L3 Central Heating Revision

Descripción

Central heating revision
gaby khalil
Test por gaby khalil, actualizado hace más de 1 año
gaby khalil
Creado por gaby khalil hace más de 9 años
3236
4

Resumen del Recurso

Pregunta 1

Pregunta
According to the Domestic Heating Compliance Guide, a device that takes heat energy from a low-temperature source and upgrades it to a temperature that could be used for heating, is known as a:
Respuesta
  • a) heat pump
  • b) solar heating panel
  • c) combined heat and power boiler
  • d) condensing boiler

Pregunta 2

Pregunta
Which one of the following is used to indicate the U value through a building fabric?
Respuesta
  • a) W/m² ºC.
  • b) W/m³ ºC.
  • c) W x r ºC.
  • d) W + r ºC.

Pregunta 3

Pregunta
Which one of the following Building Regulations covers the requirements for combustion appliances?
Respuesta
  • a) Part A (C in Northern Ireland).
  • b) Part J (N in Northern Ireland).
  • c) Part L (K in Northern Ireland).
  • d) Part P (P in Northern Ireland).

Pregunta 4

Pregunta
Which one of the following government departments provides information on the Boiler Efficiency Database?
Respuesta
  • a) DfES. (Department for Education and Skills ..(DfES)
  • b) DEFRA. (Department for Environment, Food and Rural Affairs (Defra)
  • c) BERR. (Department for Business, Enterprise and Regulatory Reform)
  • d) DIUS. (Department for Innovation, Universities and Skills)

Pregunta 5

Pregunta
A central heating system in which the water supplied to the system is fed directly from the cold water supply pipe is
Respuesta
  • a) open vented fully pumped
  • b) open vented gravity
  • c) unvented hot water
  • d) sealed system

Pregunta 6

Pregunta
According to the Domestic Heating Compliance Guide, what is the minimum SEDBUK value for a gas or oil fired central heating boiler installed in an existing dwelling after 1 April 2007?
Respuesta
  • a) 76%.
  • b) 80%.
  • c) 82%.
  • d) 86%.

Pregunta 7

Pregunta
Which one of the following methods is usually preferred for determining the boiler output when replacing an existing oil or gas fired boiler?
Respuesta
  • a) Replace like for like.
  • b) Whole house boiler sizing method.
  • c) Add 30% to existing output.
  • d) Only use SEDBUK band D boilers.

Pregunta 8

Pregunta
According to the Domestic Heating Compliance Guide, which one of the following organisations operates an approvals scheme for solid fuel boilers and heating appliances?
Respuesta
  • a) CORGI.
  • b) OFTEC.
  • c) HETAS.
  • d) NICEIC.

Pregunta 9

Pregunta
Which one of the following should be the minimum distance, in mm, between a boiler flue and any combustible material when it passes through a cupboard?
Respuesta
  • a) 10.
  • b) 15.
  • c) 25.
  • d) 50.

Pregunta 10

Pregunta
Which one of the following would be the most desirable pump location in an open vented fully pumped central heating system?

Pregunta 11

Pregunta
Which one of the following is the name of the point at which an expansion vessel connects to a central heating system?
Respuesta
  • a) Negative point.
  • b) Neutral point.
  • c) Positive point.
  • d) Central point.

Pregunta 12

Pregunta
The condensate pipework from a high efficiency (condensing) boiler should be laid at a minimum fall of
Respuesta
  • a) 1.5º
  • b) 2.5º
  • c) 5º
  • d) 10º

Pregunta 13

Pregunta
Which one of the following test methods is used to determine the soundness of a central heating system?
Respuesta
  • a) Hydraulic pressure.
  • b) Visual inspection.
  • c) Hydrostatic pressure.
  • d) Pneumatic pressure.

Pregunta 14

Pregunta
Which one of the following types of central heating system is shown in the Figure?
Respuesta
  • a) Fully pumped system with 2 x two port valves.
  • b) Fully pumped system with mid-position valve.
  • c) Pumped heating with unvented hot water.
  • d) Sealed central heating system.

Pregunta 15

Pregunta
Which one of the following types of central heating system is shown in the Figure?
Respuesta
  • a) Pumped heating with unvented hot water.
  • b) Fully pumped system with 2 x two port valves.
  • c) Sealed central heating system.
  • d) Fully pumped system with 3 ports valve.

