Copy and Edit

CDC 2A652N - Volume 1 - Maintenance & Fundamentals

Description

CDC 2A652N - Volume 1 - Maintenance & Fundamentals
nicilynn1981
Quiz by nicilynn1981, updated more than 1 year ago
nicilynn1981
Created by nicilynn1981 about 9 years ago
36
1
0

Resource summary

Question 1

Question
Risk management principles should be applied to
Answer
  • Only duty-related activities to enhance the safety and well-being of yourself and others.
  • On- and off-duty activities to enhance the safety and well-being of yourself and others.
  • Only duty-related activities to protect yourself and other Airmen from imminent harm.
  • On- and off-duty activities to protect yourself and other Airmen from imminent harm.

Question 2

Question
What situation does not warrant prompt reporting to your supervisor?
Answer
  • Using personal protective equipment.
  • Unsafe working conditions.
  • Known pregnancies.
  • Personal injury.

Question 3

Question
Before removing a component from an air compressor, you must ensure
Answer
  • The air compressor is grounded.
  • The air strainer is in place.
  • The battery is disconnected.
  • All air pressure is drained.

Question 4

Question
Why should the frame of an electrical motor be grounded?
Answer
  • To prevent the energized windings from touching the frame.
  • To prevent current from following the path of least resistance.
  • To prevent you from receiving an electrical shock if the energized windings touch the frame.
  • To prevent current from flowing directly to ground if the energized windings touch the frame.

Question 5

Question
Which type of hammer should you use to avoid damaging driving materials?
Answer
  • Claw
  • Sledge
  • Soft face
  • Ball-peen

Question 6

Question
Which type of screwdriver has blades designed to lessen the possibility of the screwdriver slipping from the screw head?
Answer
  • Cross-point.
  • Flat-blade.
  • Cross-tip.
  • Offset

Question 7

Question
Which pliers should be used to hold odd-shaped objects?
Answer
  • Snap ring.
  • Diagonal cutting.
  • Multiple slip-joint.
  • Combination slip-joint

Question 8

Question
Which pliers have a locking device to hold materials securely?
Answer
  • Snap ring.
  • Vice grips.
  • Water pump.
  • Diagonal cutters.

Question 9

Question
Diagonal cutting pliers are designed to cut
Answer
  • Bolts
  • Rivets
  • Hard steel
  • Small wire

Question 10

Question
Before operating the pneumatic impact wrench, you must
Answer
  • Inspect it
  • Lubricate it
  • Blow out the air hose
  • Ensure that its use is necessary

Question 11

Question
Replacement hardware decisions on support equipment must be governed by
Answer
  • Supervisor's preference
  • Serviceablility criteria
  • Cosmetic appearance
  • Availability

Question 12

Question
What type of bolt is typically used to connect accessories to an engine?
Answer
  • Stud
  • Fine thread bolt
  • Coarse thread bolt
  • General purpose bolt

Question 13

Question
What type of nut should never be used in areas where the temperature exceeds 250 degrees Fahrenheit?
Answer
  • Nonmetallic self-locking nuts
  • Metallic self-locking nuts
  • Castellated nuts
  • Plain nuts

Question 14

Question
What color code is used on pre-insulated terminal lugs for wire sizes 18 through 22?
Answer
  • Red
  • Blue
  • Green
  • Yellow

Question 15

Question
What are the three different types of terminal lugs?
Answer
  • Red, Blue & Yellow
  • Straight, Right Angle & Flat
  • Copper, Aluminum & Plastic
  • Pre-insulated, uninsulated & reinsulated

Question 16

Question
What does the “-4” identify in fitting part number MS20822-4D?
Answer
  • Military specification
  • Type of fitting
  • Air Force/Navy
  • Fitting size

Question 17

Question
What type of damage greatly reduces the ability of tubing to withstand internal pressure and vibration?
Answer
  • Scratches
  • Chafing
  • Dents
  • Nicks

Question 18

Question
A flexible hose in a 3,000 psi system must be pressure tested to
Answer
  • 3,000 psi without bursting
  • 9,000 psi without bursting
  • 12,000 psi without bursting
  • 15,000 psi without bursting

Question 19

Question
When installing a flexible hose, you must provide slack or bend in the hose to
Answer
  • Prevent twisting of the hose
  • Compensate for change in length
  • Place a mechanical load on the hose
  • Protect it from a hot pipe or manifold

Question 20

Question
How can people best prevent FOD?
Answer
  • Look for loose objects (stone, paper, or trash), pick them up when discovered, and encourage others to do the same.
  • Learn the basic classes of FOD, recognize its causes, and account for tools and hardware used during maintenance.
  • Look for loose objects discarded on the flight line during maintenance activities.
  • Periodically participate in “FOD walks” on taxiways and runways.

