Responda
  • Speed
  • Cost
  • Security
  • Availability
  • Scalability
  • Reliability
  • Topology

Questão 59

Questão
Which two statements about wireless networks are accurate?
Responda
  • Instead of cables, wireless communication uses RFs or infrared waves to transmit data.
  • To receive the signals from the access point, a computer needs to have a wireless adapter card or wireless NIC.
  • For wireless LANs, a key component is a router, which propagates signal distribution.
  • Wireless networks are not very common, and generally only large corporations use them.

Questão 60

Questão
What are TWO characteristics of OSPF?
Responda
  • hierarchical
  • proprietary
  • open standard
  • similar to RIP

Quer criar seus próprios Quizzes gratuitos com a GoConqr? Saiba mais.

Semelhante

CCNA (200-120) / 60questões 60minutos / PT-BR
Almery M.
CCNA - MODELO OSI
Rafael La Selva
Roteadores - Memorias - Armazenamento
Fabiana Claro
Camada de Rede/Network
Fabiana Claro
Tabela de Roteamento
Fabiana Claro
Roteadores - Interfaces
Fabiana Claro
ACL - Lista de Controle de Acesso
Fabiana Claro
SYSLOG
Fabiana Claro
EIGRP
Elton Roberto Rodrigues Simões
Palavras inglês CCNA
Igor Allen Ritzm
CCNA
Thiago PRATA
Explore a Biblioteca