Frage 1
Frage
Which type of stencil is best used for producing a complex design?
Antworten
-
a Multi plate.
-
b Positive.
-
c Negative.
-
d Tied.
Frage 2
Frage
The method of using an overlay of squares to enlarge or reduce an image is known as
Antworten
-
a photocopying
-
b a grid system
-
c illuminated projection
-
d accurate measurement.
Frage 3
Frage
What is an advantage of using acetate stencil?
Frage 4
Frage
Chalking on the underside of an image prior to drawing over it is known as
Antworten
-
a photocopying
-
b projecting
-
c pouncing
-
d tracing.
Frage 5
Frage
The advantage of using a craft knife to cut stencils rather than a utility knife is that it has a
Antworten
-
a smaller blade
-
b retractable blade
-
c bigger blade
-
d snap off blade.
Frage 6
Frage
Why is glass sheet the preferred base when cutting multi plate stencils?
Frage 7
Frage
When cutting stencils, what is the approximate angle the knife should be held at?
Antworten
-
a 5-10⁰.
-
b 20-50⁰.
-
c 80-100⁰.
-
d 100-120⁰.
Frage 8
Frage
When cutting stencils, a large margin is used to prevent
Antworten
-
a creep
-
b buckling
-
c lifting
-
d smudging.
Frage 9
Frage
What is the main consideration when setting out linear runs and border stencils for wall areas?
Antworten
-
a Windows and doors.
-
b Room dimensions.
-
c Symmetrical balance.
-
d Stencil size.
Frage 10
Frage
What is the name given to the line which is placed on the stencil and used to level against the chalk line?
Antworten
-
a Centre line.
-
b Horizontal line.
-
c Vertical line.
-
d Registration line.
Frage 11
Frage
What is the main advantage of using low tack tape when securing stencil plates to finished surfaces?
Frage 12
Frage
What defect can occur when too much paint is applied to a stencil plate?
Antworten
-
a Cissing.
-
b Creep.
-
c Bittiness.
-
d Lifting.
Frage 13
Frage
What is the main cause of buckled or curled paper stencils?
Frage 14
Frage
What should a stencil brush be cleaned in after using water-borne stencil materials?
Antworten
-
a Brush restorer.
-
b Warm soapy water.
-
c White spirit.
-
d Methylated spirit.
Frage 15
Frage
How should stencil palettes be maintained and stored after use?
Antworten
-
a Stored in solvent.
-
b Wiped clean and stacked.
-
c Stored in lint free cloth.
-
d Left to dry and stacked.
Frage 16
Frage
The appropriate ground coat colour must be used on a wood effect to
Frage 17
Frage
Which one of the following pigments can be used in both solvent and water borne materials?
Antworten
-
a Universal stainers.
-
b Artists oil.
-
c Acrylics.
-
d Gouache.
Frage 18
Frage
Which of the following colourants would be suitable to create a mahogany scumble?
Antworten
-
a Raw umber.
-
b Brunswick green.
-
c Burnt sienna.
-
d Paynes grey.
Frage 19
Frage
What is the final stage of the drying process for solvent borne scumble?
Antworten
-
a Coalescence.
-
b Evaporation.
-
c Oxidation.
-
d Polymerisation.
Frage 20
Frage
Which one of the following tools can be used to create coarse grain in oak?
Antworten
-
a Combs.
-
b Feathers.
-
c Flogger.
-
d Fantail fitch.
Frage 21
Frage
Which one of the following brushes is used to simulate the pore markings in oak?
Antworten
-
a Softener.
-
b Flogger.
-
c Overgrainer.
-
d Mottler.
Frage 22
Frage
Which one of the following tools is used to apply fine parallel grain patterns to completed work?
Antworten
-
a Softener.
-
b Flogger.
-
c Pencil overgrainer.
-
d Mottler.
Frage 23
Frage
Prior to storage, steel combs should be
Antworten
-
a lightly abraded
-
b lightly oiled
-
c degreased
-
d primed.
Frage 24
Frage
Cutting vertically through the centre of the tree trunk will reveal the pattern known as
Antworten
-
a heartwood
-
b end grain
-
c quarter grain
-
d overgrain.
Frage 25
Frage
Wiping out with a rag over a veining horn on wood effect is used to produce
Antworten
-
a straight grain
-
b heartwood
-
c mottling
-
d flogging.
Frage 26
Frage
Which one of the following describes the process to gently fade out sharp edges of a wood effect?
Antworten
-
a Overgraining.
-
b Rubbing in.
-
c Softening.
-
d Combing.
Frage 27
Frage
When applying a wood grain effect to a panel door where would the finishing point be?
Antworten
-
a Muntins.
-
b Panels.
-
c Styles.
-
d Rails.
Frage 28
Frage
How are the veins in natural marble formed?
Antworten
-
a Minerals.
-
b Man made.
-
c Limestone.
-
d Crystallisation.
Frage 29
Frage
Which one of the following is the BS4800 groundcoat colour for Vert de mer?
Antworten
-
a 00E53
-
b 20E51
-
c 00E55
-
d 00A01
Frage 30
Frage
Which one of the following is the main pigment colour used in black and gold?
Antworten
-
a Sienna.
-
b Ultramarine blue.
-
c Brunswick green.
-
d Umber.
Frage 31
Frage
Which one of the following is the main tool used to produce marble effects?
Antworten
-
a Check roller.
-
b Dragger.
-
c Veining horn.
-
d Feather.
Frage 32
Frage
Which one of the following brushes is best suited to producing veins in marble?
Antworten
-
a Flogger.
-
b Softener.
-
c Dragger.
-
d Sable.