Question 21

Question
You need to find all of the TOs for a specific weapon system or piece of equipment. What type of index should you use?
Answer
  • TO catalog
  • Alphabetical index
  • Cross-reference table
  • LOAPs

Question 22

Question
You need to find the part number for an item prior to ordering it from supply. You’ve obtained the appropriate IPB manual for the end-item. What section of the IPB should you use to find the major assembly to which the desired item belongs?
Answer
  • Table of Contents
  • Reference designator index
  • Appropriate figure/illustration
  • National stock number and reference number index

Question 23

Question
Which TCTO is issued to correct unsafe conditions that, if not corrected, could result in serious or fatal injury to personnel?
Answer
  • Saftey
  • Urgent Action
  • Routine Action
  • Immediate Action

Question 24

Question
What type of TCTO is often accomplished by contractors, modification centers, or specific Air Force activities higher than organizational\intermediate-level maintenance due to the complexity involved?
Answer
  • Abbreviated TCTO.
  • Inspection TCTO.
  • Record TCTO.
  • Interim TCTO.

Question 25

Question
The main advantage of using abbreviated TOs is they
Answer
  • Cover safety in more detail
  • Serve as supplemental material
  • Paraphrase and eliminate the need for basic TOs
  • Organize and simplify instructions in a condensed version

Question 26

Question
Periodic inspection work cards are divided into three sections that cover the requirements for
Answer
  • Periodic inspections, lubrication, and special inspections.
  • Periodic inspections, special inspections, and safety.
  • Periodic inspections, lubrication, and safety.
  • Special inspections, lubrication, and safety.

Question 27

Question
Which abbreviated TO provides guidance for checking the general serviceability of a piece of equipment including applicable safety warnings, cautions, and notes?
Answer
  • Lubrication charts
  • Illustrated parts breakdown
  • Service inspection work cards
  • Periodic inspection work cards

Question 28

Question
An example of a TO deficiency is
Answer
  • Improper sequencing of pages
  • Insufficient information
  • Typographical errors
  • Misspelled words

Question 29

Question
Which form should you submit to correct a TO deficiency?
Answer
  • AFTO Form 1000, Deficiency Report.
  • AFTO Form 601A, Change Recommendation
  • AFTO Form 95, Support Equipment Record
  • AFTO Form 22, Technical Manual ™ Change Recommendation and Reply

Question 30

Question
What are the two general classes of Air Force publications?
Answer
  • Pamphlets and manuals
  • Departmental and field
  • Instructions and manuals
  • Supplements and instructions

Question 31

Question
OIs are similar to Air Force instructions, but they apply only to
Answer
  • Air Force wings
  • Support personnel
  • Maintenance personnel
  • Personnel within the issuing organization

Question 32

Question
What type of standard publication is used by lower headquarters to implement, amplify, interpret, or clarify a higher level publication?
Answer
  • Supplements
  • Visual aids
  • Bulletins
  • Manuals

Question 33

Question
The first number of a standard Air Force publication number is referred to as the “series” and represents the
Answer
  • Broad area covered
  • Specific area covered
  • Specific title of the publication
  • Specific military personnel affected

Question 34

Question
Where do you access standard Air Force publications?
Answer
  • Air Force e-Publishing website.
  • LOAPs
  • Base-level functional publication library
  • AFI 33–360

Question 35

Question
What impact is made on the maintenance organization by ensuring availability of adequate parts, equipment, and training?
Answer
  • Increasing bottlenecks and maximizing repair cycle time
  • Increasing bottlenecks and minimizing repair cycle time
  • Eliminating bottlenecks and minimizing repair cycle time
  • Eliminating bottlenecks and maximizing repair cycle time

Question 36

Question
Which maintenance levels are considered together as “field maintenance”?
Answer
  • Centralized and depot
  • Depot and provisional
  • Provisional and centralized
  • Organizational and intermediate

Question 37

Question
Organizational maintenance consists of
Answer
  • On-equipment tasks normally performed using the resources of an operating command at an operating location.
  • On-equipment tasks normally performed using the resources of a supporting command or intermediate repair facility.
  • Off-equipment tasks normally performed using the resources of an operating command at an operating location or intermediate repair facility.
  • On- or off-equipment tasks that require highly specialized skills, sophisticated shop equipment, and/or special facilities of a supporting command

