Copiar e Editar

Millwright Test 1

Descrição

Millwright CofQ Millwright Exam Prep. Quiz sobre Millwright Test 1, criado por Lukasz N em 08-04-2022.
Lukasz N
Quiz por Lukasz N, atualizado 8 meses atrás
Lukasz N
Criado por Lukasz N mais de 2 anos atrás
3
0
0

Resumo de Recurso

Questão 1

Questão
What Part and Section of the OHS Code describes the membership of a joint work site health and safety committee?
Responda
  • Part 12, Section 197
  • Part 13, Section 197
  • Part 14, Section 197
  • Part 15, Section 197

Questão 2

Questão
What Part and Section of the OHS Code describes the requirements and options for protective footwear?
Responda
  • Part 18, Section 229
  • Part 18, Section 232
  • Part 18, Section 233
  • Part 18, Section 236

Questão 3

Questão
What Part and Section of the OHS Code describes the requirements and options for worker training about WHMIS?
Responda
  • Part 29, Section 394
  • Part 29, Section 395
  • Part 29, Section 396
  • Part 29, Section 397

Questão 4

Questão
What are the first aid requirements for high hazard work at a close work site with 5 to 9 workers at the work site per shift?
Responda
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 3 First Aid Kit, 3 blankets, stretcher, splint
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit

Questão 5

Questão
What is employer responsibility with regard to hazard assessment at the work site?
Responda
  • to provide easy and immediate access for any worker to the OHS Act, Regulation and Code at the work site
  • to ensure suppliers are aware of their responsibility to provide necessary information on any hazards related to their products
  • to develop a plan to eliminate or control any hazard identified at the work site
  • to ensure all workers participate in daily meetings to inspect their tools and plan their work

Questão 6

Questão
How is Workers Compensation Board of Alberta funded?
Responda
  • 100% of the funding for the WCB comes from employers in Alberta.
  • 75% of the funding for the WCB comes from employers and 25% comes from the provincial government
  • 50% of the funding for the WCB comes from employers, 25% from the provincial government and 25% from employees
  • 33% of the funding for the WCB comes from employers, 34% from the provincial government and 33% from employees

Questão 7

Questão
What are the four categories of workplace hazards?
Responda
  • ecological, chemical, ergonomic, physical
  • biological, chemical, ergonomic, physical
  • biological, ecological, chemical, physical
  • chemical, physical, psychological, ecological

Questão 8

Questão
What is an example of an engineering control for worker protection?
Responda
  • renovation
  • subdivision
  • isolation
  • activation

Questão 9

Questão
When is an administrative control put in place for worker protection?
Responda
  • To identify the correct personal protective equipment to be used in a hazardous situation
  • To document the details of the implementation of an engineering control
  • When an engineering control cannot eliminate or control a hazard
  • To isolate a hazard through containment or enclosure

Questão 10

Questão
Who is responsible to have an emergency response plan in place at work site?
Responda
  • employees
  • OHS inspector
  • joint work site health and safety committee
  • employers

Questão 11

Questão
What part of the OHS Code convers first aid requirements at the work site?
Responda
  • Part 10
  • Part 11
  • Part 12
  • Part 13

Questão 12

Questão
What must your employer do if first aid supplies are stored in secure containers at the work site?
Responda
  • Ensure the containers are clearly marked to indicate their contents
  • Ensure the containers are stored in a dust proof environment
  • Ensure the containers are not stacked more than 3 layers high
  • Ensure the containers are inspected monthly to ensure contents are safe

Questão 13

Questão
What number and type of first aiders must your employer ensure are present at an isolated work site with low hazard assessment rating and 65 workers at the work site per shift?
Responda
  • 1 Standard First Aider
  • 1 Standard First Aider and 1 Emergency First Aider
  • 2 Standard First Aiders
  • 2 Standard First Aiders and 1 Emergency First Aider

Questão 14

Questão
What is the duty to use personal protective equipment according to the Alberta OHS Code?
Responda
  • a clause that must be included in the employment contract of every construction worker in Alberta
  • a sign that must be posted at the entrance to any work site where PPE is required
  • the part of the OHS Code that describes the different types of PPE to be used on the work site
  • what you and your employer must do if a hazard assessment identifies the need for the use of PPE