Pregunta 16

Pregunta
Which one of the following types of central heating system is shown in the Figure?
Respuesta
  • a) Fully pumped system with 2 x two port valves.
  • b) Fully pumped system with mid-position valve.
  • c) Pumped heating with unvented hot water.
  • d) Sealed central heating system.

Pregunta 17

Pregunta
Which one of the following is the likely effect on the heating system when the pump is positioned as shown in the Figure?
Respuesta
  • a) The system is put under neutral pressure.
  • b) The system is put under positive pressure.
  • c) Water is likely to be pumped over the vent.
  • d) Air would be sucked in through the vent.

Pregunta 18

Pregunta
Which one of the following is the likely effect on the heating system when the pump is positioned as shown in the Figure?
Respuesta
  • a) The system is put under neutral pressure.
  • b) The system is put under positive pressure.
  • c) Water is likely to be pumped over the vent.
  • d) Air would be sucked in through the vent.

Pregunta 19

Pregunta
In the central heating system shown in the Figure , what is the name of Component A
Respuesta
  • a) Zone valve.
  • b) 3 port mid position valve.
  • c) Pressure relief valve.
  • d) Automatic air vent.

Pregunta 20

Pregunta
The minimum size of earthling cable, in mm, used to bond the main services in a domestic property is
Respuesta
  • a) 2.5 mm2
  • b) 6 mm2
  • c) 10mm2
  • d) 12 mm2

Pregunta 21

Pregunta
Which one of the following items of equipment could be used to test temperature differential between the heating flow and return pipework?
Respuesta
  • a) Multi-meter
  • b) Manometer.
  • c) Ammeter.
  • d) Digital thermometer.

Pregunta 22

Pregunta
The pressure gauge in a sealed heating system should be capable of reading a pressure range, in bars, of
Respuesta
  • a) 0 to 3
  • b) 0 to 4
  • c) 1 to 4
  • d) 2 to 5.

Pregunta 23

Pregunta
When commissioning a gas fired combination boiler, which one of the following activities should be carried out after turning on the mains water supply?
Respuesta
  • a) Check the water level is correct in the CWSC.
  • b) Purge the hot water pipework of air.
  • c) Check the water level is correct in the F&E cistern.
  • d) Isolate the boiler at the fused spur outlet.

Pregunta 24

Pregunta
Information related to the performance specification of an LPG fired central heating boiler is obtained from
Respuesta
  • a) SEDBUK
  • b) Building Regulations Part L (F in Northern Ireland)
  • c) Manufacturer’s instructions
  • d) CORGI.

Pregunta 25

Pregunta
When commissioning a gas fired system boiler, adjustment to the heat output of the boiler is achieved by
Respuesta
  • a) adjusting the room thermostat
  • b) adjusting the cylinder thermostat
  • c) range rating the boiler
  • d) balancing the system.

Pregunta 26

Pregunta
Which one of the following would be the first action prior to de-commissioning a central heating system in an unoccupied dwelling?
Respuesta
  • a) Seek permission to carry out the work from the Local Authority.
  • b) Contact the utility services to isolate the gas and electricity supplies to the building.
  • c) Ensure that the content of the heating system is drained into containers and disposed of.
  • d) Ensure that all the incoming services have been safely isolated.

Pregunta 27

Pregunta
Which one of the following would contain a fault finding chart for a specific solid fuel boiler?
Respuesta
  • a) HETAS manual.
  • b) Domestic Heating Compliance Guide.
  • c) OFTEC manual.
  • d) Manufacturer’s instructions.

Pregunta 28

Pregunta
When determining the output of a gas central heating boiler, how many kW should be allowed for the hot water heating circuit with a cylinder of 100 – 120 litres?
Respuesta
  • a) 2 kW.
  • b) 4 kW.
  • c) 6 kW.
  • d) 8 kW.

Pregunta 29

Pregunta
Which one of the following should be included on a Benchmark Service Interval Record?
Respuesta
  • a) Flow and return temperature.
  • b) Gas inlet pressure.
  • c) Gas Safe Register ID card serial number.
  • d) Gas flue analysis results.

