5841384
Beschreibung
Quiz von Christina Evans, aktualisiert more than 1 year ago
|
Erstellt von Christina Evans
vor mehr als 8 Jahre
|
|
Frage 1
Frage
Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?
Antworten
-
network 172.16.23.64 0.0.0.63
-
network 172.16.23.0 255.255.255.192
-
network 172.16.23.64 0.0.0.127
-
network 172.16.23.0 255.255.255.128
Frage 2
Frage
What is the purpose of using protocol-dependent modules in EIGRP?
Antworten
-
to describe different routing processes
-
to identify different application layer protocols
-
to use different transport protocols for different packets
-
to accommodate routing of different network layer protocols
Frage 3
Frage
If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
Antworten
-
10 seconds
-
15 seconds
-
20 seconds
-
30 seconds
Frage 4
Frage
Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
Antworten
-
update
-
query
-
hello
-
reply
-
acknowledgment
Frage 5
Frage
Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
Antworten
-
01-00-5E-00-00-09
-
01-00-5E-00-00-10
-
01-00-5E-00-00-0A
-
01-00-5E-00-00-0B
Frage 6
Frage
What is identified within the opcode of an EIGRP packet header?
Antworten
-
the EIGRP message type that is being sent or received from a neighbor
-
the EIGRP autonomous system metrics
-
the EIGRP hold timer agreed upon with a neighbor
-
the EIGRP sum of delays from source to destination
Frage 7
Frage
Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
Antworten
-
to lower the router overhead
-
to send a manual summarization
-
to exclude some interfaces from the EIGRP process
-
to subnet at the time of the configuration
Frage 8
Frage
An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
Antworten
-
as the autonomous system number
-
as the number of neighbors supported by this router
-
as the length of time this router will wait to hear hello packets from a neighbor
-
as the maximum bandwidth of the fastest interface on the router
Frage 9
Frage
What information does EIGRP maintain within the routing table?
Antworten
-
both successors and feasible successors
-
only feasible successors
-
adjacent neighbors
-
all routes known to the router
-
only successors
Frage 10
Frage
Which table is used by EIGRP to storre all routes that are learned from EIGRP?
Antworten
-
the routing table
-
The neighbor table
-
The topology table
-
The adjacency table
Frage 11
Frage
Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
Antworten
-
bandwidth 1500
-
shutdown no shutdown
-
copy running-config startup-config reload
-
no bandwidth
Frage 12
Frage
Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
Antworten
-
show ip route
-
show interfaces
-
show ip protocols
-
show ip interface brief
Frage 13
Frage
A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
Antworten
-
bandwidth
-
load
-
reliability
-
delay
-
MTU
Frage 14
Frage
Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)
Antworten
-
192.168.71.0
-
192.168.51.0
-
10.44.100.252
-
10.44.104.253
-
10.44.101.252
Frage 15
Frage
Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
Antworten
-
2340608
-
2169856
-
10512128
-
2816
Frage 16
Frage
How do EIGRP routers establish and maintain neighbor relationships?
Antworten
-
by exchanging neighbor tables with directly attached routers
-
by comparing known routes to information received in updates
-
by exchanging hello packets with neighboring routers
-
by dynamically learning new routes from neighbors
-
by exchanging routing tables with directly attached routers
Frage 17
Frage
What is indicated when an EIGRP route is in the passive state?
Antworten
-
The route has the highest path cost of all routes to that destination network.
-
The route must be confirmed by neighboring routers before it is put in the active state.
-
The route is a feasible successor and will be used if the active route fails.
-
There is no activity on the route to that network.
-
The route is viable and can be used to forward traffic.
Frage 18
Frage
What is the multicast address used by an EIGRP-enabled router operating with IPv6?
Antworten
-
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
-
FF02::A
-
FF02::B
-
FF02::1
Frage 19
Frage
Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
Antworten
-
The eigrp router-id command requires an IPv6 address within the router configuration mode.
-
The network command is required within the router configuration mode.
-
The no shutdown command is required within the router configuration mode.
-
The router eigrp autonomous-system command is required within the router configuration mode.
Frage 20
Frage
Fill in the Blank. Use the abbreviation.
EIGRP uses the [blank_start]RTP[blank_end] protocol to deliver EIGRP packets to neighbors
Antworten
-
RTP
Frage 21
Frage
Fill in the blank.
In an EIGRP topology table, a route that is in a/an [blank_start]active[blank_end] state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
Antworten
-
active
Frage 22
Frage
Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)
Antworten
-
EIGRP for IPv4 only
-
both EIGRP for IPv4 and IPv6
-
EIGRP for IPv6 only
Frage 23
Frage
Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)
Antworten
-
_ first _
-
_ third _
-
_ second _
Frage 24
Frage
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which code is displayed on the web server?
Antworten
-
Done
-
EIGRP
-
Complete
-
IPv6EIGRP
Möchten Sie mit GoConqr kostenlos Ihre eigenen Quiz erstellen? eigenen Mehr erfahren.