Questão 15

Questão
Who is responsible to ensure work site emergency response plans remain up to date?
Responda
  • the employer
  • the employer and the employees
  • the employees
  • the OHS inspector

Questão 16

Questão
When a work site hazard assessment identifies that workers are required to wear PPE what is your employer's responsibility?
Responda
  • Ensure all workers are informed about the need to wear PPE
  • Ensure all workers properly use and wear the required PPE
  • Put up posters indicating a hazard assessment has identified that PPE is required
  • Ensure all workers are provided with funding to purchase required PPE

Questão 17

Questão
What is an employee responsibility with regard to the use of PPE?
Responda
  • to inspect your PPE once a month
  • to modify poor fitting PPE so it fits properly
  • to inspect your PPE prior to each use
  • to wear your PPE only when you sense an accident may happen

Questão 18

Questão
Industrial protective headwear must comply with what standard?
Responda
  • ULC
  • PPE
  • WCB
  • CSA

Questão 19

Questão
What is not an obligation your employer assumes when a hazard assessment indicates the need for PPE?
Responda
  • to post a Duty To Use Personal Protective Equipment sign at all entrances to the work site
  • to ensure employees are trained in the use, care, limitations and maintenance of their PPE
  • to ensure workers properly use and wear PPE
  • to ensure the PPE is in a condition to perform the function intended

Questão 20

Questão
What is a characteristic of protective footwear with a yellow triangle on the outer side or tongue of the right shoe?
Responda
  • sole puncture protection and Grade 2 protective toe (will withstand impact up to 90 Joules)
  • soles that provide electrical shock protection and a Grade 2 protective toe (will withstand impact up to 90 Joules)
  • sole puncture protection and Grade 1 protective toe (will withstand impact up to 125 Joules)
  • soles that provide electrical shock protection and a Grade 1 protective toe (will withstand impact up to 125 Joules)

Questão 21

Questão
In what situation is your employer obligated to provide you with proper PPE according the OHS Code?
Responda
  • when required PPE must be replaced more frequently that once a year
  • when required PPE must be replaced more frequently that once every 2 years
  • when workers are exposed to respiratory hazard or excessive noise levels
  • when workers are exposed to respiratory hazards only

Questão 22

Questão
Who is responsible for providing workers with WHMIS training?
Responda
  • The supplier of controlled products.
  • A training institute or provider.
  • The employee must obtain their own training.
  • The employer must provide the training.

Questão 23

Questão
Employers are responsible to:
Responda
  • provide a MSDS for each controlled product used in the workplace.
  • inform all workers about chemical hazards at the work site.
  • train workers about labels, MSDS and other identifiers.
  • all of the above.

Questão 24

Questão
Suppliers of controller products are responsible to:
Responda
  • train employees to safely dispose of hazardous products.
  • provide SDS for controlled product they sell or import.
  • provide extra labels for employees to use when transferring controlled products from the original container.
  • visit work sites to ensure controlled products are labelled properly.

Questão 25

Questão
Employees are responsible to:
Responda
  • classify controlled products.
  • train other employees about WHMIS.
  • apply workplace labels where and when required.
  • ensure SDS are readily available.

Questão 26

Questão
The key elements of WHMIS are:
Responda
  • employee education, SDS and product labelling.
  • Hazard Products Act, OHS and SDS.
  • employee labelling, SDS and employer training.
  • product labeling, OHS and Controlled Products Regulations.

Questão 27

Questão
The goal of WHMIS is to:
Responda
  • ensure workers have containers for controlled products.
  • ensure suppliers of controlled products provide training for all employees.
  • protect the worker by providing information on hazardous materials.
  • ensure that the requirements for information on hazardous materials are unique to the requirements of each province.

Questão 28

Questão
An SDS must be provided for each controlled product because they:
Responda
  • provide only the essential information from the label and are easier to read in an emergency.
  • contain the generic product names and are easier to locate and read than the labels on the containers.
  • are only for the employer's use when an emergency arises, and they can be retrieved from a secure location.
  • provide more detailed information than can be provided on a label.