Pregunta 30

Pregunta
The Domestic Heating Compliance Guide refers to ‘boiler interlock’. This can be described as a
Respuesta
  • a) wiring arrangement preventing the boiler from firing when each circuit has shut off
  • b) security setting on the boiler to prevent the possibility of tampering by the customer
  • c) wiring arrangement to remove the residual heat from the boiler to the heat leak radiator
  • d) system of isolating the boiler when the frost thermostat is activated.

Pregunta 31

Pregunta
According to the Domestic Heating Compliance Guide, a heating system that supplies heat to a number of dwellings from a common heat source is known as
Respuesta
  • a) combination heating
  • b) community heating
  • c) central heating
  • d) combined heat and power.

Pregunta 32

Pregunta
On boilers fitted with digital displays, which one of the following display codes takes priority over other codes?
Respuesta
  • a) Status.
  • b) Diagnostic.
  • c) Fault.
  • d) Memory.

Pregunta 33

Pregunta
Which one of the following government departments provides information on the Boiler Efficiency Database?
Respuesta
  • a) DfES.
  • b) DEFRA.
  • c) BERR.
  • d) DIUS.

Pregunta 34

Pregunta
Guidance on how to satisfy the Building Regulations energy efficiency requirements when carrying out central heating work on new buildings can be found in
Respuesta
  • a) Approved Document E (B in Northern Ireland)
  • b) Approved Document G (C in Northern Ireland)
  • c) Approved Document J (E in Northern Ireland)
  • d) Approved Document L1A (F1 in Northern Ireland).

Pregunta 35

Pregunta
When installing a high efficiency (condensing boiler), provision must be made for a
Respuesta
  • a) discharge pipe run to a drain or soakaway
  • b) double check valve to be installed on the primary flow
  • c) single check valve to be installed on the vent pipe
  • d) flow meter to be installed on the gas valve.

Pregunta 36

Pregunta
Which one of the following is the name of Component A shown in the Figure?
Respuesta
  • a) Automatic by-pass valve.
  • b) Wheel head valve.
  • c) 2 port motorised valve.
  • d) Air separator.

Pregunta 37

Pregunta
Which one of the following is the normal pressure for soundness testing a wet central heating system?
Respuesta
  • a) 0.5 times the maximum operating pressure.
  • b) 1.5 times the maximum operating pressure.
  • c) 2 times the maximum operating head.
  • d) 2.5 times the maximum operating head.

Pregunta 38

Pregunta
14 Which one of the following types of central heating system is shown in the Figure?
Respuesta
  • a) Fully pumped system with 2 x two port valves.
  • b) Fully pumped system with mid-position valve.
  • c) Pumped heating with gravity primary flow and return.
  • d) Sealed central heating system.

Pregunta 39

Pregunta
Which one of the following is the likely effect on the heating system when the pump is positioned as shown in the Figure?
Respuesta
  • a) The system is put under negative pressure.
  • b) The system is put under positive pressure.
  • c) Water is likely to be pumped over the vent.
  • d) Air would be sucked in through the vent.

Pregunta 40

Pregunta
Which one of the following is the correct size of fuse, in amps, for protecting a domestic central heating circuit?
Respuesta
  • a) 3 amp
  • b) 5. amp
  • c) 13. amp
  • d) 16. amp

Pregunta 41

Pregunta
The pressure relief valve in a sealed heating system should discharge at what pressure?
Respuesta
  • a) 1bar
  • b) 2 bars
  • c) 3 bars
  • d) 4 bars

Pregunta 42

Pregunta
The meaning of the status codes on the digital display indicator on a central heating boiler can be obtained from
Respuesta
  • a) inside the combustion chamber
  • b) SEDBUK
  • c) Manufacturer’s instructions
  • d) SBGI.

Pregunta 43

Pregunta
Information related to the performance specification of a natural gas fired central heating boiler is obtained from
Respuesta
  • a) CORGI
  • b) Building Regulations Part L (F in Northern Ireland)
  • c) SEDBUK
  • d) Manufacturer’s instructions.

Pregunta 44

Pregunta
When commissioning central heating systems, manufacturers generally recommend that the system is
Respuesta
  • a) flushed, run at operating temperature, drained, flushed and re-charged
  • b) tested at operating temperature for 30 minutes at 0.5 times operating pressure
  • c) left for a period of 24 hours before being put into service after commissioning
  • d) tested at 0.5 times normal operating temperature for 15 minutes.

