8787689
Descrição
Quiz por james crowley, atualizado more than 1 year ago
|
Criado por james crowley
mais de 7 anos atrás
|
|
Questão 1
Questão
Which type of stencil is best used for producing a complex design?
Responda
-
a Multi plate.
-
b Positive.
-
c Negative.
-
d Tied.
Questão 2
Questão
The method of using an overlay of squares to enlarge or reduce an image is known as
Responda
-
a photocopying
-
b a grid system
-
c illuminated projection
-
d accurate measurement.
Questão 3
Questão
What is an advantage of using acetate stencil?
Responda
-
a Self adhesive.
-
b Cheap to buy.
-
c Can see previous design.
-
d Can be used without cleaning.
Questão 4
Questão
Chalking on the underside of an image prior to drawing over it is known as
Responda
-
a photocopying
-
b projecting
-
c pouncing
-
d tracing.
Questão 5
Questão
The advantage of using a craft knife to cut stencils rather than a utility knife is that it has a
Responda
-
a smaller blade
-
b retractable blade
-
c bigger blade
-
d snap off blade.
Questão 6
Questão
Why is glass sheet the preferred base when cutting multi plate stencils?
Responda
-
a It is transparent.
-
b It is readily available.
-
c It is safer to use.
-
d It does not scar.
Questão 7
Questão
When cutting stencils, what is the approximate angle the knife should be held at?
Responda
-
a 5-10⁰.
-
b 20-50⁰.
-
c 80-100⁰.
-
d 100-120⁰.
Questão 8
Questão
When cutting stencils, a large margin is used to prevent
Responda
-
a creep
-
b buckling
-
c lifting
-
d smudging.
Questão 9
Questão
What is the main consideration when setting out linear runs and border stencils for wall areas?
Responda
-
a Windows and doors.
-
b Room dimensions.
-
c Symmetrical balance.
-
d Stencil size.
Questão 10
Questão
What is the name given to the line which is placed on the stencil and used to level against the chalk line?
Responda
-
a Centre line.
-
b Horizontal line.
-
c Vertical line.
-
d Registration line.
Questão 11
Questão
What is the main advantage of using low tack tape when securing stencil plates to finished surfaces?
Responda
-
a It can be used again.
-
b It does not damage the surface.
-
c It is cheap to buy.
-
d It is very sticky.
Questão 12
Questão
What defect can occur when too much paint is applied to a stencil plate?
Responda
-
a Cissing.
-
b Creep.
-
c Bittiness.
-
d Lifting.
Questão 13
Questão
What is the main cause of buckled or curled paper stencils?
Responda
-
a Not enough sealer.
-
b Left hanging too long.
-
c Too much paint applied.
-
d Not dried properly before reusing.
Questão 14
Questão
What should a stencil brush be cleaned in after using water-borne stencil materials?
Responda
-
a Brush restorer.
-
b Warm soapy water.
-
c White spirit.
-
d Methylated spirit.
Questão 15
Questão
How should stencil palettes be maintained and stored after use?
Responda
-
a Stored in solvent.
-
b Wiped clean and stacked.
-
c Stored in lint free cloth.
-
d Left to dry and stacked.
Questão 16
Questão
The appropriate ground coat colour must be used on a wood effect to
Responda
-
a prevent cissing
-
b prevent fading
-
c increase the durability
-
d ensure a realistic effect.
Questão 17
Questão
Which one of the following pigments can be used in both solvent and water borne materials?
Responda
-
a Universal stainers.
-
b Artists oil.
-
c Acrylics.
-
d Gouache.
Questão 18
Questão
Which of the following colourants would be suitable to create a mahogany scumble?
Responda
-
a Raw umber.
-
b Brunswick green.
-
c Burnt sienna.
-
d Paynes grey.
Questão 19
Questão
What is the final stage of the drying process for solvent borne scumble?
Responda
-
a Coalescence.
-
b Evaporation.
-
c Oxidation.
-
d Polymerisation.
Questão 20
Questão
Which one of the following tools can be used to create coarse grain in oak?
Responda
-
a Combs.
-
b Feathers.
-
c Flogger.
-
d Fantail fitch.
Questão 21
Questão
Which one of the following brushes is used to simulate the pore markings in oak?
Responda
-
a Softener.
-
b Flogger.
-
c Overgrainer.
-
d Mottler.
Questão 22
Questão
Which one of the following tools is used to apply fine parallel grain patterns to completed work?
Responda
-
a Softener.
-
b Flogger.
-
c Pencil overgrainer.
-
d Mottler.
Questão 23
Questão
Prior to storage, steel combs should be
Responda
-
a lightly abraded
-
b lightly oiled
-
c degreased
-
d primed.
Questão 24
Questão
Cutting vertically through the centre of the tree trunk will reveal the pattern known as
Responda
-
a heartwood
-
b end grain
-
c quarter grain
-
d overgrain.
Questão 25
Questão
Wiping out with a rag over a veining horn on wood effect is used to produce
Responda
-
a straight grain
-
b heartwood
-
c mottling
-
d flogging.
Questão 26
Questão
Which one of the following describes the process to gently fade out sharp edges of a wood effect?
Responda
-
a Overgraining.
-
b Rubbing in.
-
c Softening.
-
d Combing.
Questão 27
Questão
When applying a wood grain effect to a panel door where would the finishing point be?
Responda
-
a Muntins.
-
b Panels.
-
c Styles.
-
d Rails.
Questão 28
Questão
How are the veins in natural marble formed?
Responda
-
a Minerals.
-
b Man made.
-
c Limestone.
-
d Crystallisation.
Questão 29
Questão
Which one of the following is the BS4800 groundcoat colour for Vert de mer?
Responda
-
a 00E53
-
b 20E51
-
c 00E55
-
d 00A01
Questão 30
Questão
Which one of the following is the main pigment colour used in black and gold?
Responda
-
a Sienna.
-
b Ultramarine blue.
-
c Brunswick green.
-
d Umber.
Questão 31
Questão
Which one of the following is the main tool used to produce marble effects?
Responda
-
a Check roller.
-
b Dragger.
-
c Veining horn.
-
d Feather.
Questão 32
Questão
Which one of the following brushes is best suited to producing veins in marble?
Responda
-
a Flogger.
-
b Softener.
-
c Dragger.
-
d Sable.
Quer criar seus próprios Quizzes gratuitos com a GoConqr? Saiba mais.