Questão 29

Questão
The supplier label is attached to the:
Responda
  • container in which the product is shipped.
  • container in which the product is stored.
  • work site near where the product is used.
  • invoice when the product is delivered.

Questão 30

Questão
How do you identify a portable gasoline container that is approved for use? It:
Responda
  • is approved under the Alberta Occupational Health and Safety Code.
  • is approved by the Alberta Hazardous Materials Control Regulations.
  • has a MSDS label affixed to the outside of the container.
  • is approved by either one or both of the ULC or CSA.

Questão 31

Questão
Ventilation system requirements for the work site are found in the:
Responda
  • provincial and national building codes.
  • Alberta Occupational Health and Safety Code.
  • WCB Worker Handbook.
  • Alberta Construction Safety Association.

Questão 32

Questão
Before entering a confined workspace you should:
Responda
  • assemble all necessary tools and equipment to ensure easy access while working in the confined space.
  • contact your employer to obtain information on dangerous gases present in the confined workspace.
  • discuss your work plan with other workers who may have worked in a similar confined space.
  • use a gas detector to determine whether the area contains any dangerous fumes or gases.

Questão 33

Questão
What type of fire extinguisher is versatile in fighting different types of fires?
Responda
  • regular dry chemical
  • purple K dry chemical
  • multi-purpose dry chemical
  • dry powder

Questão 34

Questão
Fasteners used in explosive actuated tools are:
Responda
  • common nails with washers
  • manufactured from special steel and tempered
  • very hard and brittle

Questão 35

Questão
A drive pin is a fastener used to:
Responda
  • support wire for suspending a ceiling
  • permanently attach one material to another
  • attach one material to another with a nut

Questão 36

Questão
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener is blunted (meaning it can't fasten) the material is too:
Responda
  • soft
  • hard
  • brittle

Questão 37

Questão
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener penetrates easily, do not fasten because the material is too:
Responda
  • soft
  • hard
  • brittle

Questão 38

Questão
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If material cracks or shatters, do not fasten because the material is too:
Responda
  • soft
  • hard
  • brittle

Questão 39

Questão
A threaded knurled pin is designed for what material?
Responda
  • mild steel
  • concrete block
  • concrete
  • tempered steel

Questão 40

Questão
To be a qualified operator of an explosive actuated tool you must possess:
Responda
  • a valid driver's license from Alberta.
  • firearms training.
  • training in the use of each tool and familiarity with local safety regulations.
  • knowledge of the safety regulations.

Questão 41

Questão
OH&S states that operators of explosive actuated tools should always wear:
Responda
  • work gloves.
  • ear plugs.
  • hard hat.
  • eye protection.

Questão 42

Questão
If a tool is found to be defective, you should:
Responda
  • mark it defective and call a service representative.
  • try to fix it yourself.
  • sell it at a discount.
  • throw it away.

Questão 43

Questão
According to OH&S, what safety equipment is required when using an explosive actuated tool in a confined area such as a small room?
Responda
  • work gloves and hard hat
  • ear plugs and eye protection
  • hard hat and eye protection
  • eye protection and steel-toed boots

Questão 44

Questão
How much oil should be added to tool parts after cleaning?
Responda
  • one or two drops
  • several drops
  • apply liberally to a cloth and wipe all parts
  • none

Questão 45

Questão
What part requires replacement most often in a low velocity tool?
Responda
  • firing pin
  • trigger
  • buffer
  • piston

Questão 46

Questão
The width of the saw blade cut in the workpiece is called:
Responda
  • set.
  • blade pitch.
  • straight or wavy.
  • kerf.

Questão 47

Questão
The purpose of draw filing is to:
Responda
  • remove metal rapidly.
  • produce a smooth and flat surface.
  • finish rough surfaces.
  • remove sharp corners and burrs.

Questão 48

Questão
The removable serrated jaws on a bench vise are made from:
Responda
  • aluminum.
  • hardened steel.
  • cast steel.
  • cast iron.

