CCNP Switch 4

If a network engineer applies the command "mac-address-table notification mac-move" on a Cisco switch port, when is the sys log message generated?

Which feature is automatically enabled when a voice VLAN is configured but not automatically disabled when a voice VLAN is removed?

Which statement describes one major issue that VTP can cause in an enterprise network when a new switch is introduced in the network in VTP mode server?

Users of PC1 experience slow connection when a webpage is requested from the server. To increase bandwidth the network engineer configured an EtherChannel on interfaces f1/0 and f0/1 of the server farm switch. server_switch# sh etherchannel load-balance EtherChannel load-balancing operational state (src-mac): Non-IP: Source MAC address IPv4: Source MAC address IPv6: Source MAC address However traffic is still slow. What action can the engineer take to resolve this issue?

A network engineer must implement Ethernet link that are capable of transporting frames and IP traffic for different broadcast domains that are mutually isolated. Consider that this is a multi-vendor environment. Which Cisco IOS switching feature can be used to achieve the task?

On which interface can port security be configured?

Which statement about the MAC address sticky entries in the switch when the copy run start command is entered is true?

Interface f0/1 is configured as a trunk interface that allows all VLANs. This command is configured globally. switch(config)#monitor session 2 filter vlan 1 - 8, 39, 52 What is the result of the implemented command?

Your customer has asked you to come in and verify the operation of R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure. What is the virtual MAC address of HSRP group 1?

Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?

When a private VLAN is configured which mode must be configured as a router facing port? Choose 1

A question about RSPAN configuration in VTPv2.

Which private VLAN access port belongs to the primary and can communicate with all interfaces, including the community and isolated host ports?

What should the configuration be for spanning-tree port-priority based on the diagram?

What happens if an interface within a channel group is configured as SPAN destination?

Which statement about switch S1 is true?

Which command globally enables AAA on a device?

A network engineer is setting up a new switched network. The network is expected to grow and add many new VLANs in the future. Which spanning tree protocol should be used to reduce switch resources and managerial burdens that are associated with multiple spanning-tree instances?

When troubleshooting a network problem, a network analyzer is connected to port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?

What information is contained in a CDP advertisement?

Which two commands ensure that DSW1 becomes the root bridge for VLAN 10 and 20? Choose Two

A network engineer must adjust STP interface attributes to influence root port selection. Which two elements are used to accomplish this?

Which portion of AAA looks at what a user has access to?

Switch A, B and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A but B does not receive any information. What is most likely the cause of this behavior?

What VTP mode is needed to configure an extended VLAN when a switch is configured to use VTP versions 1 or 2?

Which gateway role is responsible for answering ARP requests for the virtual IP address in GLBP?

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration. Refer to the configuration. For which configured VLAN are untagged frames sent over trunks between SW1 and SW2?

A network engineer changed the port speed and duplex settings of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?

A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of the issue?

On which layer does IP source guard provide filtering to prevent a malicious host from impersonating the IP address of a legitimate host?

When two MST instances (MST 1 and MST 2) are created on a switch, what is the total number of spanning-tree instances running on the switch?

Based on the debug output, which three statements about HSRP are true?

Which action allows a network engineer to limit a default VLAN from being propagated across all trunks?

Which statement is true about RSTP topology changes?

Which option is a possible cause for an err-disable interface?

What is Cisco recommendation for RSPAN best practices?

Which configuration command ties the router host standby priority to the availability of its interfaces?

What is needed for Virtual Switching System (VSS) ?

Hotspot – HSRP Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution. – DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105 – DSW2 – primary device for VLAN 103 and VLAN 104 – A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed. Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question. What is the priority value of the VLAN 105 HSRP group on DSW2? Use sh standby br on console 2

What is the default HSRP priority?

Which statement about the use of SDM templates in a Cisco switch is true?

Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?

Which option lists that modes that are available for configuring UDLD on a Cisco switch?

How will the traffic reach the core switch from AZ switch to DS core switch?

Which configuration ensures that the CDP packet update frequency sent from DSW1 to ALS1 is half of the default value?

An engineer has run the show EtherChannel summary command and the output is displayed. Which statement about the status of the EtherChannel is true?

Which command would a network engineer apply to err-disable a switchport when a packet-storm is detected?

Which VRRP router is responsible for forwarding packets that are sent to the IP address of the virtual router?

If GiE1/0/1 on DSW2 is shutdown what will be the resulting priority value of the VLAN 105 HSRP group on router DSW2?

What does the command "vlan dot1q tag native" accomplish when configured under global configuration?

What type of SDM templates can you use on a switch? Choose 4

Interfaces are assigned to a VLAN and then the VLAN is deleted. Which state are these interfaces in after the VLAN is deleted?

If HSRP group number is 45 what would the MAC address be?

When a Layer 2 EtherChannel is configured which statement about placement of the IP address is true?

Which SDM templates is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?

Which SDM template disables routing and supports maximum number of unicast MAC addresses?