Question 38

Question
The main purpose of the inspection system is to
Answer
  • Get ahead on unscheduled maintenance
  • Keep equipment operating and looking good
  • Keeping the mechanic working on minor problems
  • Locate problems and repair equipment before total failure

Question 39

Question
The maintenance symbol the represents the most serious operational condition for equipment is a
Answer
  • Rex X
  • Red Dash
  • Red Diagonal
  • Circled Red X

Question 40

Question
Which symbol indicates an operational check is overdue?
Answer
  • Red X
  • Red Dash
  • Red Diagonal
  • Circled Red X

Question 41

Question
Which section of the AFTO Form 244 is used to record a forms review?
Answer
  • Part II, Non-scheduled Inspection
  • Part III, Scheduled Inspection
  • Part IV, Supervisory Review
  • Part V, Maintenance/Delayed Discrepancy

Question 42

Question
When closing out an AFTO Form 244, what is entered on the form to close out uncompleted inspections?
Answer
  • A red X and your initials in Part IV, Supervisory Review
  • A red X and your initials in Part III, Scheduled Inspections
  • The letters “CF” (for carried forward) and your initials in Part IV, Supervisory Review
  • The letters “CF” (for carried forward) and your initials in Part III, Scheduled Inspections

Question 43

Question
What is the condition of a component bearing a green equipment condition label?
Answer
  • Unserviceable (Condemned)
  • Unserviceable (Repairable)
  • Serviceable
  • Suspended

Question 44

Question
What color is the equipment condition tag attached to an item being held as an exhibit?
Answer
  • Brown
  • Green
  • White
  • Yellow

Question 45

Question
What maintenance supply form is used to order commonly stocked supplies or turn in excess or unserviceable property?
Answer
  • AF Form 2005
  • AFTO Form 350
  • DD Form 1348-6
  • DD Form 1348-1A

Question 46

Question
What MDD code identifies the system that was worked on?
Answer
  • Type maintenance
  • Work unit code
  • Category of labor
  • Units

Question 47

Question
Distinguish between “excess” and “surplus” as they apply to Air Force supply discipline.
Answer
  • Excess and surplus are the same.
  • Excess and surplus are the turn-in of property no longer needed.
  • Surplus is property no longer needed at your base, and excess is property no longer needed by another military service or Federal agency.
  • Excess is property no longer needed at your base, and surplus is property no longer needed by another military service or Federal agency.

Question 48

Question
What is a major concept regarding “economic use” of supplies and equipment?
Answer
  • Use them only for their intended purposes.
  • Always order the least expensive item to do the job.
  • Protect items from hazards such as fire or corrosion.
  • Order only the minimum supplies necessary to do a job.

Question 49

Question
Who is responsible for ensuring that property records of supply transactions are kept accurately?
Answer
  • Commander
  • Supervisor
  • Person who signed for an account
  • Person who has possession of the property

Question 50

Question
To be held responsible for property, you must
Answer
  • Possess it
  • Sign for it
  • Be a 5 level
  • Be a supervisor

Question 51

Question
What are you required to do with Air Force property you might find and believe it to be lost or misplaced?
Answer
  • Leave it where you found it
  • Place it back into the supply system.
  • Take the item to the organizational commander.
  • Take it to the security forces lost and found section.

Question 52

Question
What equipment does not require an AFTO Form 375?
Answer
  • Items less than $2,500
  • Items less than $25,000
  • Items more than $2,500
  • Items more than $25,000

Question 53

Question
Items that retain their identity throughout the period of their use and may be turned in and reissued for use by others are considered
Answer
  • DIFM
  • Excess
  • Expendable
  • Nonexpendable

Question 54

Question
When the bench stock quantity level falls below 50 % for an item, you should
Answer
  • Post a due-out list
  • Place a red tag on the bin
  • Notify supply that stock level is low
  • Initial the initial supply stock listing

Question 55

Question
The responsibility of a person to make good any loss, destruction, or damage of government property caused by misuse or neglect is what kind of liability?
Answer
  • Property
  • Personal
  • Pecuniary
  • Command

Question 56

Question
How can a person be relieved from property responsibility other than by pecuniary liability?
Answer
  • Turn-in only
  • Transfer only
  • Turn-in or Transfer
  • Cash collection voucher or statement of charges

Question 57

Question
A statement of charges would be prepared under which of these circumstances?
Answer
  • If a lost item is not expendable
  • If you make a cash payment for a lost item
  • If you signed a hand receipt for a lost item
  • If you want to use payroll deduction to pay the cost of a lost item

Question 58

Question
What must be done if SSgt Ortiz refuses to admit pecuniary liability for the loss of a $275 lawn mower for which he has custodial responsibility?
Answer
  • A report of survey must be initiated.
  • A statement of charges must be prepared.
  • Charges must be made on a military pay order.
  • The mower must be replaced by one of equivalent value.

