5135280
Question 1
Question
Wet abrading is carried out on which type of ground coating?
Answer
-
a Acrylic borne eggshell.
-
b Oil borne eggshell.
-
c Powdered filler.
-
d Flexible filler.
Question 2
Question
What is the most suitable acrylic borne coating to use as a ground coat when applying a
water borne system?
Answer
-
a Gloss.
-
b Eggshell.
-
c Emulsion.
-
d Undercoat.
Question 3
Question
Which of the following can cause bittiness to decorative work?
Answer
-
a Uneven colour.
-
b Uneven application.
-
c Insufficient material.
-
d Insufficient preparation.
Question 4
Question
What is the correct way to lay off a solvent borne eggshell ground coat on a wall?
Answer
-
a Crisscross.
-
b Vertically.
-
c Arching.
-
d Horizontally.
Question 5
Question
What is the main benefit of using a stipple brush on ground coats?
Answer
-
a It makes the application faster.
-
b It reduces the drying time.
-
c It removes brush marks.
-
d It deepens the colour
Question 6
Question
What material is mixed with a glaze to produce a scumble?
Answer
-
a Oil.
-
b Spirit.
-
c Water.
-
d Colourant
Question 7
Question
What tool is used to create a soft appearance on a glazed surface?
Answer
-
a Natural sponge.
-
b Mohair roller.
-
c Stipple brush.
-
d Chamois leather.
Question 8
Question
Other than boots and overalls, which PPE should be worn when applying broken colour
effect?
Answer
-
a Mask.
-
b Gloves.
-
c Goggles.
-
d Ear plugs.
Question 9
Question
Which of the following describes a glaze?
Answer
-
a A material used to extend the drying time in paint.
-
b One of the additives that make up a scumble.
-
c A material used to make up a stencil.
-
d An additive that makes up a primer.
Question 10
Question
Which material is used to extend the drying time in oil borne scumble?
Answer
-
a White spirit.
-
b Linseed oil.
-
c Colourant.
-
d Glaze.
Question 11
Question
What will cause yellowing to broken colour after a period of time?
Answer
-
a Lack of light.
-
b Lack of spirit.
-
c Lack of scumble.
-
d Lack of colourant
Question 12
Question
Why should more scumble than needed be mixed together for a piece of work?
Answer
-
a To save time.
-
b To repair damage.
-
c To allow for spillages.
-
d To prepare for the next job
Question 13
Question
Adding thinners to the scumble will alter the effect by
Answer
-
a adding shine
-
b darkening
-
c yellowing
-
d lightening.
Question 14
Question
Which of the following describes a substrate that allows light to pass through but cannot
be seen through?
Answer
-
a Translucent.
-
b Reflective.
-
c Transparent.
-
d Opaque.
Question 15
Question
When rag rolling what application fault is caused by not overlapping the pattern?
Answer
-
a Creeping.
-
b Skidding.
-
c Bleeding.
-
d Banding
Question 16
Question
How can skidding be prevented?
Answer
-
a Keeping a wet edge going.
-
b Crossing over when ragging.
-
c Using the correct ground coat.
-
d Mixing the correct ratio of materials
Question 17
Question
What would happen if incorrect tape is used when masking?
Answer
-
a Uneven edges.
-
b Crisp edges.
-
c Bleeding.
-
d Creepage.
Question 18
Question
Damage to surface when removing masking tape is mainly caused by
Answer
-
a incorrect tape choice
-
b pulling the tape off slowly
-
c reducing the tackiness of the tape
-
d pulling the tape towards the surface.
Question 19
Question
What is the correct process when cleaning chamois leathers?
Answer
-
a Wash, fold, store.
-
b Dry, fold, store.
-
c Wash, dry, store.
-
d Hang, dry, store.
Question 20
Question
How should brushes be stored after cleaning to allow for drying?
Answer
-
a Hung in ventilated area.
-
b Hung up in a cupboard.
-
c Laid on a bench.
-
d Laid in a box.
Question 21
Question
What type of stencil is cut out and paint applied over the opening shown in the image?
Answer
-
a Positive.
-
b Multi.
-
c Plate.
-
d Negative
Question 22
Question
When carrying out stencil work in a room the focal point is most likely to be a
Answer
-
a chimney breast
-
b wall with a door
-
c window wall
-
d corner.
Question 23
Question
What is the main purpose of registration marks?
Answer
-
a To find the centre.
-
b To keep the stencil level.
-
c To identify the starting point.
-
d To identify the finishing point
Question 24
Question
Why should low tack tape be used to secure stencil plates?
Answer
-
a To prevent buckling.
-
b To prevent creeping.
-
c To prevent uneven colour.
-
d To prevent surface damage.
Want to create your own Quizzes for free with GoConqr? Learn more.