Pregunta 45

Pregunta
Which one of the following system components provides an indication that a sealed central heating system has been installed?
Respuesta
  • a) Heat leak radiator.
  • b) mid position valve.
  • c) Expansion vessel.
  • d) Air separator.

Pregunta 46

Pregunta
Which one of the following would contain a fault finding chart for a specific high efficiency gas systems boiler?
Respuesta
  • a) British Standard 6700.
  • b) Domestic Heating Compliance Guide.
  • c) Manufacturer’s instructions.
  • d) British Standard 5449.

Pregunta 47

Pregunta
Insufficient water flow rate through the heat exchanger of a boiler is usually the cause of
Respuesta
  • a) kettling
  • b) temperature relief discharge
  • c) pressure relief discharge
  • d) boiler overrun.

Pregunta 48

Pregunta
Which one of the following shown in the Figure is a manufacturer’s replacement part for a typical gas fired combination boiler?
Respuesta
  • a) Compact thermal module.
  • b) Fan assembly.
  • c) Secondary heat exchanger.
  • d) Burner assembly.

Pregunta 49

Pregunta
Your Diploma in plumbing level 3 is an NVQ qualification
Respuesta
  • True
  • False

Pregunta 50

Pregunta
When completing your plumbing L3 diploma you will be gas qualified engineer
Respuesta
  • True
  • False

Pregunta 51

Pregunta
The Gas (Installation & Use), Regulation 3, specifies the qualifications required to carry out work in relation to gas fittings and gas storage. Which one of the following describes the minimum level of qualification required?
Respuesta
  • A) A fully qualified plumber to NVQ Level 3 standard.
  • B) A member of a class of person approved by HSE
  • C) A person regularly attending manufacture appliance training courses
  • D) A person that has successfully completed an accredited course

Pregunta 52

Pregunta
What type of open vented system is shown in the diagram?
Respuesta
  • a) Fully pumped with two mid position valves.
  • b) Partially pumped heating with gravity hot water.
  • c) Fully pumped with 2 x two port valves.
  • d) Partially pumped using a mid position valve.

Pregunta 53

Pregunta
What is the main feature when designing a space heating circuit to a dwelling with a floor area In excess of 150 m²
Respuesta
  • a) A single zone with weather compensated control and optimum start.
  • b) A single zone with optimum start and TRVs on all radiators
  • c) Multiple zones with separate time and temperature controls
  • d) Multiple zones with a single time controller and TRVs on each radiator.

Pregunta 54

Pregunta
Which one of the following identifies this process occurs whereby the outside temp of the building is measured in order to adjust the heating start time?
Respuesta
  • a) Optimum start.
  • b) Delayed start.
  • c ) Thermo start
  • d) Manual start.

Pregunta 55

Pregunta
Which one of the following types of heating system uses the components In the image shown?
Respuesta
  • a) C Plan.
  • d) W Plan.
  • c) S Plan.
  • b) Y Plan,

Pregunta 56

Pregunta
which one of the following statements best describes the function of a Boiler interlock
Respuesta
  • a) A bypass arrangement in the primary flow and return to assist the boiler in removing excess hot water.
  • b) A wiring arrangement that permits the frost stat to override all other controls when the outside temperature rises
  • c) An arrangement permitting hot water to be obtained without the heating circuit being in operation
  • d) A wiring arrangement that prevents the boiler firing unless there IS a demand from either the water of space heating

Pregunta 57

Pregunta
Which one of the following Is a correct description of the circuit shown?
Respuesta
  • A- Fully pumped hot water and multiple space heating system.
  • B- Fully pumped incorporating two 2 port valves.
  • C- Fully pumped incorporating a 3 port valve.
  • D- Fully pumped heating, gravity hot water.

Pregunta 58

Pregunta
which one of the following heating systems is Indicated by the wiring diagram shown?
Respuesta
  • A- Fully pumped hot water and multiple space heating system.
  • B- Fully pumped incorporating two 2 port valves.
  • C- Fully pumped incorporating a 3 port valve.
  • D- Fully pumped heating, gravity hot water.

Pregunta 59

Pregunta
Which one of the following heating systems is indicated by the wiring diagram shown?
Respuesta
  • a) S plan plus
  • b) C plan plus
  • c) W plan
  • d) Y plan

Pregunta 60

Pregunta
Work is being undertaken on the wiring centre of a central system. Which one of the following actions should be taken in addition to switching off the electrical supply at the fuse spur?
Respuesta
  • a) Ask the customer to turn off the supply and explain it is their responsibility.
  • b) Use a notice which is placed on the consumer unit stating “Do not use”
  • c) Remove and retain the fuse and check for safe isolation of the supply.
  • d) Turn off the electrical supply and carry out the work methodically.