Question 59

Question
After a deficiency has been discovered, when must a category II PQDR be submitted to the screening point?
Answer
  • 24 hours
  • 2 calendar days
  • 5 calendar days
  • 10 calendar days

Question 60

Question
Within the deficiency reporting system, who is responsible for the resolution of the deficiency?
Answer
  • Originating point
  • Screening point
  • Action point
  • Support point

Question 61

Question
Within the deficiency reporting system, who assigns a report control number and ensures proper marking and handling of exhibits?
Answer
  • Originating point
  • Screening point
  • Action point
  • Support point

Question 62

Question
Who should AGE maintainers contact for submittal format of agenda items when preparing for the PIWG?
Answer
  • MAJCOM AGE functional managers
  • Screening point within the originating activity
  • Lead command (AFMC)
  • WR-ALC

Question 63

Question
On which type of metal can you leave corrosion as long as the component is operational?
Answer
  • Steel
  • Copper
  • Aluminum
  • None, all corrosion must be removed.

Question 64

Question
What marking is applied to AGE for night safety?
Answer
  • Informational
  • Safety/Danger
  • Reflectorization
  • Caution/Warning

Question 65

Question
Guidelines for storing AGE are in
Answer
  • TO 35-1-3
  • TO 35-1-4
  • TO 35-1-12
  • AFMAN 23-110

Question 66

Question
Which of these items must be removed from test equipment before storage?
Answer
  • Wet and dry cell batteries
  • Dry charge batteries
  • Battery compartment
  • Battery holder

Question 67

Question
What AGE must have the fuel drained when preparing it for mobility?
Answer
  • Equipment with fuel levels that cannot be verified
  • Self-propelled equipment required for immediate use at deployment sites
  • Equipment that is not self-propelled and is required for immediate use at deployment sites
  • All AGE must have fuel drained prior to deployment; there are no exceptions

Question 68

Question
During a battery condition check, what is an acceptable voltage reading for a 12-volt battery?
Answer
  • 8–2 volts
  • 10–12 volts
  • 12.4 volts or lower
  • 12.7 volts or higher

Question 69

Question
After connecting a voltmeter across the starter terminals and clamping a current probe around the positive battery cable, what must be done prior to cranking the engine when performing a starting system check on AGE?
Answer
  • Estimate the temperature of the battery.
  • Prevent the engine from starting.
  • Perform a battery cable test.
  • Disconnect the voltmeter.

Question 70

Question
How should you approach a parked aircraft with your vehicle?
Answer
  • Only when a guide is posted.
  • Within 25 feet of an aircraft with engines running
  • With the driver’s side of the vehicle toward the aircraft
  • With the driver’s side of the vehicle away from the aircraft

Question 71

Question
What should you do if your vehicle meets a moving aircraft at night?
Answer
  • Turn off your headlights and leave your parking lights on.
  • Dim your headlights and continue on.
  • Stop and change directions.
  • Turn all lights off.

Question 72

Question
Why should you apply silicone sealant to the valve stem area of a wheel?
Answer
  • To keep rims from flying apart
  • To keep water from entering rims
  • As a treatment for weather cracks
  • As a treatment for severe corrosion

Question 73

Question
What must you do before inflating the inner tube fully on a split rim tire?
Answer
  • Fully deflate the tire
  • Torque wheel lug bolts
  • Check tires for foreign objects
  • Ensure rims are completely bolted together and torqued.
Show full summary Hide full summary

Want to create your own Quizzes for free with GoConqr? Learn more.

Similar

CDC 2A652N - Volume 2 - Electrical and Electrical Circuits & Components
nicilynn1981
CDC 2A652N - Volume 4 - Common AGE Systems
nicilynn1981
AS Psychology Unit 1 - Memory
Asterisked
Age as a factor affecting eye witness testimony
T W
AS Psychology: Eye Witness Testimony Revision
Asterisked
CAGE and Crime
Gabzay
English Language: Language and Age
Eloise Russell
Inequalities
Yasmine King
Crime & Deviance Cards
Charlotte Gray5800
Age and Religion
danielaRD
Early English Middle Age Medicine
First Name
Browse Library