Questão 49

Questão
A standard screwdriver blade maintains a better grip in the slot if the blade is ground slightly:
Responda
  • tapered.
  • concave.
  • convex.
  • rounded.

Questão 50

Questão
The included angle that should be ground on the point of a center punch is:
Responda
  • 30° to 60°
  • 90°
  • 120°
  • 150°

Questão 51

Questão
When tightening a bolt with a wrench:
Responda
  • an adjustable wrench gives the most precise fit on a hexagon headed bolt.
  • use a pipe on the end of the wrench to increase torque.
  • never push; always pull.
  • never pull; always push.

Questão 52

Questão
The reason for the crown on the end of a flat scraper is:
Responda
  • so that the outside edges do not dig into the finished workpiece.
  • to increase the area of the cutting edge.
  • to produce a sharp cutting edge.
  • to make it easier to scrape internal cylindrical surfaces.

Questão 53

Questão
Which is a purpose of a flat (cold) chisel?
Responda
  • cutting keys and grooves
  • cutting oil grooves
  • cutting off rivets
  • squaring up keyseat corners

Questão 54

Questão
What is a chisel made from?
Responda
  • aluminum
  • high carbon steel
  • low carbon steel
  • stainless steel

Questão 55

Questão
Alkaline cleaning must only be used on which of the following metals.
Responda
  • aluminum
  • zinc
  • lead
  • iron

Questão 56

Questão
Barrel finishing:
Responda
  • is a quick and inexpensive cleaning method.
  • is inexpensive and many parts can be completed at once.
  • uses high pressure air and steam.
  • uses petroleum-based products.

Questão 57

Questão
In the lapping process, which is charged?
Responda
  • the hardened roller
  • the hardened steel block
  • the lap
  • the workpiece

Questão 58

Questão
What is another name for Hand Pads and Rolls?
Responda
  • Scotch-Brite pads
  • scrub pads
  • SoS pads
  • sponge pad

Questão 59

Questão
The three hand taps found in a set are the:
Responda
  • starter, plug and bottoming
  • taper, plug and bottoming
  • taper, intermediate and finishing
  • starter, intermediate and chamfered.

Questão 60

Questão
What is the tap drill size for a 3/4-10 UNC 2B?
Responda
  • 3/4 inch
  • 21/32 inch
  • 37/64 inch
  • 11/16 inch

Questão 61

Questão
If a high-speed steel hand tap breaks in a hole, one way to remove it is:
Responda
  • with an electrical discharge machine.
  • by drilling it out with a high-speed steel drill bit.
  • by drilling a hole and using a stud extractor.
  • with a tap vibrator.

Questão 62

Questão
You have to choose between four steel rods to cut a 1/2-13 UNC 2A thread with an adjustable split die. Which diameter rod would you use?
Responda
  • 0.489
  • 0.497
  • 0.503
  • 0.515

Questão 63

Questão
Choose the correct tool to turn a die.
Responda
  • die wrench
  • die stock
  • die plate
  • die handle

Questão 64

Questão
The cutting action of a hand broach is performed by a series of successive teeth, each protruding:
Responda
  • 0.001 inch further than the preceding tooth.
  • 0.002 inch further than the preceding tooth.
  • 0.0003 inch further than the preceding tooth.
  • 0.003 inch further than the preceding tooth.

Questão 65

Questão
Hand reamers must be rotated:
Responda
  • counter-clockwise.
  • clockwise.
  • in reverse.
  • forward.

Questão 66

Questão
Pullers are used to:
Responda
  • move heavy equipment in a horizontal plane.
  • move heavy equipment in a vertical plane.
  • remove bearings, hubs and sprockets.
  • remove large heavy shafts.

Questão 67

Questão
Before working around a load that has been raised with a hydraulic jack:
Responda
  • the load must be blocked.
  • the jack handle must be removed.
  • the hydraulic fluid should be checked.
  • the jack should be seated on a flat surface.

Questão 68

Questão
Master precision levels should be picked up by the:
Responda
  • bottom surface.
  • vials.
  • top plate.
  • sides.