Pregunta 61

Pregunta
A ring final circuit requires the addition of a fused connection for a boiler. Which one of the following indicate the most suitable location to conduct safe isolation in order to carry out this work
Respuesta
  • a) The consumer Unit main switch.
  • b) The circuit breaker for the circuit
  • c) The boiler time clock/controller.
  • d) At the supplier's main cut out fuse

Pregunta 62

Pregunta
What does the use of low loss headers on multi boiler central heating installations enable?
Respuesta
  • A- Smaller capacity F&E cisterns
  • B- A number of balanced independent pump circuits.
  • C- filling loop to be of smaller diameter.
  • D- A reduction in operating pressure in the system.

Pregunta 63

Pregunta
Which one of the following identifies the most important factor when calculating the pipework size for a heating system?
Respuesta
  • A- Water density
  • B- Water velocity.
  • C- Water hardness
  • D- Water viscosity.

Pregunta 64

Pregunta
What type of heating component is shown in the image?
Respuesta
  • A- a pressure gauge.
  • B- an automatic air vent
  • C- an electric thermostat
  • D- a temperature gauge.

Pregunta 65

Pregunta
Both the pressure relief and temperature control valves fail in a sealed heating system. What is the likely outcome in such situation?
Respuesta
  • A- The boiler may stop working.
  • B- The pump may stop working
  • C- The pressure vessel may explode.
  • D- The pressure vessel may overflow.

Pregunta 66

Pregunta
For safety reason, it is important for pressure relief valves to be installed correctly. At what pressure Is a pressure relief valve on a combination boiler normally set to discharge
Respuesta
  • A- 1.5 bar.
  • B- 2 5 bar.
  • C- 3 bar.
  • D- 3.5 bar

Pregunta 67

Pregunta
which one of the following best describes an advantage of using a sealed central heating system?
Respuesta
  • A- lt is less expensive to install.
  • B- lt can serve longer dead legs
  • C- lt has a manual test devise.
  • D- lt produces more heat

Pregunta 68

Pregunta
In a sealed central heating system, which one of the following replaces the open vent pipe in a conventional system?
Respuesta
  • A- Filling loop.
  • B- Non-return valve.
  • C- Pressure relief valve
  • D- Temperature and pressure gauge.

Pregunta 69

Pregunta
The most appropriate position for an expansion vessel is indicated by which one of the following points in the system?
Respuesta
  • A- the highest point.
  • B- the lowest point.
  • C- the coolest part of the system.
  • D- the hottest part of the system.

Pregunta 70

Pregunta
Which type of fuel would not be used in rural areas of the UK where access to a piped fuel supply Is unavailable?
Respuesta
  • A- Fuel oil
  • B- Natural gas.
  • C- Heat pumps.
  • D- Solid fuel.

Pregunta 71

Pregunta
what type of gas heating boiler component is shown In the Image?
Respuesta
  • A- Boiler hood.
  • B- heat exchanger.
  • C- pressure gauge.
  • D- a gas burner.

Pregunta 72

Pregunta
What type of gas heating boiler component is shown in the image?
Respuesta
  • A- water thermostat.
  • B- diverter valve.
  • C- air pressure switch.
  • D- Multifunctional valve.

Pregunta 73

Pregunta
which one of the following boilers requires a drainage pipe to discharge the water produced during the combustion process?
Respuesta
  • A- back boiler
  • B- combination boiler.
  • C- independent boiler
  • D- Condensing boiler.
Mostrar resumen completo Ocultar resumen completo

Similar

P1 quiz
I M Wilson
Médula espinal
Carlos Pineda
GCSE Physics: Energy transfer via heating
waplington99
CEREBELO
Carlos Pineda
Lobulo parietall
Carlos Pineda
Lóbulo temporal
Carlos Pineda
SOLAR HEATING OF THE EARTH
Rawan Ibrahim
Year 11 - Heating processes
Fiona Heathcote
CPU
sayer.l18
SISTEMA NERVIOSO CENTRAL
Carlos Pineda