Questão 69

Questão
A mechanic's level has a sensitivity of:
Responda
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.
  • 0.005 inch per foot per division
  • 0.010 inch per foot per division.

Questão 70

Questão
Levelling feet are used on:
Responda
  • heavy equipment.
  • large machine tools.
  • small lightweight equipment.
  • vibrating equipment.

Questão 71

Questão
You can level machine tools with a carpenter's level.
Responda
  • True
  • False

Questão 72

Questão
Wind can affect both plumb bobs and vertical wires.
Responda
  • True
  • False

Questão 73

Questão
Which anchor bolt can you replace easily if you break it?
Responda
  • fixed
  • flexible
  • drop-in
  • boxed

Questão 74

Questão
Which anchor is designed to accommodate slight adjustment?
Responda
  • fixed
  • flexible
  • expansion bolt
  • drop-in

Questão 75

Questão
Which anchor is best suited for the edge of a concrete foundation?
Responda
  • expansion bolt
  • fixed
  • adhesive
  • drop-in

Questão 76

Questão
Reference lines are also known as:
Responda
  • working lines.
  • control lines.
  • datum lines.
  • all of the above.

Questão 77

Questão
A 12-inch master precision level requires 0.003 inch of shims under one end to bring it level when it is placed longitudinally on the bed of a machine tool eight feet long. What size shim should be placed under the end of the machine tool to level it?
Responda
  • 0.002 inch
  • 0.003 inch
  • 0.012 inch
  • 0.024 inch

Questão 78

Questão
Do not apply grout to a smooth concrete surface.
Responda
  • True
  • False

Questão 79

Questão
Homemade grout mixtures tend to shrink.
Responda
  • True
  • False

Questão 80

Questão
You can place polymeric grouts in colder temperatures than cement-based grouts.
Responda
  • True
  • False

Questão 81

Questão
Before grouting, you should torque anchor bolts:
Responda
  • to their final value.
  • to 50% of their final value.
  • to 25% of their final value.
  • not at all until the grout has cured.

Questão 82

Questão
Grout is so stiff that formwork is not required.
Responda
  • True
  • False

Questão 83

Questão
A master precision level has a sensitivity of:
Responda
  • 5 microns per foot per division.
  • 0.0001 inch per foot per division.
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.

Questão 84

Questão
When using wire sag charts to determine the levelness of a machine bed, deduct the sag from the measured vertical distance to give the true vertical distance.
Responda
  • True
  • False

Questão 85

Questão
Because reference lines are all very accurate, you can take important measurements from either side of any one of them.
Responda
  • True
  • False

Questão 86

Questão
Do not place cement-based grout mixtures below what temperature?
Responda
  • 5°C
  • 0°C
  • -5°C
  • -10°C

Questão 87

Questão
The kind of abrasive material used in grinding wheels for general purpose applications is:
Responda
  • silicon carbide.
  • boron carbide.
  • aluminum oxide.
  • diamond.

Questão 88

Questão
It is safe to carry a portable grinder by the power cord.
Responda
  • True
  • False

Questão 89

Questão
It is safe to use standard sockets with electric impact wrenches.
Responda
  • True
  • False

Questão 90

Questão
The larger the power drill, the slower the rpms and higher the torque.
Responda
  • True
  • False

Questão 91

Questão
Most cordless drills have torque control
Responda
  • True
  • False

Questão 92

Questão
Prolonged use of power or air tools can cause carpal tunnel syndrome.
Responda
  • True
  • False

Quer criar seus próprios Quizzes gratuitos com a GoConqr? Saiba mais.

Semelhante

Tools
JonathanMacIntyre
Power Saws
Vincent Bergeron
Uirlisí Láimhe - Sábha
Cathal Ó Conghaile
Simulado Química ITA
Karoliny Ruppel
Exame Nacional de Portugues
Sandra Franco
Literatura
neusamiotto
Revolução Francesa
Vania Martins
AFO
Graciela Dias
Plano de Aula em 5 minutos
GoConqr suporte .
Tecidos Nervosos
Daniela Barreto3004
História do Islamismo
Marcus Vital
Explore a Biblioteca